From: Jonathan Bakker <xc-racer2@live.ca>
To: kgene@kernel.org, krzk@kernel.org, robh+dt@kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-samsung-soc@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org
Cc: Jonathan Bakker <xc-racer2@live.ca>
Subject: [PATCH v2 02/18] ARM: dts: s5pv210: Add sleep GPIO configuration for fascinate4g
Date: Fri, 1 May 2020 16:50:03 -0700 [thread overview]
Message-ID: <BN6PR04MB06609B7979D7F4004DE5462EA3AB0@BN6PR04MB0660.namprd04.prod.outlook.com> (raw)
In-Reply-To: <20200501235019.24022-1-xc-racer2@live.ca>
In order to minimize leakage current during sleep, set a config
for sleep GPIOs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
---
Changes from v1
- Note where sleep GPIOs came from
---
arch/arm/boot/dts/s5pv210-fascinate4g.dts | 243 ++++++++++++++++++++++
1 file changed, 243 insertions(+)
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
index 07a8d9bbe5b8..65f589e2b72a 100644
--- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
+++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
@@ -36,3 +36,246 @@
};
};
};
+
+&pinctrl0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sleep_cfg>;
+
+ /* Based on vendor kernel v2.6.35.7 */
+ sleep_cfg: sleep-cfg {
+ PIN_SLP(gpa0-0, PREV, NONE);
+ PIN_SLP(gpa0-1, PREV, NONE);
+ PIN_SLP(gpa0-2, PREV, NONE);
+ PIN_SLP(gpa0-3, OUT1, NONE);
+ PIN_SLP(gpa0-4, PREV, NONE);
+ PIN_SLP(gpa0-5, PREV, NONE);
+ PIN_SLP(gpa0-6, PREV, NONE);
+ PIN_SLP(gpa0-7, PREV, NONE);
+
+ PIN_SLP(gpa1-0, INPUT, DOWN);
+ PIN_SLP(gpa1-1, OUT0, NONE);
+ PIN_SLP(gpa1-2, INPUT, DOWN);
+ PIN_SLP(gpa1-3, OUT0, NONE);
+
+ PIN_SLP(gpb-0, OUT0, NONE);
+ PIN_SLP(gpb-1, OUT1, NONE);
+ PIN_SLP(gpb-2, OUT0, NONE);
+ PIN_SLP(gpb-3, PREV, NONE);
+ PIN_SLP(gpb-4, INPUT, NONE);
+ PIN_SLP(gpb-5, PREV, NONE);
+ PIN_SLP(gpb-6, INPUT, DOWN);
+ PIN_SLP(gpb-7, OUT0, NONE);
+
+ PIN_SLP(gpc0-0, OUT0, NONE);
+ PIN_SLP(gpc0-1, INPUT, DOWN);
+ PIN_SLP(gpc0-2, OUT0, NONE);
+ PIN_SLP(gpc0-3, INPUT, DOWN);
+ PIN_SLP(gpc0-4, OUT0, NONE);
+
+ PIN_SLP(gpc1-0, INPUT, DOWN);
+ PIN_SLP(gpc1-1, INPUT, DOWN);
+ PIN_SLP(gpc1-2, INPUT, DOWN);
+ PIN_SLP(gpc1-3, INPUT, DOWN);
+ PIN_SLP(gpc1-4, INPUT, DOWN);
+
+ PIN_SLP(gpd0-0, INPUT, DOWN);
+ PIN_SLP(gpd0-1, OUT0, NONE);
+ PIN_SLP(gpd0-2, INPUT, DOWN);
+ PIN_SLP(gpd0-3, INPUT, DOWN);
+
+ PIN_SLP(gpd1-0, INPUT, NONE);
+ PIN_SLP(gpd1-1, INPUT, NONE);
+ PIN_SLP(gpd1-2, INPUT, DOWN);
+ PIN_SLP(gpd1-3, INPUT, DOWN);
+ PIN_SLP(gpd1-4, INPUT, DOWN);
+ PIN_SLP(gpd1-5, INPUT, DOWN);
+
+ PIN_SLP(gpe0-0, INPUT, DOWN);
+ PIN_SLP(gpe0-1, INPUT, DOWN);
+ PIN_SLP(gpe0-2, INPUT, DOWN);
+ PIN_SLP(gpe0-3, INPUT, DOWN);
+ PIN_SLP(gpe0-4, INPUT, DOWN);
+ PIN_SLP(gpe0-5, INPUT, DOWN);
+ PIN_SLP(gpe0-6, INPUT, DOWN);
+ PIN_SLP(gpe0-7, INPUT, DOWN);
+
+ PIN_SLP(gpe1-0, INPUT, DOWN);
+ PIN_SLP(gpe1-1, INPUT, DOWN);
+ PIN_SLP(gpe1-2, INPUT, DOWN);
+ PIN_SLP(gpe1-3, OUT0, NONE);
+ PIN_SLP(gpe1-4, INPUT, DOWN);
+
+ PIN_SLP(gpf0-0, OUT0, NONE);
+ PIN_SLP(gpf0-1, OUT0, NONE);
+ PIN_SLP(gpf0-2, OUT0, NONE);
+ PIN_SLP(gpf0-3, OUT0, NONE);
+ PIN_SLP(gpf0-4, OUT0, NONE);
+ PIN_SLP(gpf0-5, OUT0, NONE);
+ PIN_SLP(gpf0-6, OUT0, NONE);
+ PIN_SLP(gpf0-7, OUT0, NONE);
+
+ PIN_SLP(gpf1-0, OUT0, NONE);
+ PIN_SLP(gpf1-1, OUT0, NONE);
+ PIN_SLP(gpf1-2, OUT0, NONE);
+ PIN_SLP(gpf1-3, OUT0, NONE);
+ PIN_SLP(gpf1-4, OUT0, NONE);
+ PIN_SLP(gpf1-5, OUT0, NONE);
+ PIN_SLP(gpf1-6, OUT0, NONE);
+ PIN_SLP(gpf1-7, OUT0, NONE);
+
+ PIN_SLP(gpf2-0, OUT0, NONE);
+ PIN_SLP(gpf2-1, OUT0, NONE);
+ PIN_SLP(gpf2-2, OUT0, NONE);
+ PIN_SLP(gpf2-3, OUT0, NONE);
+ PIN_SLP(gpf2-4, OUT0, NONE);
+ PIN_SLP(gpf2-5, OUT0, NONE);
+ PIN_SLP(gpf2-6, OUT0, NONE);
+ PIN_SLP(gpf2-7, OUT0, NONE);
+
+ PIN_SLP(gpf3-0, OUT0, NONE);
+ PIN_SLP(gpf3-1, OUT0, NONE);
+ PIN_SLP(gpf3-2, OUT0, NONE);
+ PIN_SLP(gpf3-3, OUT0, NONE);
+ PIN_SLP(gpf3-4, PREV, NONE);
+ PIN_SLP(gpf3-5, INPUT, DOWN);
+
+ PIN_SLP(gpg0-0, INPUT, DOWN);
+ PIN_SLP(gpg0-1, INPUT, DOWN);
+ PIN_SLP(gpg0-2, INPUT, NONE);
+ PIN_SLP(gpg0-3, INPUT, DOWN);
+ PIN_SLP(gpg0-4, INPUT, DOWN);
+ PIN_SLP(gpg0-5, INPUT, DOWN);
+ PIN_SLP(gpg0-6, INPUT, DOWN);
+
+ PIN_SLP(gpg1-0, OUT0, NONE);
+ PIN_SLP(gpg1-1, OUT1, NONE);
+ PIN_SLP(gpg1-2, PREV, NONE);
+ PIN_SLP(gpg1-3, OUT1, NONE);
+ PIN_SLP(gpg1-4, OUT1, NONE);
+ PIN_SLP(gpg1-5, OUT1, NONE);
+ PIN_SLP(gpg1-6, OUT1, NONE);
+
+ PIN_SLP(gpg2-0, OUT0, NONE);
+ PIN_SLP(gpg2-1, OUT0, NONE);
+ PIN_SLP(gpg2-2, INPUT, NONE);
+ PIN_SLP(gpg2-3, OUT0, NONE);
+ PIN_SLP(gpg2-4, OUT0, NONE);
+ PIN_SLP(gpg2-5, OUT0, NONE);
+ PIN_SLP(gpg2-6, OUT0, NONE);
+
+ PIN_SLP(gpg3-0, PREV, UP);
+ PIN_SLP(gpg3-1, PREV, UP);
+ PIN_SLP(gpg3-2, INPUT, NONE);
+ PIN_SLP(gpg3-3, INPUT, DOWN);
+ PIN_SLP(gpg3-4, OUT0, NONE);
+ PIN_SLP(gpg3-5, OUT0, NONE);
+ PIN_SLP(gpg3-6, INPUT, DOWN);
+
+ PIN_SLP(gpi-0, PREV, NONE);
+ PIN_SLP(gpi-1, INPUT, DOWN);
+ PIN_SLP(gpi-2, PREV, NONE);
+ PIN_SLP(gpi-3, PREV, NONE);
+ PIN_SLP(gpi-4, PREV, NONE);
+ PIN_SLP(gpi-5, INPUT, DOWN);
+ PIN_SLP(gpi-6, INPUT, DOWN);
+
+ PIN_SLP(gpj0-0, INPUT, NONE);
+ PIN_SLP(gpj0-1, INPUT, NONE);
+ PIN_SLP(gpj0-2, INPUT, NONE);
+ PIN_SLP(gpj0-3, INPUT, NONE);
+ PIN_SLP(gpj0-4, INPUT, NONE);
+ PIN_SLP(gpj0-5, INPUT, DOWN);
+ PIN_SLP(gpj0-6, OUT0, NONE);
+ PIN_SLP(gpj0-7, INPUT, NONE);
+
+ PIN_SLP(gpj1-0, OUT1, NONE);
+ PIN_SLP(gpj1-1, OUT0, NONE);
+ PIN_SLP(gpj1-2, INPUT, DOWN);
+ PIN_SLP(gpj1-3, PREV, NONE);
+ PIN_SLP(gpj1-4, PREV, NONE);
+ PIN_SLP(gpj1-5, OUT0, NONE);
+
+ PIN_SLP(gpj2-0, INPUT, DOWN);
+ PIN_SLP(gpj2-1, INPUT, DOWN);
+ PIN_SLP(gpj2-2, OUT0, NONE);
+ PIN_SLP(gpj2-3, INPUT, DOWN);
+ PIN_SLP(gpj2-4, INPUT, DOWN);
+ PIN_SLP(gpj2-5, PREV, NONE);
+ PIN_SLP(gpj2-6, PREV, NONE);
+ PIN_SLP(gpj2-7, INPUT, DOWN);
+
+ PIN_SLP(gpj3-0, INPUT, NONE);
+ PIN_SLP(gpj3-1, INPUT, NONE);
+ PIN_SLP(gpj3-2, OUT0, NONE);
+ PIN_SLP(gpj3-3, INPUT, DOWN);
+ PIN_SLP(gpj3-4, INPUT, NONE);
+ PIN_SLP(gpj3-5, INPUT, NONE);
+ PIN_SLP(gpj3-6, INPUT, NONE);
+ PIN_SLP(gpj3-7, INPUT, NONE);
+
+ PIN_SLP(gpj4-0, INPUT, NONE);
+ PIN_SLP(gpj4-1, INPUT, DOWN);
+ PIN_SLP(gpj4-2, PREV, NONE);
+ PIN_SLP(gpj4-3, INPUT, NONE);
+ PIN_SLP(gpj4-4, INPUT, DOWN);
+
+ PIN_SLP(mp01-0, OUT1, NONE);
+ PIN_SLP(mp01-1, OUT0, NONE);
+ PIN_SLP(mp01-2, INPUT, DOWN);
+ PIN_SLP(mp01-3, INPUT, DOWN);
+ PIN_SLP(mp01-4, OUT1, NONE);
+ PIN_SLP(mp01-5, INPUT, DOWN);
+ PIN_SLP(mp01-6, INPUT, DOWN);
+ PIN_SLP(mp01-7, INPUT, DOWN);
+
+ PIN_SLP(mp02-0, INPUT, DOWN);
+ PIN_SLP(mp02-1, INPUT, DOWN);
+ PIN_SLP(mp02-2, INPUT, NONE);
+ PIN_SLP(mp02-3, INPUT, DOWN);
+
+ PIN_SLP(mp03-0, INPUT, DOWN);
+ PIN_SLP(mp03-1, INPUT, DOWN);
+ PIN_SLP(mp03-2, OUT1, NONE);
+ PIN_SLP(mp03-3, OUT0, NONE);
+ PIN_SLP(mp03-4, INPUT, NONE);
+ PIN_SLP(mp03-5, OUT0, NONE);
+ PIN_SLP(mp03-6, INPUT, DOWN);
+ PIN_SLP(mp03-7, INPUT, DOWN);
+
+ PIN_SLP(mp04-0, INPUT, DOWN);
+ PIN_SLP(mp04-1, OUT0, NONE);
+ PIN_SLP(mp04-2, INPUT, DOWN);
+ PIN_SLP(mp04-3, OUT0, NONE);
+ PIN_SLP(mp04-4, INPUT, DOWN);
+ PIN_SLP(mp04-5, INPUT, DOWN);
+ PIN_SLP(mp04-6, OUT0, NONE);
+ PIN_SLP(mp04-7, INPUT, DOWN);
+
+ PIN_SLP(mp05-0, INPUT, NONE);
+ PIN_SLP(mp05-1, INPUT, NONE);
+ PIN_SLP(mp05-2, INPUT, NONE);
+ PIN_SLP(mp05-3, INPUT, NONE);
+ PIN_SLP(mp05-4, INPUT, DOWN);
+ PIN_SLP(mp05-5, OUT0, NONE);
+ PIN_SLP(mp05-6, INPUT, DOWN);
+ PIN_SLP(mp05-7, PREV, NONE);
+
+ PIN_SLP(mp06-0, INPUT, DOWN);
+ PIN_SLP(mp06-1, INPUT, DOWN);
+ PIN_SLP(mp06-2, INPUT, DOWN);
+ PIN_SLP(mp06-3, INPUT, DOWN);
+ PIN_SLP(mp06-4, INPUT, DOWN);
+ PIN_SLP(mp06-5, INPUT, DOWN);
+ PIN_SLP(mp06-6, INPUT, DOWN);
+ PIN_SLP(mp06-7, INPUT, DOWN);
+
+ PIN_SLP(mp07-0, INPUT, DOWN);
+ PIN_SLP(mp07-1, INPUT, DOWN);
+ PIN_SLP(mp07-2, INPUT, DOWN);
+ PIN_SLP(mp07-3, INPUT, DOWN);
+ PIN_SLP(mp07-4, INPUT, DOWN);
+ PIN_SLP(mp07-5, INPUT, DOWN);
+ PIN_SLP(mp07-6, INPUT, DOWN);
+ PIN_SLP(mp07-7, INPUT, DOWN);
+ };
+};
--
2.20.1
next prev parent reply other threads:[~2020-05-01 23:51 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200426183604.28494-1-xc-racer2@live.ca>
2020-04-26 18:35 ` [PATCH 01/13] arm: dts: s5pv210: Add helper define for sleep gpio config Jonathan Bakker
2020-04-26 18:35 ` [PATCH 02/13] arm: dts: s5pv210: fascinate4g: Add sleep GPIO configuration Jonathan Bakker
2020-04-28 10:02 ` Krzysztof Kozlowski
2020-04-28 23:49 ` Jonathan Bakker
2020-05-01 13:10 ` Krzysztof Kozlowski
2020-04-26 18:35 ` [PATCH 03/13] arm: dts: s5pv210: galaxys: " Jonathan Bakker
2020-04-26 18:35 ` [PATCH 04/13] arm: dts: s5pv210: aries: Set keep-power-in-suspend for SDHCI1 Jonathan Bakker
2020-04-26 18:35 ` [PATCH 05/13] arm: dts: s5pv210: aries: Disable pulls on GPIO i2c adapters Jonathan Bakker
2020-04-26 18:35 ` [PATCH 06/13] arm: dts: s5pv210: aries: Add support for more devices Jonathan Bakker
2020-04-28 10:20 ` Krzysztof Kozlowski
2020-04-28 23:32 ` Jonathan Bakker
2020-05-01 13:31 ` Krzysztof Kozlowski
2020-05-01 19:43 ` Jonathan Bakker
2020-04-26 18:35 ` [PATCH 07/13] arm: dts: s5pv210: galaxys: Add si470x fmradio Jonathan Bakker
2020-04-26 18:35 ` [PATCH 08/13] arm: dts: s5pv210: aries: Disable pull for vibrator ena GPIO Jonathan Bakker
2020-04-26 18:36 ` [PATCH 09/13] arm: dts: s5pv210: Add an ADC node Jonathan Bakker
2020-04-28 10:26 ` Krzysztof Kozlowski
2020-04-28 22:27 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 10/13] arm: dts: s5pv210: aries: Enable " Jonathan Bakker
2020-04-28 10:29 ` Krzysztof Kozlowski
2020-04-28 22:26 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 11/13] arm: dts: s5pv210: Assign clocks to MMC devices Jonathan Bakker
2020-04-26 18:36 ` [PATCH 12/13] arm: dts: s5pv210: Correct FIMC definitions Jonathan Bakker
2020-04-28 10:32 ` Krzysztof Kozlowski
2020-04-28 22:31 ` Jonathan Bakker
2020-04-26 18:36 ` [PATCH 13/13] arm: dts: s5pv210: aries: Set MAX8998 GPIO pulls Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 00/18] S5PV210 and Aries DTS improvements Jonathan Bakker
2020-05-04 15:15 ` Krzysztof Kozlowski
[not found] ` <20200501235019.24022-1-xc-racer2@live.ca>
2020-05-01 23:50 ` [PATCH v2 01/18] ARM: dts: s5pv210: Add helper define for sleep gpio config Jonathan Bakker
2020-05-01 23:50 ` Jonathan Bakker [this message]
2020-05-01 23:50 ` [PATCH v2 03/18] ARM: dts: s5pv210: Add sleep GPIO configuration for galaxys Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 04/18] ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 05/18] ARM: dts: s5pv210: Disable pulls on GPIO i2c adapters for aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 06/18] ARM: dts: s5pv210: Add WM8994 support to aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 07/18] ARM: dts: s5pv210: Add FSA9480 support to Aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 08/18] ARM: dts: s5pv210: Add touchkey support to aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 09/18] ARM: dts: s5pv210: Add panel " Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 10/18] ARM: dts: s5pv210: Add remaining i2c-gpio adapters to aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 11/18] ARM: dts: s5pv210: Add si470x fmradio to galaxys Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 12/18] ARM: dts: s5pv210: Disable pull for vibrator ena GPIO on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 13/18] ARM: dts: s5pv210: Add an ADC node Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 14/18] ARM: dts: s5pv210: Enable ADC on aries boards Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 15/18] ARM: dts: s5pv210: Assign clocks to MMC devices on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 16/18] ARM: dts: s5pv210: Correct FIMC definitions Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 17/18] ARM: dts: s5pv210: Set MAX8998 GPIO pulls on aries Jonathan Bakker
2020-05-01 23:50 ` [PATCH v2 18/18] ARM: dts: s5pv210: Correct gpi gpio node name Jonathan Bakker
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=BN6PR04MB06609B7979D7F4004DE5462EA3AB0@BN6PR04MB0660.namprd04.prod.outlook.com \
--to=xc-racer2@live.ca \
--cc=devicetree@vger.kernel.org \
--cc=kgene@kernel.org \
--cc=krzk@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).