[PATCH 06/13] arm: dts: s5pv210: aries: Add support for more devices

[Jonathan Bakker <xc-racer2@live.ca>]

Add support for following devices:
  - touchkeys connected over i2c-gpio
  - s6e63m0 panel connected over spi-gpio
  - fsa9480 microusb switch over i2c-gpio
  - wm8994 over i2c-gpio (no machine driver yet)
  - all common i2c-gpio devices

Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
---
 arch/arm/boot/dts/s5pv210-aries.dtsi      | 282 ++++++++++++++++++++--
 arch/arm/boot/dts/s5pv210-fascinate4g.dts |   6 +
 2 files changed, 270 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index f83df426f2b6..ef966d13d83d 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -12,8 +12,14 @@
 	compatible = "samsung,aries", "samsung,s5pv210";
 
 	aliases {
+		i2c4 = &i2c_sound;
+		i2c5 = &i2c_accel;
 		i2c6 = &i2c_pmic;
+		i2c7 = &i2c_musb;
 		i2c9 = &i2c_fuel;
+		i2c10 = &i2c_touchkey;
+		i2c11 = &i2c_prox;
+		i2c12 = &i2c_magnetometer;
 	};
 
 	memory@30000000 {
@@ -48,6 +54,18 @@
 		gpio = <&gpj1 1 GPIO_ACTIVE_HIGH>;
 	};
 
+	touchkey_vdd: regulator-fixed-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VTOUCH_3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpj3 2 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchkey_vdd_ena>;
+	};
+
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
@@ -57,7 +75,69 @@
 		power-off-delay-us = <500>;
 	};
 
-	i2c_pmic: i2c-gpio-0 {
+	i2c_sound: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&mp05 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&mp05 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sound_i2c_pins>;
+
+		wm8994: wm8994@1a {
+			compatible = "wlf,wm8994";
+			reg = <0x1a>;
+
+			#sound-dai-cells = <0>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			clocks = <&clocks MOUT_CLKOUT>;
+			clock-names = "MCLK1";
+
+			AVDD2-supply = <&buck3_reg>;
+			DBVDD-supply = <&buck3_reg>;
+			CPVDD-supply = <&buck3_reg>;
+			SPKVDD1-supply = <&buck3_reg>;
+			SPKVDD2-supply = <&buck3_reg>;
+
+			wlf,gpio-cfg = <0xa101 0x8100 0x0100 0x0100 0x8100
+					0xa101 0x0100 0x8100 0x0100 0x0100
+					0x0100>;
+
+			wlf,ldo1ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+			wlf,ldo2ena = <&gpf3 4 GPIO_ACTIVE_HIGH>;
+
+			wlf,lineout1-se;
+			wlf,lineout2-se;
+
+			assigned-clocks = <&clocks MOUT_CLKOUT>;
+			assigned-clock-rates = <0>;
+			assigned-clock-parents = <&xusbxti>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&codec_ldo>;
+		};
+	};
+
+	i2c_accel: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&accel_i2c_pins>;
+
+		/* bma023 accelerometer, no mainline binding */
+	};
+
+	i2c_pmic: i2c-gpio-2 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -137,8 +217,6 @@
 					regulator-name = "VLCD_1.8V";
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
-					/* Till we get panel driver */
-					regulator-always-on;
 
 					regulator-state-mem {
 						regulator-off-in-suspend;
@@ -237,8 +315,6 @@
 					regulator-name = "VCC_3.0V_LCD";
 					regulator-min-microvolt = <3000000>;
 					regulator-max-microvolt = <3000000>;
-					/* Till we get panel driver */
-					regulator-always-on;
 
 					regulator-state-mem {
 						regulator-off-in-suspend;
@@ -309,7 +385,26 @@
 		};
 	};
 
-	i2c_fuel: i2c-gpio-1 {
+	i2c_musb: i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&musb_i2c_pins>;
+
+		fsa9480: musb@25 {
+			compatible = "fcs,fsa9480";
+			reg = <0x25>;
+			interrupt-parent = <&gph2>;
+			interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+
+	i2c_fuel: i2c-gpio-4 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 		scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -328,6 +423,60 @@
 		};
 	};
 
+	i2c_touchkey: i2c-gpio-5 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj3 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj3 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchkey_i2c_pins>;
+
+		touchkey@20 {
+			compatible = "cypress,aries-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&touchkey_vdd>;
+			vcc-supply = <&buck3_reg>;
+			linux,keycodes = <KEY_MENU KEY_BACK
+					  KEY_HOMEPAGE KEY_SEARCH>;
+			interrupt-parent = <&gpj4>;
+			interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_irq>;
+		};
+	};
+
+	i2c_prox: i2c-gpio-6 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpg2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpg0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&prox_i2c_pins>;
+
+		/* Sharp gp2a prox/light sensor, incomplete mainline binding */
+	};
+
+	i2c_magnetometer: i2c-gpio-7 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpj0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpj0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&magnetometer_i2c_pins>;
+
+		/* Yamaha yas529 magnetometer, no mainline binding */
+	};
+
 	vibrator: pwm-vibrator {
 		compatible = "pwm-vibrator";
 		pwms = <&pwm 1 44642 0>;
@@ -343,6 +492,39 @@
 		offset = <0x681c>; /* PS_HOLD_CONTROL */
 		value = <0x5200>;
 	};
+
+	spi_lcd: spi-gpio-0 {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&mp04 1 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&mp04 3 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&mp01 1 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_spi_pins>;
+
+		panel@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
+			vdd3-supply = <&ldo7_reg>;
+			vci-supply = <&ldo17_reg>;
+			spi-cs-high;
+			spi-max-frequency = <1200000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_rst>;
+
+			port {
+				lcd_ep: endpoint {
+					remote-endpoint = <&fimd_ep>;
+				};
+			};
+		};
+	};
 };
 
 &fimd {
@@ -353,18 +535,13 @@
 	samsung,invert-vden;
 	samsung,invert-vclk;
 
-	display-timings {
-		timing-0 {
-			/* 480x800@60Hz */
-			clock-frequency = <25628040>;
-			hactive = <480>;
-			vactive = <800>;
-			hfront-porch = <16>;
-			hback-porch = <16>;
-			hsync-len = <2>;
-			vfront-porch = <28>;
-			vback-porch = <1>;
-			vsync-len = <2>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@3 {
+		reg = <3>;
+		fimd_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
 		};
 	};
 };
@@ -405,6 +582,19 @@
 		samsung,pin-val = <1>;
 	};
 
+	codec_ldo: codec-ldo {
+		samsung,pins = "gpf3-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+	};
+
+	prox_i2c_pins: gp2a-i2c-pins {
+		samsung,pins = "gpg0-2", "gpg2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	wlan_gpio_rst: wlan-gpio-rst {
 		samsung,pins = "gpg1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -438,6 +628,13 @@
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
+	magnetometer_i2c_pins: yas529-i2c-pins {
+		samsung,pins = "gpj0-0", "gpj0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	ts_irq: ts-irq {
 		samsung,pins = "gpj0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
@@ -445,17 +642,66 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
+	touchkey_i2c_pins: touchkey-i2c-pins {
+		samsung,pins = "gpj3-0", "gpj3-1";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	touchkey_vdd_ena: touchkey-vdd-ena {
+		samsung,pins = "gpj3-2";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	musb_i2c_pins: musb-i2c-pins {
+		samsung,pins = "gpj3-4", "gpj3-5";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	accel_i2c_pins: accel-i2c-pins {
+		samsung,pins = "gpj3-6", "gpj3-7";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	pmic_i2c_pins: pmic-i2c-pins {
 		samsung,pins = "gpj4-0", "gpj4-3";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
+	touchkey_irq: touchkey-irq {
+		samsung,pins = "gpj4-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	lcd_spi_pins: spi-lcd-pins {
+		samsung,pins = "mp01-1", "mp04-1", "mp04-3";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
 	fg_i2c_pins: fg-i2c-pins {
 		samsung,pins = "mp05-0", "mp05-1";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
+
+	sound_i2c_pins: sound-i2c-pins {
+		samsung,pins = "mp05-2", "mp05-3";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
+
+	panel_rst: panel-rst {
+		samsung,pins = "mp05-5";
+		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+	};
 };
 
 &pwm {
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
index 94dcb9b64b9a..42e6e2de197d 100644
--- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
+++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
@@ -278,3 +278,9 @@
 		PIN_SLP(mp07-7, INPUT, DOWN);
 	};
 };
+
+&wm8994 {
+	/* GPIO3 (BCLK2) and GPIO4 (LRCLK2) as outputs */
+	wlf,gpio-cfg = <0xa101 0x8100 0x8100 0x8100 0x8100 0xa101
+		0x0100 0x8100 0x0100 0x0100 0x0100>;
+};
-- 
2.20.1