From: Simon Glass <sjg@chromium.org>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH 26/93] arm: Remove gwventana_gw5904 board
Date: Mon, 19 Nov 2018 08:53:06 -0700 [thread overview]
Message-ID: <20181119155413.158098-27-sjg@chromium.org> (raw)
In-Reply-To: <20181119155413.158098-1-sjg@chromium.org>
This board has not been converted to CONFIG_DM_BLK by the deadline.
Remove it.
Signed-off-by: Simon Glass <sjg@chromium.org>
---
arch/arm/mach-imx/mx6/Kconfig | 1 -
board/gateworks/gw_ventana/Kconfig | 25 -
board/gateworks/gw_ventana/MAINTAINERS | 8 -
board/gateworks/gw_ventana/Makefile | 11 -
board/gateworks/gw_ventana/README | 320 -----
board/gateworks/gw_ventana/common.c | 1422 -------------------
board/gateworks/gw_ventana/common.h | 98 --
board/gateworks/gw_ventana/eeprom.c | 238 ----
board/gateworks/gw_ventana/gsc.c | 274 ----
board/gateworks/gw_ventana/gsc.h | 70 -
board/gateworks/gw_ventana/gw_ventana.c | 1351 ------------------
board/gateworks/gw_ventana/gw_ventana_spl.c | 691 ---------
board/gateworks/gw_ventana/ventana_eeprom.h | 133 --
configs/gwventana_emmc_defconfig | 88 --
configs/gwventana_gw5904_defconfig | 92 --
configs/gwventana_nand_defconfig | 91 --
include/configs/gw_ventana.h | 355 -----
17 files changed, 5268 deletions(-)
delete mode 100644 board/gateworks/gw_ventana/Kconfig
delete mode 100644 board/gateworks/gw_ventana/MAINTAINERS
delete mode 100644 board/gateworks/gw_ventana/Makefile
delete mode 100644 board/gateworks/gw_ventana/README
delete mode 100644 board/gateworks/gw_ventana/common.c
delete mode 100644 board/gateworks/gw_ventana/common.h
delete mode 100644 board/gateworks/gw_ventana/eeprom.c
delete mode 100644 board/gateworks/gw_ventana/gsc.c
delete mode 100644 board/gateworks/gw_ventana/gsc.h
delete mode 100644 board/gateworks/gw_ventana/gw_ventana.c
delete mode 100644 board/gateworks/gw_ventana/gw_ventana_spl.c
delete mode 100644 board/gateworks/gw_ventana/ventana_eeprom.h
delete mode 100644 configs/gwventana_emmc_defconfig
delete mode 100644 configs/gwventana_gw5904_defconfig
delete mode 100644 configs/gwventana_nand_defconfig
delete mode 100644 include/configs/gw_ventana.h
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index ed551b245c9..7c7435b6d89 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -549,7 +549,6 @@ source "board/freescale/mx6ul_14x14_evk/Kconfig"
source "board/freescale/mx6ullevk/Kconfig"
source "board/grinn/liteboard/Kconfig"
source "board/phytec/pfla02/Kconfig"
-source "board/gateworks/gw_ventana/Kconfig"
source "board/kosagi/novena/Kconfig"
source "board/liebherr/display5/Kconfig"
source "board/liebherr/mccmon6/Kconfig"
diff --git a/board/gateworks/gw_ventana/Kconfig b/board/gateworks/gw_ventana/Kconfig
deleted file mode 100644
index 5d1bae41ac5..00000000000
--- a/board/gateworks/gw_ventana/Kconfig
+++ /dev/null
@@ -1,25 +0,0 @@
-if TARGET_GW_VENTANA
-
-config SYS_BOARD
- default "gw_ventana"
-
-config SYS_VENDOR
- default "gateworks"
-
-config SYS_CONFIG_NAME
- default "gw_ventana"
-
-config CMD_EECONFIG
- bool "Enable the 'econfig' command"
- help
- Provides access to EEPROM configuration on Gateworks Ventana
-
-config CMD_GSC
- bool "Enable the 'gsc' command"
- help
- Provides access to the GSC configuration:
-
- gsc sleep - sleeps for a period of seconds
- gsc wd - enables / disables the watchdog
-
-endif
diff --git a/board/gateworks/gw_ventana/MAINTAINERS b/board/gateworks/gw_ventana/MAINTAINERS
deleted file mode 100644
index 265ddac1c05..00000000000
--- a/board/gateworks/gw_ventana/MAINTAINERS
+++ /dev/null
@@ -1,8 +0,0 @@
-GW_VENTANA BOARD
-M: Tim Harvey <tharvey@gateworks.com>
-S: Maintained
-F: board/gateworks/gw_ventana/
-F: include/configs/gw_ventana.h
-F: configs/gwventana_nand_defconfig
-F: configs/gwventana_emmc_defconfig
-F: configs/gwventana_gw5904_defconfig
diff --git a/board/gateworks/gw_ventana/Makefile b/board/gateworks/gw_ventana/Makefile
deleted file mode 100644
index 8fa691aefc4..00000000000
--- a/board/gateworks/gw_ventana/Makefile
+++ /dev/null
@@ -1,11 +0,0 @@
-#
-# Copyright (C) 2012-2013, Guennadi Liakhovetski <lg@denx.de>
-# (C) Copyright 2012-2013 Freescale Semiconductor, Inc.
-# Copyright (C) 2013, Gateworks Corporation
-#
-# SPDX-License-Identifier: GPL-2.0+
-#
-
-obj-y := gw_ventana.o gsc.o eeprom.o common.o
-obj-$(CONFIG_SPL_BUILD) += gw_ventana_spl.o
-
diff --git a/board/gateworks/gw_ventana/README b/board/gateworks/gw_ventana/README
deleted file mode 100644
index 57c64a1b2ad..00000000000
--- a/board/gateworks/gw_ventana/README
+++ /dev/null
@@ -1,320 +0,0 @@
-U-Boot for the Gateworks Ventana Product Family boards
-
-This file contains information for the port of U-Boot to the Gateworks
-Ventana Product family boards.
-
-The entire Ventana product family (http://www.gateworks.com/product#ventana)
-is supported by a single bootloader build by using a common SPL and U-Boot
-that dynamically determines the characterstics of the board at runtime via
-information from an EEPROM on the board programmed at the factory and supports
-all of the various boot mediums available.
-
-1. Secondary Program Loader (SPL)
----------------------------------
-
-The i.MX6 has a BOOT ROM PPL (Primary Program Loader) which supports loading
-an executable image from various boot devices.
-
-The Gateworks Ventana board config uses an SPL build configuration. This
-will build the following artifacts from U-Boot source:
- - SPL - Secondary Program Loader that the i.MX6 BOOT ROM (Primary Program
- Loader) boots. This detects CPU/DRAM configuration, configures
- The DRAM controller, loads u-boot.img from the detected boot device,
- and jumps to it. As this is booted from the PPL, it has an IVT/DCD
- table.
- - u-boot.img - The main U-Boot core which is u-boot.bin with a image header.
-
-
-2. Build
---------
-
-To build U-Boot for the Gateworks Ventana product family:
-
-For NAND FLASH based boards:
- make gwventana_nand_config
- make
-
-For EMMC FLASH based boards:
- make gwventana_emmc_config
- make
-
-
-3. Boot source:
----------------
-
-The Gateworks Ventana boards support booting from NAND or micro-SD depending
-on the board model. The IMX6 BOOT ROM will choose a boot media based on eFUSE
-settings programmed at the factory.
-
-Boards with NAND flash will always boot from NAND, and NAND-less boards will
-always boot from micro-SD. However, it is possible to use the U-Boot bmode
-command (or the technique it uses) to essentially bootstrap to another boot
-media at runtime.
-
-3.1. boot from NAND
--------------------
-
-The i.MX6 BOOT ROM expects some structures that provide details of NAND layout
-and bad block information (referred to as 'bootstreams') which are replicated
-multiple times in NAND. The number of replications and their spacing (referred
-to as search stride) is configurable through board strapping options and/or
-eFUSE settings (BOOT_SEARCH_COUNT / Pages in block from BOOT_CFG2). In
-addition, the i.MX6 BOOT ROM Flash Configuration Block (FCB) supports two
-copies of a bootloader in flash in the case that a bad block has corrupted one.
-The Freescale 'kobs-ng' application from the Freescale LTIB BSP, which runs
-under Linux and operates on an MTD partition, must be used to program the
-bootstream in order to setup this flash structure correctly.
-
-The Gateworks Ventana boards with NAND flash have been factory programmed
-such that their eFUSE settings expect 2 copies of the boostream (this is
-specified by providing kobs-ng with the --search_exponent=1 argument). Once in
-Linux with MTD support for the NAND on /dev/mtd0 you can program the SPL
-with:
-
-kobs-ng init -v -x --search_exponent=1 SPL
-
-The kobs-ng application uses an imximage which contains the Image Vector Table
-(IVT) and Device Configuration Data (DCD) structures that the i.MX6 BOOT ROM
-requires to boot. The kobs-ng adds the Firmware Configuration Block (FCB) and
-Discovered Bad Block Table (DBBT). The SPL build artifact from U-Boot is
-an imximage.
-
-The u-boot.img, which is the non SPL U-Boot binary appended to a U-Boot image
-header must be programmed in the NAND flash boot device at an offset hard
-coded in the SPL. For the Ventana boards, this has been chosen to be 14MB.
-The image can be programmed from either U-Boot or Linux:
-
-U-Boot:
-Ventana > setenv mtdparts mtdparts=nand:14m(spl),2m(uboot),1m(env),-(rootfs)
-Ventana > tftp ${loadaddr} u-boot.img && nand erase.part uboot && \
- nand write ${loadaddr} uboot ${filesize}
-
-Linux:
-nandwrite /dev/mtd1 u-boot.img
-
-The above assumes the default Ventana partitioning scheme which is configured
-via the mtdparts env var:
- - spl: 14MB
- - uboot: 2M
- - env: 1M
- - rootfs: the rest
-
-This information is taken from:
- http://trac.gateworks.com/wiki/ventana/bootloader#nand
-
-More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
-
-3.1. boot from MMC (eMMC/microSD)
----------------------------------
-
-When the IMX6 eFUSE settings have been factory programmed to boot from
-MMC the SPL will be loaded from offset 0x400 (1KB). Once the SPL is
-booted, it will load and execute U-Boot (u-boot.img) from offset 69KB
-on the micro-SD (defined by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR).
-
-While it is technically possible to enable the SPL to be able to load
-U-Boot from a file on a FAT/EXT filesystem on the micro-SD, we chose to
-use raw micro-SD access to keep the code-size and boot time of the SPL down.
-
-For these reasons an MMC device that will be used as an IMX6 primary boot
-device must be carefully partitioned and prepared.
-
-The following shell commands are executed on a Linux host (adjust DEV to the
-block storage device of your MMC, ie /dev/mmcblk0):
-
- DEV=/dev/sdc
- # zero out 1MB of device
- sudo dd if=/dev/zero of=$DEV count=1 bs=1M oflag=sync status=none && sync
- # copy SPL to 1KB offset
- sudo dd if=SPL of=$DEV bs=1K seek=1 oflag=sync status=none && sync
- # copy U-Boot to 69KB offset
- sudo dd if=u-boot.img of=$DEV bs=1K seek=69 oflag=sync status=none && sync
- # create a partition table with a single rootfs partition starting at 1MB
- printf "1,,L\n" | sudo sfdisk --in-order --no-reread -L -uM $DEV && sync
- # format partition
- sudo mkfs.ext4 -L root ${DEV}1
- # mount the partition
- sudo udisks --mount ${DEV}1
- # extract filesystem
- sudo tar xvf rootfs.tar.gz -C /media/root
- # flush and unmount
- sync && sudo umount /media/root
-
-The above assumes the default Ventana micro-SD partitioning scheme
- - spl : 1KB-69KB (68KB) required by IMX6 BOOT ROM
- - uboot : 69KB-709KB (640KB) defined by
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
- - env : 709KB-965KB (256KB) defined by
- CONFIG_ENV_MMC_SIZE
- CONFIG_ENV_MMC_OFFSET_REDUND
- - rootfs : 1MB-
-
-This information is taken from:
- http://trac.gateworks.com/wiki/ventana/bootloader#microsd
-
-More details about the i.MX6 BOOT ROM can be found in the IMX6 reference manual.
-
-4. Falcon Mode
-------------------------------
-
-The Gateworks Ventana board config enables Falcon mode (CONFIG_SPL_OS_BOOT)
-which allows the SPL to boot directly to an OS instead of to U-Boot
-(u-boot.img) thus acheiving a faster overall boot time. The time savings
-depends on your boot medium (ie NAND Flash vs micro-SD) and size/storage
-of the OS. The time savings can be anywhere from 2 seconds (256MB NAND Flash
-with ~1MB kernel) to 6 seconds or more (2GB NAND Flash with ~6 kernel)
-
-The Gateworks Ventana board supports Falcon mode for the following boot
-medium:
- - NAND flash
- - micro-SD
-
-For all boot mediums, raw mode is used. While support of more complex storage
-such as files on top of FAT/EXT filesystem is possible but not practical
-as the size of the SPL is fairly limitted (to 64KB based on the smallest
-size of available IMX6 iRAM) as well as the fact that this would increase
-OS load time which defeats the purpose of Falcon mode in the first place.
-
-The SPL decides to boot either U-Boot (u-boot.img) or the OS (args + kernel)
-based on the return value of the spl_start_uboot() function. While often
-this can simply be the state of a GPIO based pushbutton or DIP switch, for
-Gateworks Ventana, we use an EEPROM register on i2c-0 at 0x50:0x00:
-set to '0' will choose to boot to U-Boot and otherwise it will boot to OS.
-
-To use Falcon mode it is required that you first 'prepare' the 'args' data
-that is stored on your boot medium along with the kernel (which can be any
-OS or bare-metal application). In the case of the Linux kernel the 'args'
-is the flatenned device-tree which normally gets altered prior to booting linux
-by U-Boot's 'bootm' command. To achieve this for SPL we use the
-'spl export fdt' command in U-Boot after loading the kernel and dtb which
-will go through the same process of modifying the device-tree for the board
-being executed on but not jump to the kernel. This allows you to save the
-args data to the location the SPL expects it and then enable Falcon mode.
-
-It is important to realize that there are certain values in the dtb that
-are board model specific (IMX6Q vs IMX6DL for example) and board specific
-(board serial number, MAC addrs) so you do not want to use the 'args'
-data prepared from one board on another board.
-
-4.1. Falcon Mode on NAND flash
-------------------------------
-To prepare a Gateworks Ventana board that boots from NAND flash for Falcon
-mode you must program your flash such that the 'args' and 'kernel' are
-located where defined at compile time by the following:
- CONFIG_CMD_SPL_NAND_OFS 17MB - offset of 'args'
- CONFIG_SYS_NAND_SPL_KERNEL_OFFS 18MB - offset of 'kernel'
-
-The location offsets defined above are defaults chosen by Gateworks and are
-flexible if you want to re-define them.
-
-The following steps executed in U-Boot will configure Falcon mode for NAND
-using rootfs (ubi), kernel (uImage), and dtb from the network:
-
- # change mtd partitions to the above mapping
- Ventana > setenv mtdparts 'mtdparts=nand:14m(spl),2m(uboot),1m(env),1m(args),10m(kernel),-(rootfs)'
-
- # flash rootfs (at 28MB)
- Ventana > tftp ${loadaddr} rootfs_${flash_layout}.ubi && \
- nand erase.part rootfs && nand write ${loadaddr} rootfs ${filesize}
-
- # load the device-tree
- Ventana > tftp ${fdt_addr} ventana/${fdt_file2}
-
- # load the kernel
- Ventana > tftp ${loadaddr} ventana/uImage
-
- # flash kernel (at 18MB)
- Ventana > nand erase.part kernel && nand write ${loadaddr} kernel ${filesize}
-
- # set kernel args for the console and rootfs (used by spl export)
- Ventana > setenv bootargs 'console=ttymxc1,115200 root=ubi0:rootfs ubi.mtd=5 rootfstype=ubifs quiet'
-
- # create args based on env, board, EEPROM, and dtb
- Ventana > spl export fdt ${loadaddr} - ${fdt_addr}
-
- # flash args (at 17MB)
- Ventana > nand erase.part args && nand write 18000000 args 100000
-
- # set i2c register 0x50:0x00=0 to boot to Linux
- Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1
-
-Be sure to adjust 'bootargs' above to your OS needs (this will be different
-for various distros such as OpenWrt, Yocto, Android, etc). You can use the
-value obtained from 'cat /proc/cmdline' when booted to Linux.
-
-This information is taken from:
- http://trac.gateworks.com/wiki/ventana/bootloader/falcon-mode#nand
-
-
-4.2. Falcon Mode on micro-SD card
----------------------------------
-
-To prepare a Gateworks Ventana board with a primary boot device of micro-SD
-you first need to make sure you build U-Boot with CONFIG_ENV_IS_IN_MMC
-instead of CONFIG_ENV_IS_IN_NAND.
-
-For micro-SD based Falcon mode you must program your micro-SD such that
-the 'args' and 'kernel' are located where defined at compile time
-by the following:
- CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 (1MB) - offset of 'args'
- CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 (2MB) - offset of 'kernel'
-
-The location offsets defined above are defaults chosen by Gateworks and are
-flexible if you want to re-define them.
-
-First you must prepare a micro-SD such that the SPL can be loaded by the
-IMX6 BOOT ROM (fixed offset of 1KB), and U-Boot can be loaded by the SPL
-(fixed offset of 69KB defined by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR).
-
-The following shell commands are executed on a Linux host (adjust DEV to the
-block storage device of your micro-SD):
-
- DEV=/dev/sdc
- # zero out 1MB of device
- sudo dd if=/dev/zero of=$DEV count=1 bs=1M oflag=sync status=none && sync
- # copy SPL to 1KB offset
- sudo dd if=SPL of=$DEV bs=1K seek=1 oflag=sync status=none && sync
- # copy U-Boot to 69KB offset
- sudo dd if=u-boot.img of=$DEV bs=1K seek=69 oflag=sync status=none && sync
- # create a partition table with a single rootfs partition starting at 10MB
- printf "10,,L\n" | sudo sfdisk --in-order --no-reread -L -uM $DEV && sync
- # format partition
- sudo mkfs.ext4 -L root ${DEV}1
- # mount the partition
- sudo udisks --mount ${DEV}1
- # extract filesystem
- sudo tar xvf rootfs.tar.gz -C /media/root
- # flush and unmount
- sync && sudo umount /media/root
-
-Now that your micro-SD partitioning has been adjusted to leave room for the
-raw 'args' and 'kernel' data boot the board with the prepared micro-SD, break
-out in U-Boot and use the following to enable Falcon mode:
-
- # load device-tree from rootfs
- Ventana > ext2load mmc 0:1 ${fdt_addr} boot/${fdt_file2}
-
- # load kernel from rootfs
- Ventana > ext2load mmc 0:1 ${loadaddr} boot/uImage
-
- # write kernel at 2MB offset
- Ventana > mmc write ${loadaddr} 0x1000 0x4000
-
- # setup kernel bootargs
- Ventana > setenv bootargs 'console=ttymxc1,115200 root=/dev/mmcblk0p1 rootfstype=ext4 rootwait rw'
-
- # prepare args
- Ventana > spl export fdt ${loadaddr} - ${fdt_addr}
-
- # write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors)
- Ventana > mmc write 18000000 0x800 0x800
-
- # set i2c register 0x50:0x00=0 to boot to Linux
- Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1
-
-Be sure to adjust 'bootargs' above to your OS needs (this will be different
-for various distros such as OpenWrt, Yocto, Android, etc). You can use the
-value obtained from 'cat /proc/cmdline' when booted to Linux.
-
-This information is taken from:
- http://trac.gateworks.com/wiki/ventana/bootloader/falcon-mode#microsd
diff --git a/board/gateworks/gw_ventana/common.c b/board/gateworks/gw_ventana/common.c
deleted file mode 100644
index 41fe8dc2403..00000000000
--- a/board/gateworks/gw_ventana/common.c
+++ /dev/null
@@ -1,1422 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2013 Gateworks Corporation
- *
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <fsl_esdhc.h>
-#include <hwconfig.h>
-#include <power/pmic.h>
-#include <power/ltc3676_pmic.h>
-#include <power/pfuze100_pmic.h>
-
-#include "common.h"
-
-/* UART1: Function varies per baseboard */
-static iomux_v3_cfg_t const uart1_pads[] = {
- IOMUX_PADS(PAD_SD3_DAT6__UART1_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT7__UART1_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-};
-
-/* UART2: Serial Console */
-static iomux_v3_cfg_t const uart2_pads[] = {
- IOMUX_PADS(PAD_SD4_DAT7__UART2_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_DAT4__UART2_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
-};
-
-void setup_iomux_uart(void)
-{
- SETUP_IOMUX_PADS(uart1_pads);
- SETUP_IOMUX_PADS(uart2_pads);
-}
-
-/* MMC */
-static iomux_v3_cfg_t const gw5904_emmc_pads[] = {
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-/* 4-bit microSD on SD2 */
-static iomux_v3_cfg_t const gw5904_mmc_pads[] = {
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- /* CD */
- IOMUX_PADS(PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-/* 8-bit eMMC on SD2/NAND */
-static iomux_v3_cfg_t const gw560x_emmc_sd2_pads[] = {
- IOMUX_PADS(PAD_SD2_CLK__SD2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_CMD__SD2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT0__SD2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT1__SD2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT2__SD2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD2_DAT3__SD2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D4__SD2_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D5__SD2_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D6__SD2_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D7__SD2_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
-static iomux_v3_cfg_t const usdhc3_pads[] = {
- IOMUX_PADS(PAD_SD3_CLK__SD3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_CMD__SD3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
- IOMUX_PADS(PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(USDHC_PAD_CTRL)),
-};
-
-/* I2C1: GSC */
-static struct i2c_pads_info mx6q_i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_EIM_D21__I2C1_SCL | PC,
- .gpio_mode = MX6Q_PAD_EIM_D21__GPIO3_IO21 | PC,
- .gp = IMX_GPIO_NR(3, 21)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_EIM_D28__I2C1_SDA | PC,
- .gpio_mode = MX6Q_PAD_EIM_D28__GPIO3_IO28 | PC,
- .gp = IMX_GPIO_NR(3, 28)
- }
-};
-static struct i2c_pads_info mx6dl_i2c_pad_info0 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_EIM_D21__I2C1_SCL | PC,
- .gpio_mode = MX6DL_PAD_EIM_D21__GPIO3_IO21 | PC,
- .gp = IMX_GPIO_NR(3, 21)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_EIM_D28__I2C1_SDA | PC,
- .gpio_mode = MX6DL_PAD_EIM_D28__GPIO3_IO28 | PC,
- .gp = IMX_GPIO_NR(3, 28)
- }
-};
-
-/* I2C2: PMIC/PCIe Switch/PCIe Clock/Mezz */
-static struct i2c_pads_info mx6q_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6Q_PAD_KEY_COL3__GPIO4_IO12 | PC,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6Q_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-static struct i2c_pads_info mx6dl_i2c_pad_info1 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_KEY_COL3__I2C2_SCL | PC,
- .gpio_mode = MX6DL_PAD_KEY_COL3__GPIO4_IO12 | PC,
- .gp = IMX_GPIO_NR(4, 12)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_KEY_ROW3__I2C2_SDA | PC,
- .gpio_mode = MX6DL_PAD_KEY_ROW3__GPIO4_IO13 | PC,
- .gp = IMX_GPIO_NR(4, 13)
- }
-};
-
-/* I2C3: Misc/Expansion */
-static struct i2c_pads_info mx6q_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6Q_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6Q_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6Q_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6Q_PAD_GPIO_6__GPIO1_IO06 | PC,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-static struct i2c_pads_info mx6dl_i2c_pad_info2 = {
- .scl = {
- .i2c_mode = MX6DL_PAD_GPIO_3__I2C3_SCL | PC,
- .gpio_mode = MX6DL_PAD_GPIO_3__GPIO1_IO03 | PC,
- .gp = IMX_GPIO_NR(1, 3)
- },
- .sda = {
- .i2c_mode = MX6DL_PAD_GPIO_6__I2C3_SDA | PC,
- .gpio_mode = MX6DL_PAD_GPIO_6__GPIO1_IO06 | PC,
- .gp = IMX_GPIO_NR(1, 6)
- }
-};
-
-void setup_ventana_i2c(void)
-{
- if (is_cpu_type(MXC_CPU_MX6Q)) {
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6q_i2c_pad_info2);
- } else {
- setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info0);
- setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info1);
- setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &mx6dl_i2c_pad_info2);
- }
-}
-
-/*
- * Baseboard specific GPIO
- */
-static iomux_v3_cfg_t const gw51xx_gpio_pads[] = {
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
-
- /* GPS_SHDN */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* VID_PWR */
- IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw52xx_gpio_pads[] = {
- /* SD3_VSELECT */
- IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
- /* RS232_EN# */
- IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
- /* MSATA_EN */
- IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
- /* CAN_STBY */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* GPS_SHDN */
- IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | DIO_PAD_CFG),
- /* USBOTG_SEL */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* VID_PWR */
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | DIO_PAD_CFG),
- /* PCI_RST# (GW522x) */
- IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23 | DIO_PAD_CFG),
- /* RS485_EN */
- IOMUX_PADS(PAD_SD3_DAT4__GPIO7_IO01 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw53xx_gpio_pads[] = {
- /* SD3_VSELECT */
- IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
- /* RS232_EN# */
- IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
- /* MSATA_EN */
- IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
- /* CAN_STBY */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* USB_HUBRST# */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
- /* DIOI2C_DIS# */
- IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | DIO_PAD_CFG),
- /* GPS_SHDN */
- IOMUX_PADS(PAD_ENET_RXD0__GPIO1_IO27 | DIO_PAD_CFG),
- /* VID_EN */
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | DIO_PAD_CFG),
- /* RS485_EN */
- IOMUX_PADS(PAD_SD3_DAT4__GPIO7_IO01 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw54xx_gpio_pads[] = {
- /* SD3_VSELECT */
- IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
- /* RS232_EN# */
- IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
- /* MSATA_EN */
- IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
- /* CAN_STBY */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* USB_HUBRST# */
- IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16 | DIO_PAD_CFG),
- /* MIPI_DIO */
- IOMUX_PADS(PAD_SD1_DAT3__GPIO1_IO21 | DIO_PAD_CFG),
- /* RS485_EN */
- IOMUX_PADS(PAD_EIM_D24__GPIO3_IO24 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
- /* DIOI2C_DIS# */
- IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | DIO_PAD_CFG),
- /* VID_EN */
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | DIO_PAD_CFG),
- /* RS485_EN */
- IOMUX_PADS(PAD_SD3_DAT4__GPIO7_IO01 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_DISP0_DAT23__GPIO5_IO17 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw551x_gpio_pads[] = {
- /* CAN_STBY */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* PANLED# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw552x_gpio_pads[] = {
- /* MSATA_EN */
- IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG),
- /* USBOTG_SEL */
- IOMUX_PADS(PAD_GPIO_7__GPIO1_IO07 | DIO_PAD_CFG),
- /* USB_HUBRST# */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_ENET_TXD1__GPIO1_IO29 | DIO_PAD_CFG),
- /* MX6_DIO[4:9] */
- IOMUX_PADS(PAD_CSI0_PIXCLK__GPIO5_IO18 | DIO_PAD_CFG),
- IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | DIO_PAD_CFG),
- IOMUX_PADS(PAD_CSI0_VSYNC__GPIO5_IO21 | DIO_PAD_CFG),
- IOMUX_PADS(PAD_CSI0_DAT4__GPIO5_IO22 | DIO_PAD_CFG),
- IOMUX_PADS(PAD_CSI0_DAT5__GPIO5_IO23 | DIO_PAD_CFG),
- IOMUX_PADS(PAD_CSI0_DAT7__GPIO5_IO25 | DIO_PAD_CFG),
- /* PCIEGBE1_OFF# */
- IOMUX_PADS(PAD_GPIO_1__GPIO1_IO01 | DIO_PAD_CFG),
- /* PCIEGBE2_OFF# */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw553x_gpio_pads[] = {
- /* SD3_VSELECT */
- IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL2__GPIO4_IO10 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW2__GPIO4_IO11 | DIO_PAD_CFG),
- /* VID_PWR */
- IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw560x_gpio_pads[] = {
- /* RS232_EN# */
- IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG),
- /* CAN_STBY */
- IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG),
- /* USB_HUBRST# */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
- /* DIOI2C_DIS# */
- IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | DIO_PAD_CFG),
- /* VID_EN */
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | DIO_PAD_CFG),
- /* PCI_RST# */
- IOMUX_PADS(PAD_DISP0_DAT10__GPIO4_IO31 | DIO_PAD_CFG),
- /* RS485_EN */
- IOMUX_PADS(PAD_SD3_DAT4__GPIO7_IO01 | DIO_PAD_CFG),
- /* PCIESKT_WDIS# */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
- /* USBH2_PEN (OTG) */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* 12V0_PWR_EN */
- IOMUX_PADS(PAD_DISP0_DAT5__GPIO4_IO26 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw5903_gpio_pads[] = {
- /* BKLT_12VEN */
- IOMUX_PADS(PAD_GPIO_7__GPIO1_IO07 | DIO_PAD_CFG),
- /* EMMY_PDN# */
- IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02 | DIO_PAD_CFG),
- /* EMMY_CFG1# */
- IOMUX_PADS(PAD_NANDF_D3__GPIO2_IO03 | DIO_PAD_CFG),
- /* EMMY_CFG1# */
- IOMUX_PADS(PAD_NANDF_D4__GPIO2_IO04 | DIO_PAD_CFG),
- /* USBH1_PEN (EHCI) */
- IOMUX_PADS(PAD_EIM_D31__GPIO3_IO31 | DIO_PAD_CFG),
- /* USBH2_PEN (OTG) */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* USBDPC_PEN */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* TOUCH_RST */
- IOMUX_PADS(PAD_KEY_COL1__GPIO4_IO08 | DIO_PAD_CFG),
- /* AUDIO_RST# */
- IOMUX_PADS(PAD_DISP0_DAT23__GPIO5_IO17 | DIO_PAD_CFG),
- /* UART1_TEN# */
- IOMUX_PADS(PAD_CSI0_DAT12__GPIO5_IO30 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG),
- /* LVDS_BKLEN # */
- IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG),
- /* RGMII_PDWN# */
- IOMUX_PADS(PAD_ENET_CRS_DV__GPIO1_IO25 | DIO_PAD_CFG),
- /* TOUCH_IRQ# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* TOUCH_RST# */
- IOMUX_PADS(PAD_KEY_COL1__GPIO4_IO08 | DIO_PAD_CFG),
-};
-
-static iomux_v3_cfg_t const gw5904_gpio_pads[] = {
- /* USB_HUBRST# */
- IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09 | DIO_PAD_CFG),
- /* PANLEDG# */
- IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG),
- /* PANLEDR# */
- IOMUX_PADS(PAD_KEY_ROW0__GPIO4_IO07 | DIO_PAD_CFG),
- /* MX6_LOCLED# */
- IOMUX_PADS(PAD_KEY_ROW4__GPIO4_IO15 | DIO_PAD_CFG),
- /* IOEXP_PWREN# */
- IOMUX_PADS(PAD_EIM_A19__GPIO2_IO19 | DIO_PAD_CFG),
- /* IOEXP_IRQ# */
- IOMUX_PADS(PAD_EIM_A20__GPIO2_IO18 | MUX_PAD_CTRL(IRQ_PAD_CTRL)),
- /* DIOI2C_DIS# */
- IOMUX_PADS(PAD_GPIO_19__GPIO4_IO05 | DIO_PAD_CFG),
- /* UART_RS485 */
- IOMUX_PADS(PAD_DISP0_DAT2__GPIO4_IO23 | DIO_PAD_CFG),
- /* UART_HALF */
- IOMUX_PADS(PAD_DISP0_DAT3__GPIO4_IO24 | DIO_PAD_CFG),
- /* SKT1_WDIS# */
- IOMUX_PADS(PAD_DISP0_DAT17__GPIO5_IO11 | DIO_PAD_CFG),
- /* SKT1_RST# */
- IOMUX_PADS(PAD_DISP0_DAT18__GPIO5_IO12 | DIO_PAD_CFG),
- /* SKT2_WDIS# */
- IOMUX_PADS(PAD_DISP0_DAT19__GPIO5_IO13 | DIO_PAD_CFG),
- /* SKT2_RST# */
- IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | DIO_PAD_CFG),
- /* M2_OFF# */
- IOMUX_PADS(PAD_SD2_DAT0__GPIO1_IO15 | DIO_PAD_CFG),
- /* M2_WDIS# */
- IOMUX_PADS(PAD_SD2_DAT1__GPIO1_IO14 | DIO_PAD_CFG),
- /* M2_RST# */
- IOMUX_PADS(PAD_SD2_DAT2__GPIO1_IO13 | DIO_PAD_CFG),
-};
-
-/* Digital I/O */
-struct dio_cfg gw51xx_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- { IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
- IMX_GPIO_NR(1, 18),
- { IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
- 4
- },
-};
-
-struct dio_cfg gw52xx_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- { IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
- IMX_GPIO_NR(1, 20),
- { 0, 0 },
- 0
- },
-};
-
-struct dio_cfg gw53xx_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
- IMX_GPIO_NR(1, 20),
- { 0, 0 },
- 0
- },
-};
-
-struct dio_cfg gw54xx_dio[] = {
- {
- { IOMUX_PADS(PAD_GPIO_9__GPIO1_IO09) },
- IMX_GPIO_NR(1, 9),
- { IOMUX_PADS(PAD_GPIO_9__PWM1_OUT) },
- 1
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD4_DAT1__GPIO2_IO09) },
- IMX_GPIO_NR(2, 9),
- { IOMUX_PADS(PAD_SD4_DAT1__PWM3_OUT) },
- 3
- },
- {
- { IOMUX_PADS(PAD_SD4_DAT2__GPIO2_IO10) },
- IMX_GPIO_NR(2, 10),
- { IOMUX_PADS(PAD_SD4_DAT2__PWM4_OUT) },
- 4
- },
-};
-
-struct dio_cfg gw551x_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
-};
-
-struct dio_cfg gw552x_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
- IMX_GPIO_NR(1, 20),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_PIXCLK__GPIO5_IO18) },
- IMX_GPIO_NR(5, 18),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20) },
- IMX_GPIO_NR(5, 20),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_VSYNC__GPIO5_IO21) },
- IMX_GPIO_NR(5, 21),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_DAT4__GPIO5_IO22) },
- IMX_GPIO_NR(5, 22),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_DAT5__GPIO5_IO23) },
- IMX_GPIO_NR(5, 23),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_CSI0_DAT7__GPIO5_IO25) },
- IMX_GPIO_NR(5, 25),
- { 0, 0 },
- 0
- },
-};
-
-struct dio_cfg gw553x_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- { IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) },
- IMX_GPIO_NR(1, 18),
- { IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) },
- 4
- },
-};
-
-struct dio_cfg gw560x_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
- IMX_GPIO_NR(1, 20),
- { 0, 0 },
- 0
- },
-};
-
-struct dio_cfg gw5903_dio[] = {
-};
-
-struct dio_cfg gw5904_dio[] = {
- {
- { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) },
- IMX_GPIO_NR(1, 16),
- { 0, 0 },
- 0
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) },
- IMX_GPIO_NR(1, 19),
- { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) },
- 2
- },
- {
- { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) },
- IMX_GPIO_NR(1, 17),
- { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) },
- 3
- },
- {
- {IOMUX_PADS(PAD_SD1_CLK__GPIO1_IO20) },
- IMX_GPIO_NR(1, 20),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D0__GPIO2_IO00) },
- IMX_GPIO_NR(2, 0),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D1__GPIO2_IO01) },
- IMX_GPIO_NR(2, 1),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D2__GPIO2_IO02) },
- IMX_GPIO_NR(2, 2),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D3__GPIO2_IO03) },
- IMX_GPIO_NR(2, 3),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D4__GPIO2_IO04) },
- IMX_GPIO_NR(2, 4),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D5__GPIO2_IO05) },
- IMX_GPIO_NR(2, 5),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D6__GPIO2_IO06) },
- IMX_GPIO_NR(2, 6),
- { 0, 0 },
- 0
- },
- {
- {IOMUX_PADS(PAD_NANDF_D7__GPIO2_IO07) },
- IMX_GPIO_NR(2, 7),
- { 0, 0 },
- 0
- },
-};
-
-/*
- * Board Specific GPIO
- */
-struct ventana gpio_cfg[GW_UNKNOWN] = {
- /* GW5400proto */
- {
- .gpio_pads = gw54xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
- .dio_cfg = gw54xx_dio,
- .dio_num = ARRAY_SIZE(gw54xx_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 10),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 29),
- .mezz_pwren = IMX_GPIO_NR(4, 7),
- .mezz_irq = IMX_GPIO_NR(4, 9),
- .rs485en = IMX_GPIO_NR(3, 24),
- .dioi2c_en = IMX_GPIO_NR(4, 5),
- .pcie_sson = IMX_GPIO_NR(1, 20),
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW51xx */
- {
- .gpio_pads = gw51xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw51xx_gpio_pads)/2,
- .dio_cfg = gw51xx_dio,
- .dio_num = ARRAY_SIZE(gw51xx_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 10),
- },
- .pcie_rst = IMX_GPIO_NR(1, 0),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .gps_shdn = IMX_GPIO_NR(1, 2),
- .vidin_en = IMX_GPIO_NR(5, 20),
- .wdis = IMX_GPIO_NR(7, 12),
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- },
-
- /* GW52xx */
- {
- .gpio_pads = gw52xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw52xx_gpio_pads)/2,
- .dio_cfg = gw52xx_dio,
- .dio_num = ARRAY_SIZE(gw52xx_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 29),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .gps_shdn = IMX_GPIO_NR(1, 27),
- .vidin_en = IMX_GPIO_NR(3, 31),
- .usb_sel = IMX_GPIO_NR(1, 2),
- .wdis = IMX_GPIO_NR(7, 12),
- .msata_en = GP_MSATA_SEL,
- .rs232_en = GP_RS232_EN,
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- .vsel_pin = IMX_GPIO_NR(6, 14),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW53xx */
- {
- .gpio_pads = gw53xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw53xx_gpio_pads)/2,
- .dio_cfg = gw53xx_dio,
- .dio_num = ARRAY_SIZE(gw53xx_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 29),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .gps_shdn = IMX_GPIO_NR(1, 27),
- .vidin_en = IMX_GPIO_NR(3, 31),
- .wdis = IMX_GPIO_NR(7, 12),
- .msata_en = GP_MSATA_SEL,
- .rs232_en = GP_RS232_EN,
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- .vsel_pin = IMX_GPIO_NR(6, 14),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW54xx */
- {
- .gpio_pads = gw54xx_gpio_pads,
- .num_pads = ARRAY_SIZE(gw54xx_gpio_pads)/2,
- .dio_cfg = gw54xx_dio,
- .dio_num = ARRAY_SIZE(gw54xx_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 29),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .rs485en = IMX_GPIO_NR(7, 1),
- .vidin_en = IMX_GPIO_NR(3, 31),
- .dioi2c_en = IMX_GPIO_NR(4, 5),
- .pcie_sson = IMX_GPIO_NR(1, 20),
- .wdis = IMX_GPIO_NR(5, 17),
- .msata_en = GP_MSATA_SEL,
- .rs232_en = GP_RS232_EN,
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- .vsel_pin = IMX_GPIO_NR(6, 14),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW551x */
- {
- .gpio_pads = gw551x_gpio_pads,
- .num_pads = ARRAY_SIZE(gw551x_gpio_pads)/2,
- .dio_cfg = gw551x_dio,
- .dio_num = ARRAY_SIZE(gw551x_dio),
- .leds = {
- IMX_GPIO_NR(4, 7),
- },
- .pcie_rst = IMX_GPIO_NR(1, 0),
- .wdis = IMX_GPIO_NR(7, 12),
- },
-
- /* GW552x */
- {
- .gpio_pads = gw552x_gpio_pads,
- .num_pads = ARRAY_SIZE(gw552x_gpio_pads)/2,
- .dio_cfg = gw552x_dio,
- .dio_num = ARRAY_SIZE(gw552x_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 29),
- .usb_sel = IMX_GPIO_NR(1, 7),
- .wdis = IMX_GPIO_NR(7, 12),
- .msata_en = GP_MSATA_SEL,
- },
-
- /* GW553x */
- {
- .gpio_pads = gw553x_gpio_pads,
- .num_pads = ARRAY_SIZE(gw553x_gpio_pads)/2,
- .dio_cfg = gw553x_dio,
- .dio_num = ARRAY_SIZE(gw553x_dio),
- .leds = {
- IMX_GPIO_NR(4, 10),
- IMX_GPIO_NR(4, 11),
- },
- .pcie_rst = IMX_GPIO_NR(1, 0),
- .vidin_en = IMX_GPIO_NR(5, 20),
- .wdis = IMX_GPIO_NR(7, 12),
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- .vsel_pin = IMX_GPIO_NR(6, 14),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW560x */
- {
- .gpio_pads = gw560x_gpio_pads,
- .num_pads = ARRAY_SIZE(gw560x_gpio_pads)/2,
- .dio_cfg = gw560x_dio,
- .dio_num = ARRAY_SIZE(gw560x_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(4, 31),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .rs232_en = GP_RS232_EN,
- .vidin_en = IMX_GPIO_NR(3, 31),
- .wdis = IMX_GPIO_NR(7, 12),
- .otgpwr_en = IMX_GPIO_NR(4, 15),
- .mmc_cd = IMX_GPIO_NR(7, 0),
- },
-
- /* GW5903 */
- {
- .gpio_pads = gw5903_gpio_pads,
- .num_pads = ARRAY_SIZE(gw5903_gpio_pads)/2,
- .dio_cfg = gw5903_dio,
- .dio_num = ARRAY_SIZE(gw5903_dio),
- .leds = {
- IMX_GPIO_NR(6, 14),
- },
- .otgpwr_en = IMX_GPIO_NR(4, 15),
- .mmc_cd = IMX_GPIO_NR(6, 11),
- },
-
- /* GW5904 */
- {
- .gpio_pads = gw5904_gpio_pads,
- .num_pads = ARRAY_SIZE(gw5904_gpio_pads)/2,
- .dio_cfg = gw5904_dio,
- .dio_num = ARRAY_SIZE(gw5904_dio),
- .leds = {
- IMX_GPIO_NR(4, 6),
- IMX_GPIO_NR(4, 7),
- IMX_GPIO_NR(4, 15),
- },
- .pcie_rst = IMX_GPIO_NR(1, 0),
- .mezz_pwren = IMX_GPIO_NR(2, 19),
- .mezz_irq = IMX_GPIO_NR(2, 18),
- .otgpwr_en = IMX_GPIO_NR(3, 22),
- },
-};
-
-void setup_iomux_gpio(int board, struct ventana_board_info *info)
-{
- int i;
-
- if (board >= GW_UNKNOWN)
- return;
-
- /* board specific iomux */
- imx_iomux_v3_setup_multiple_pads(gpio_cfg[board].gpio_pads,
- gpio_cfg[board].num_pads);
-
- /* RS232_EN# */
- if (gpio_cfg[board].rs232_en) {
- gpio_request(gpio_cfg[board].rs232_en, "rs232_en#");
- gpio_direction_output(gpio_cfg[board].rs232_en, 0);
- }
-
- /* GW522x Uses GPIO3_IO23 for PCIE_RST# */
- if (board == GW52xx && info->model[4] == '2')
- gpio_cfg[board].pcie_rst = IMX_GPIO_NR(3, 23);
-
- /* assert PCI_RST# */
- gpio_request(gpio_cfg[board].pcie_rst, "pci_rst#");
- gpio_direction_output(gpio_cfg[board].pcie_rst, 0);
-
- /* turn off (active-high) user LED's */
- for (i = 0; i < ARRAY_SIZE(gpio_cfg[board].leds); i++) {
- char name[16];
- if (gpio_cfg[board].leds[i]) {
- sprintf(name, "led_user%d", i);
- gpio_request(gpio_cfg[board].leds[i], name);
- gpio_direction_output(gpio_cfg[board].leds[i], 1);
- }
- }
-
- /* MSATA Enable - default to PCI */
- if (gpio_cfg[board].msata_en) {
- gpio_request(gpio_cfg[board].msata_en, "msata_en");
- gpio_direction_output(gpio_cfg[board].msata_en, 0);
- }
-
- /* Expansion Mezzanine IO */
- if (gpio_cfg[board].mezz_pwren) {
- gpio_request(gpio_cfg[board].mezz_pwren, "mezz_pwr");
- gpio_direction_output(gpio_cfg[board].mezz_pwren, 0);
- }
- if (gpio_cfg[board].mezz_irq) {
- gpio_request(gpio_cfg[board].mezz_irq, "mezz_irq#");
- gpio_direction_input(gpio_cfg[board].mezz_irq);
- }
-
- /* RS485 Transmit Enable */
- if (gpio_cfg[board].rs485en) {
- gpio_request(gpio_cfg[board].rs485en, "rs485_en");
- gpio_direction_output(gpio_cfg[board].rs485en, 0);
- }
-
- /* GPS_SHDN */
- if (gpio_cfg[board].gps_shdn) {
- gpio_request(gpio_cfg[board].gps_shdn, "gps_shdn");
- gpio_direction_output(gpio_cfg[board].gps_shdn, 1);
- }
-
- /* Analog video codec power enable */
- if (gpio_cfg[board].vidin_en) {
- gpio_request(gpio_cfg[board].vidin_en, "anavidin_en");
- gpio_direction_output(gpio_cfg[board].vidin_en, 1);
- }
-
- /* DIOI2C_DIS# */
- if (gpio_cfg[board].dioi2c_en) {
- gpio_request(gpio_cfg[board].dioi2c_en, "dioi2c_dis#");
- gpio_direction_output(gpio_cfg[board].dioi2c_en, 0);
- }
-
- /* PCICK_SSON: disable spread-spectrum clock */
- if (gpio_cfg[board].pcie_sson) {
- gpio_request(gpio_cfg[board].pcie_sson, "pci_sson");
- gpio_direction_output(gpio_cfg[board].pcie_sson, 0);
- }
-
- /* USBOTG mux routing */
- if (gpio_cfg[board].usb_sel) {
- gpio_request(gpio_cfg[board].usb_sel, "usb_pcisel");
- gpio_direction_output(gpio_cfg[board].usb_sel, 0);
- }
-
- /* PCISKT_WDIS# (Wireless disable GPIO to miniPCIe sockets) */
- if (gpio_cfg[board].wdis) {
- gpio_request(gpio_cfg[board].wdis, "wlan_dis");
- gpio_direction_output(gpio_cfg[board].wdis, 1);
- }
-
- /* OTG power off */
- if (gpio_cfg[board].otgpwr_en) {
- gpio_request(gpio_cfg[board].otgpwr_en, "usbotg_pwr");
- gpio_direction_output(gpio_cfg[board].otgpwr_en, 0);
- }
-
- /* sense vselect pin to see if we support uhs-i */
- if (gpio_cfg[board].vsel_pin) {
- gpio_request(gpio_cfg[board].vsel_pin, "sd3_vselect");
- gpio_direction_input(gpio_cfg[board].vsel_pin);
- gpio_cfg[board].usd_vsel = !gpio_get_value(gpio_cfg[board].vsel_pin);
- }
-
- /* microSD CD */
- if (gpio_cfg[board].mmc_cd) {
- gpio_request(gpio_cfg[board].mmc_cd, "sd_cd");
- gpio_direction_input(gpio_cfg[board].mmc_cd);
- }
-
- /* Anything else board specific */
- switch(board) {
- case GW560x:
- gpio_request(IMX_GPIO_NR(4, 26), "12p0_en");
- gpio_direction_output(IMX_GPIO_NR(4, 26), 1);
- break;
- case GW5903:
- gpio_request(IMX_GPIO_NR(3, 31) , "usbh1-ehci_pwr");
- gpio_direction_output(IMX_GPIO_NR(3, 31), 1);
- gpio_request(IMX_GPIO_NR(4, 15) , "usbh2-otg_pwr");
- gpio_direction_output(IMX_GPIO_NR(4, 15), 1);
- gpio_request(IMX_GPIO_NR(4, 7) , "usbdpc_pwr");
- gpio_direction_output(IMX_GPIO_NR(4, 15), 1);
- gpio_request(IMX_GPIO_NR(1, 25) , "rgmii_en");
- gpio_direction_output(IMX_GPIO_NR(1, 25), 1);
- gpio_request(IMX_GPIO_NR(4, 6) , "touch_irq#");
- gpio_direction_input(IMX_GPIO_NR(4, 6));
- gpio_request(IMX_GPIO_NR(4, 8) , "touch_rst");
- gpio_direction_output(IMX_GPIO_NR(4, 8), 1);
- gpio_request(IMX_GPIO_NR(1, 7) , "bklt_12ven");
- gpio_direction_output(IMX_GPIO_NR(1, 7), 1);
- break;
- case GW5904:
- gpio_request(IMX_GPIO_NR(5, 11), "skt1_wdis#");
- gpio_direction_output(IMX_GPIO_NR(5, 11), 1);
- gpio_request(IMX_GPIO_NR(5, 12), "skt1_rst#");
- gpio_direction_output(IMX_GPIO_NR(5, 12), 1);
- gpio_request(IMX_GPIO_NR(5, 13), "skt2_wdis#");
- gpio_direction_output(IMX_GPIO_NR(5, 13), 1);
- gpio_request(IMX_GPIO_NR(1, 15), "m2_off#");
- gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
- gpio_request(IMX_GPIO_NR(1, 14), "m2_wdis#");
- gpio_direction_output(IMX_GPIO_NR(1, 14), 1);
- gpio_request(IMX_GPIO_NR(1, 13), "m2_rst#");
- gpio_direction_output(IMX_GPIO_NR(1, 13), 1);
- break;
- }
-}
-
-/* setup GPIO pinmux and default configuration per baseboard and env */
-void setup_board_gpio(int board, struct ventana_board_info *info)
-{
- const char *s;
- char arg[10];
- size_t len;
- int i;
- int quiet = simple_strtol(env_get("quiet"), NULL, 10);
-
- if (board >= GW_UNKNOWN)
- return;
-
- /* RS232_EN# */
- if (gpio_cfg[board].rs232_en) {
- gpio_direction_output(gpio_cfg[board].rs232_en,
- (hwconfig("rs232")) ? 0 : 1);
- }
-
- /* MSATA Enable */
- if (gpio_cfg[board].msata_en && is_cpu_type(MXC_CPU_MX6Q)) {
- gpio_direction_output(GP_MSATA_SEL,
- (hwconfig("msata")) ? 1 : 0);
- }
-
- /* USBOTG Select (PCISKT or FrontPanel) */
- if (gpio_cfg[board].usb_sel) {
- gpio_direction_output(gpio_cfg[board].usb_sel,
- (hwconfig("usb_pcisel")) ? 1 : 0);
- }
-
- /*
- * Configure DIO pinmux/padctl registers
- * see IMX6DQRM/IMX6SDLRM IOMUXC_SW_PAD_CTL_PAD_* register definitions
- */
- for (i = 0; i < gpio_cfg[board].dio_num; i++) {
- struct dio_cfg *cfg = &gpio_cfg[board].dio_cfg[i];
- iomux_v3_cfg_t ctrl = DIO_PAD_CFG;
- unsigned cputype = is_cpu_type(MXC_CPU_MX6Q) ? 0 : 1;
-
- if (!cfg->gpio_padmux[0] && !cfg->gpio_padmux[1])
- continue;
- sprintf(arg, "dio%d", i);
- if (!hwconfig(arg))
- continue;
- s = hwconfig_subarg(arg, "padctrl", &len);
- if (s) {
- ctrl = MUX_PAD_CTRL(simple_strtoul(s, NULL, 16)
- & 0x1ffff) | MUX_MODE_SION;
- }
- if (hwconfig_subarg_cmp(arg, "mode", "gpio")) {
- if (!quiet) {
- printf("DIO%d: GPIO%d_IO%02d (gpio-%d)\n", i,
- (cfg->gpio_param/32)+1,
- cfg->gpio_param%32,
- cfg->gpio_param);
- }
- imx_iomux_v3_setup_pad(cfg->gpio_padmux[cputype] |
- ctrl);
- gpio_requestf(cfg->gpio_param, "dio%d", i);
- gpio_direction_input(cfg->gpio_param);
- } else if (hwconfig_subarg_cmp(arg, "mode", "pwm") &&
- cfg->pwm_padmux) {
- if (!cfg->pwm_param) {
- printf("DIO%d: Error: pwm config invalid\n",
- i);
- continue;
- }
- if (!quiet)
- printf("DIO%d: pwm%d\n", i, cfg->pwm_param);
- imx_iomux_v3_setup_pad(cfg->pwm_padmux[cputype] |
- MUX_PAD_CTRL(ctrl));
- }
- }
-
- if (!quiet) {
- if (gpio_cfg[board].msata_en && is_cpu_type(MXC_CPU_MX6Q)) {
- printf("MSATA: %s\n", (hwconfig("msata") ?
- "enabled" : "disabled"));
- }
- if (gpio_cfg[board].rs232_en) {
- printf("RS232: %s\n", (hwconfig("rs232")) ?
- "enabled" : "disabled");
- }
- }
-}
-
-/* setup board specific PMIC */
-void setup_pmic(void)
-{
- struct pmic *p;
- struct ventana_board_info ventana_info;
- int board = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
- const int i2c_pmic = 1;
- u32 reg;
-
- i2c_set_bus_num(i2c_pmic);
-
- /* configure PFUZE100 PMIC */
- if (!i2c_probe(CONFIG_POWER_PFUZE100_I2C_ADDR)) {
- debug("probed PFUZE100 at 0x%x\n", CONFIG_POWER_PFUZE100_I2C_ADDR);
- power_pfuze100_init(i2c_pmic);
- p = pmic_get("PFUZE100");
- if (p && !pmic_probe(p)) {
- pmic_reg_read(p, PFUZE100_DEVICEID, ®);
- printf("PMIC: PFUZE100 ID=0x%02x\n", reg);
-
- /* Set VGEN1 to 1.5V and enable */
- pmic_reg_read(p, PFUZE100_VGEN1VOL, ®);
- reg &= ~(LDO_VOL_MASK);
- reg |= (LDOA_1_50V | LDO_EN);
- pmic_reg_write(p, PFUZE100_VGEN1VOL, reg);
-
- /* Set SWBST to 5.0V and enable */
- pmic_reg_read(p, PFUZE100_SWBSTCON1, ®);
- reg &= ~(SWBST_MODE_MASK | SWBST_VOL_MASK);
- reg |= (SWBST_5_00V | (SWBST_MODE_AUTO << SWBST_MODE_SHIFT));
- pmic_reg_write(p, PFUZE100_SWBSTCON1, reg);
- }
- }
-
- /* configure LTC3676 PMIC */
- else if (!i2c_probe(CONFIG_POWER_LTC3676_I2C_ADDR)) {
- debug("probed LTC3676@0x%x\n", CONFIG_POWER_LTC3676_I2C_ADDR);
- power_ltc3676_init(i2c_pmic);
- p = pmic_get("LTC3676_PMIC");
- if (!p || pmic_probe(p))
- return;
- puts("PMIC: LTC3676\n");
- /*
- * set board-specific scalar for max CPU frequency
- * per CPU based on the LDO enabled Operating Ranges
- * defined in the respective IMX6DQ and IMX6SDL
- * datasheets. The voltage resulting from the R1/R2
- * feedback inputs on Ventana is 1308mV. Note that this
- * is a bit shy of the Vmin of 1350mV in the datasheet
- * for LDO enabled mode but is as high as we can go.
- */
- switch (board) {
- case GW560x:
- /* mask PGOOD during SW3 transition */
- pmic_reg_write(p, LTC3676_DVB3B,
- 0x1f | LTC3676_PGOOD_MASK);
- /* set SW3 (VDD_ARM) */
- pmic_reg_write(p, LTC3676_DVB3A, 0x1f);
- break;
- case GW5903:
- /* mask PGOOD during SW1 transition */
- pmic_reg_write(p, LTC3676_DVB3B,
- 0x1f | LTC3676_PGOOD_MASK);
- /* set SW3 (VDD_ARM) */
- pmic_reg_write(p, LTC3676_DVB3A, 0x1f);
-
- /* mask PGOOD during SW4 transition */
- pmic_reg_write(p, LTC3676_DVB4B,
- 0x1f | LTC3676_PGOOD_MASK);
- /* set SW4 (VDD_SOC) */
- pmic_reg_write(p, LTC3676_DVB4A, 0x1f);
- break;
- default:
- /* mask PGOOD during SW1 transition */
- pmic_reg_write(p, LTC3676_DVB1B,
- 0x1f | LTC3676_PGOOD_MASK);
- /* set SW1 (VDD_SOC) */
- pmic_reg_write(p, LTC3676_DVB1A, 0x1f);
-
- /* mask PGOOD during SW3 transition */
- pmic_reg_write(p, LTC3676_DVB3B,
- 0x1f | LTC3676_PGOOD_MASK);
- /* set SW3 (VDD_ARM) */
- pmic_reg_write(p, LTC3676_DVB3A, 0x1f);
- }
- }
-}
-
-#ifdef CONFIG_FSL_ESDHC
-static struct fsl_esdhc_cfg usdhc_cfg[2];
-
-int board_mmc_init(bd_t *bis)
-{
- struct ventana_board_info ventana_info;
- int board_type = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
- int ret;
-
- switch (board_type) {
- case GW52xx:
- case GW53xx:
- case GW54xx:
- case GW553x:
- /* usdhc3: 4bit microSD */
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[0].max_bus_width = 4;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
- case GW560x:
- /* usdhc2: 8-bit eMMC */
- SETUP_IOMUX_PADS(gw560x_emmc_sd2_pads);
- usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- usdhc_cfg[0].max_bus_width = 8;
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
- if (ret)
- return ret;
- /* usdhc3: 4-bit microSD */
- SETUP_IOMUX_PADS(usdhc3_pads);
- usdhc_cfg[1].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[1].max_bus_width = 4;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
- case GW5903:
- /* usdhc3: 8-bit eMMC */
- SETUP_IOMUX_PADS(gw5904_emmc_pads);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[0].max_bus_width = 8;
- ret = fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
- if (ret)
- return ret;
- /* usdhc2: 4-bit microSD */
- SETUP_IOMUX_PADS(gw5904_mmc_pads);
- usdhc_cfg[1].esdhc_base = USDHC2_BASE_ADDR;
- usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
- usdhc_cfg[1].max_bus_width = 4;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[1]);
- case GW5904:
- /* usdhc3: 8bit eMMC */
- SETUP_IOMUX_PADS(gw5904_emmc_pads);
- usdhc_cfg[0].esdhc_base = USDHC3_BASE_ADDR;
- usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
- usdhc_cfg[0].max_bus_width = 8;
- return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
- default:
- /* doesn't have MMC */
- return -1;
- }
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- struct ventana_board_info ventana_info;
- struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
- int board = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
- int gpio = gpio_cfg[board].mmc_cd;
-
- /* Card Detect */
- switch (board) {
- case GW560x:
- /* emmc is always present */
- if (cfg->esdhc_base == USDHC2_BASE_ADDR)
- return 1;
- break;
- case GW5903:
- case GW5904:
- /* emmc is always present */
- if (cfg->esdhc_base == USDHC3_BASE_ADDR)
- return 1;
- break;
- }
-
- if (gpio) {
- debug("%s: gpio%d=%d\n", __func__, gpio, gpio_get_value(gpio));
- return !gpio_get_value(gpio);
- }
-
- return -1;
-}
-
-#endif /* CONFIG_FSL_ESDHC */
diff --git a/board/gateworks/gw_ventana/common.h b/board/gateworks/gw_ventana/common.h
deleted file mode 100644
index 8019e27f6e0..00000000000
--- a/board/gateworks/gw_ventana/common.h
+++ /dev/null
@@ -1,98 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Gateworks Corporation
- *
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#ifndef _GWVENTANA_COMMON_H_
-#define _GWVENTANA_COMMON_H_
-
-#include "ventana_eeprom.h"
-
-/* GPIO's common to all baseboards */
-#define GP_PHY_RST IMX_GPIO_NR(1, 30)
-#define GP_RS232_EN IMX_GPIO_NR(2, 11)
-#define GP_MSATA_SEL IMX_GPIO_NR(2, 8)
-
-#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
- PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
-
-#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
-
-#define SPI_PAD_CTRL (PAD_CTL_HYS | \
- PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
-
-#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
- PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
- PAD_CTL_ODE | PAD_CTL_SRE_FAST)
-
-#define IRQ_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
- PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
- PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
-
-#define DIO_PAD_CFG (MUX_PAD_CTRL(IRQ_PAD_CTRL) | MUX_MODE_SION)
-
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-
-/*
- * each baseboard has an optional set user configurable Digital IO lines which
- * can be pinmuxed as a GPIO or in some cases a PWM
- */
-struct dio_cfg {
- iomux_v3_cfg_t gpio_padmux[2];
- unsigned gpio_param;
- iomux_v3_cfg_t pwm_padmux[2];
- unsigned pwm_param;
-};
-
-struct ventana {
- /* pinmux */
- iomux_v3_cfg_t const *gpio_pads;
- int num_pads;
- /* DIO pinmux/val */
- struct dio_cfg *dio_cfg;
- int dio_num;
- /* various gpios (0 if non-existent) */
- int leds[3];
- int pcie_rst;
- int mezz_pwren;
- int mezz_irq;
- int rs485en;
- int gps_shdn;
- int vidin_en;
- int dioi2c_en;
- int pcie_sson;
- int usb_sel;
- int wdis;
- int msata_en;
- int rs232_en;
- int otgpwr_en;
- int vsel_pin;
- int mmc_cd;
- /* various features */
- bool usd_vsel;
-};
-
-extern struct ventana gpio_cfg[GW_UNKNOWN];
-
-/* configure i2c iomux */
-void setup_ventana_i2c(void);
-/* configure uart iomux */
-void setup_iomux_uart(void);
-/* conifgure PMIC */
-void setup_pmic(void);
-/* configure gpio iomux/defaults */
-void setup_iomux_gpio(int board, struct ventana_board_info *);
-/* late setup of GPIO (configuration per baseboard and env) */
-void setup_board_gpio(int board, struct ventana_board_info *);
-
-#endif /* #ifndef _GWVENTANA_COMMON_H_ */
diff --git a/board/gateworks/gw_ventana/eeprom.c b/board/gateworks/gw_ventana/eeprom.c
deleted file mode 100644
index f0ae820988e..00000000000
--- a/board/gateworks/gw_ventana/eeprom.c
+++ /dev/null
@@ -1,238 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Gateworks Corporation
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#include <common.h>
-#include <errno.h>
-#include <i2c.h>
-#include <malloc.h>
-#include <asm/bitops.h>
-
-#include "gsc.h"
-#include "ventana_eeprom.h"
-
-/* read ventana EEPROM, check for validity, and return baseboard type */
-int
-read_eeprom(int bus, struct ventana_board_info *info)
-{
- int i;
- int chksum;
- char baseboard;
- int type;
- unsigned char *buf = (unsigned char *)info;
-
- memset(info, 0, sizeof(*info));
-
- /*
- * On a board with a missing/depleted backup battery for GSC, the
- * board may be ready to probe the GSC before its firmware is
- * running. We will wait here indefinately for the GSC/EEPROM.
- */
- while (1) {
- if (0 == i2c_set_bus_num(bus) &&
- 0 == i2c_probe(GSC_EEPROM_ADDR))
- break;
- mdelay(1);
- }
-
- /* read eeprom config section */
- if (gsc_i2c_read(GSC_EEPROM_ADDR, 0x00, 1, buf, sizeof(*info))) {
- puts("EEPROM: Failed to read EEPROM\n");
- return GW_UNKNOWN;
- }
-
- /* sanity checks */
- if (info->model[0] != 'G' || info->model[1] != 'W') {
- puts("EEPROM: Invalid Model in EEPROM\n");
- return GW_UNKNOWN;
- }
-
- /* validate checksum */
- for (chksum = 0, i = 0; i < sizeof(*info)-2; i++)
- chksum += buf[i];
- if ((info->chksum[0] != chksum>>8) ||
- (info->chksum[1] != (chksum&0xff))) {
- puts("EEPROM: Failed EEPROM checksum\n");
- return GW_UNKNOWN;
- }
-
- /* original GW5400-A prototype */
- baseboard = info->model[3];
- if (strncasecmp((const char *)info->model, "GW5400-A", 8) == 0)
- baseboard = '0';
-
- type = GW_UNKNOWN;
- switch (baseboard) {
- case '0': /* original GW5400-A prototype */
- type = GW54proto;
- break;
- case '1':
- type = GW51xx;
- break;
- case '2':
- type = GW52xx;
- break;
- case '3':
- type = GW53xx;
- break;
- case '4':
- type = GW54xx;
- break;
- case '5':
- if (info->model[4] == '1') {
- type = GW551x;
- break;
- } else if (info->model[4] == '2') {
- type = GW552x;
- break;
- } else if (info->model[4] == '3') {
- type = GW553x;
- break;
- }
- break;
- case '6':
- if (info->model[4] == '0')
- type = GW560x;
- break;
- case '9':
- if (info->model[4] == '0' && info->model[5] == '3')
- type = GW5903;
- if (info->model[4] == '0' && info->model[5] == '4')
- type = GW5904;
- break;
- }
- return type;
-}
-
-/* list of config bits that the bootloader will remove from dtb if not set */
-struct ventana_eeprom_config econfig[] = {
- { "eth0", "ethernet0", EECONFIG_ETH0 },
- { "usb0", NULL, EECONFIG_USB0 },
- { "usb1", NULL, EECONFIG_USB1 },
- { "mmc0", NULL, EECONFIG_SD0 },
- { "mmc1", NULL, EECONFIG_SD1 },
- { "mmc2", NULL, EECONFIG_SD2 },
- { "mmc3", NULL, EECONFIG_SD3 },
- { /* Sentinel */ }
-};
-
-#if defined(CONFIG_CMD_EECONFIG) && !defined(CONFIG_SPL_BUILD)
-static struct ventana_eeprom_config *get_config(const char *name)
-{
- struct ventana_eeprom_config *cfg = econfig;
-
- while (cfg->name) {
- if (0 == strcmp(name, cfg->name))
- return cfg;
- cfg++;
- }
- return NULL;
-}
-
-static u8 econfig_bytes[sizeof(ventana_info.config)];
-static int econfig_init = -1;
-
-static int do_econfig(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- struct ventana_eeprom_config *cfg;
- struct ventana_board_info *info = &ventana_info;
- int i;
-
- if (argc < 2)
- return CMD_RET_USAGE;
-
- /* initialize */
- if (econfig_init != 1) {
- memcpy(econfig_bytes, info->config, sizeof(econfig_bytes));
- econfig_init = 1;
- }
-
- /* list configs */
- if ((strncmp(argv[1], "list", 4) == 0)) {
- cfg = econfig;
- while (cfg->name) {
- printf("%s: %d\n", cfg->name,
- test_bit(cfg->bit, econfig_bytes) ? 1 : 0);
- cfg++;
- }
- }
-
- /* save */
- else if ((strncmp(argv[1], "save", 4) == 0)) {
- unsigned char *buf = (unsigned char *)info;
- int chksum;
-
- /* calculate new checksum */
- memcpy(info->config, econfig_bytes, sizeof(econfig_bytes));
- for (chksum = 0, i = 0; i < sizeof(*info)-2; i++)
- chksum += buf[i];
- debug("old chksum:0x%04x\n",
- (info->chksum[0] << 8) | info->chksum[1]);
- debug("new chksum:0x%04x\n", chksum);
- info->chksum[0] = chksum >> 8;
- info->chksum[1] = chksum & 0xff;
-
- /* write new config data */
- if (gsc_i2c_write(GSC_EEPROM_ADDR, info->config - (u8 *)info,
- 1, econfig_bytes, sizeof(econfig_bytes))) {
- printf("EEPROM: Failed updating config\n");
- return CMD_RET_FAILURE;
- }
-
- /* write new config data */
- if (gsc_i2c_write(GSC_EEPROM_ADDR, info->chksum - (u8 *)info,
- 1, info->chksum, 2)) {
- printf("EEPROM: Failed updating checksum\n");
- return CMD_RET_FAILURE;
- }
-
- printf("Config saved to EEPROM\n");
- }
-
- /* get config */
- else if (argc == 2) {
- cfg = get_config(argv[1]);
- if (cfg) {
- printf("%s: %d\n", cfg->name,
- test_bit(cfg->bit, econfig_bytes) ? 1 : 0);
- } else {
- printf("invalid config: %s\n", argv[1]);
- return CMD_RET_FAILURE;
- }
- }
-
- /* set config */
- else if (argc == 3) {
- cfg = get_config(argv[1]);
- if (cfg) {
- if (simple_strtol(argv[2], NULL, 10)) {
- test_and_set_bit(cfg->bit, econfig_bytes);
- printf("Enabled %s\n", cfg->name);
- } else {
- test_and_clear_bit(cfg->bit, econfig_bytes);
- printf("Disabled %s\n", cfg->name);
- }
- } else {
- printf("invalid config: %s\n", argv[1]);
- return CMD_RET_FAILURE;
- }
- }
-
- else
- return CMD_RET_USAGE;
-
- return CMD_RET_SUCCESS;
-}
-
-U_BOOT_CMD(
- econfig, 3, 0, do_econfig,
- "EEPROM configuration",
- "list - list config\n"
- "save - save config to EEPROM\n"
- "<name> - get config 'name'\n"
- "<name> [0|1] - set config 'name' to value\n"
-);
-
-#endif /* CONFIG_CMD_EECONFIG */
diff --git a/board/gateworks/gw_ventana/gsc.c b/board/gateworks/gw_ventana/gsc.c
deleted file mode 100644
index c31ef117b29..00000000000
--- a/board/gateworks/gw_ventana/gsc.c
+++ /dev/null
@@ -1,274 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2013 Gateworks Corporation
- *
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#include <linux/errno.h>
-#include <common.h>
-#include <i2c.h>
-#include <linux/ctype.h>
-
-#include "ventana_eeprom.h"
-#include "gsc.h"
-
-/*
- * The Gateworks System Controller will fail to ACK a master transaction if
- * it is busy, which can occur during its 1HZ timer tick while reading ADC's.
- * When this does occur, it will never be busy long enough to fail more than
- * 2 back-to-back transfers. Thus we wrap i2c_read and i2c_write with
- * 3 retries.
- */
-int gsc_i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- int retry = 3;
- int n = 0;
- int ret;
-
- while (n++ < retry) {
- ret = i2c_read(chip, addr, alen, buf, len);
- if (!ret)
- break;
- debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr,
- n, ret);
- if (ret != -ENODEV)
- break;
- mdelay(10);
- }
- return ret;
-}
-
-int gsc_i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len)
-{
- int retry = 3;
- int n = 0;
- int ret;
-
- while (n++ < retry) {
- ret = i2c_write(chip, addr, alen, buf, len);
- if (!ret)
- break;
- debug("%s: 0x%02x 0x%02x retry%d: %d\n", __func__, chip, addr,
- n, ret);
- if (ret != -ENODEV)
- break;
- mdelay(10);
- }
- mdelay(100);
- return ret;
-}
-
-static void read_hwmon(const char *name, uint reg, uint size)
-{
- unsigned char buf[3];
- uint ui;
-
- printf("%-8s:", name);
- memset(buf, 0, sizeof(buf));
- if (gsc_i2c_read(GSC_HWMON_ADDR, reg, 1, buf, size)) {
- puts("fRD\n");
- } else {
- ui = buf[0] | (buf[1]<<8) | (buf[2]<<16);
- if (reg == GSC_HWMON_TEMP && ui > 0x8000)
- ui -= 0xffff;
- if (ui == 0xffffff)
- puts("invalid\n");
- else
- printf("%d\n", ui);
- }
-}
-
-int gsc_info(int verbose)
-{
- unsigned char buf[16];
-
- i2c_set_bus_num(0);
- if (gsc_i2c_read(GSC_SC_ADDR, 0, 1, buf, 16))
- return CMD_RET_FAILURE;
-
- printf("GSC: v%d", buf[GSC_SC_FWVER]);
- printf(" 0x%04x", buf[GSC_SC_FWCRC] | buf[GSC_SC_FWCRC+1]<<8);
- printf(" WDT:%sabled", (buf[GSC_SC_CTRL1] & (1<<GSC_SC_CTRL1_WDEN))
- ? "en" : "dis");
- if (buf[GSC_SC_STATUS] & (1 << GSC_SC_IRQ_WATCHDOG)) {
- buf[GSC_SC_STATUS] &= ~(1 << GSC_SC_IRQ_WATCHDOG);
- puts(" WDT_RESET");
- gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, 1,
- &buf[GSC_SC_STATUS], 1);
- }
- if (!gsc_i2c_read(GSC_HWMON_ADDR, GSC_HWMON_TEMP, 1, buf, 2)) {
- int ui = buf[0] | buf[1]<<8;
- if (ui > 0x8000)
- ui -= 0xffff;
- printf(" board temp at %dC", ui / 10);
- }
- puts("\n");
- if (!verbose)
- return CMD_RET_SUCCESS;
-
- read_hwmon("Temp", GSC_HWMON_TEMP, 2);
- read_hwmon("VIN", GSC_HWMON_VIN, 3);
- read_hwmon("VBATT", GSC_HWMON_VBATT, 3);
- read_hwmon("VDD_3P3", GSC_HWMON_VDD_3P3, 3);
- read_hwmon("VDD_ARM", GSC_HWMON_VDD_CORE, 3);
- read_hwmon("VDD_SOC", GSC_HWMON_VDD_SOC, 3);
- read_hwmon("VDD_HIGH", GSC_HWMON_VDD_HIGH, 3);
- read_hwmon("VDD_DDR", GSC_HWMON_VDD_DDR, 3);
- read_hwmon("VDD_5P0", GSC_HWMON_VDD_5P0, 3);
- if (strncasecmp((const char*) ventana_info.model, "GW553", 5))
- read_hwmon("VDD_2P5", GSC_HWMON_VDD_2P5, 3);
- read_hwmon("VDD_1P8", GSC_HWMON_VDD_1P8, 3);
- read_hwmon("VDD_IO2", GSC_HWMON_VDD_IO2, 3);
- switch (ventana_info.model[3]) {
- case '1': /* GW51xx */
- read_hwmon("VDD_IO3", GSC_HWMON_VDD_IO4, 3); /* -C rev */
- break;
- case '2': /* GW52xx */
- break;
- case '3': /* GW53xx */
- read_hwmon("VDD_IO4", GSC_HWMON_VDD_IO4, 3); /* -C rev */
- read_hwmon("VDD_GPS", GSC_HWMON_VDD_IO3, 3);
- break;
- case '4': /* GW54xx */
- read_hwmon("VDD_IO3", GSC_HWMON_VDD_IO4, 3); /* -C rev */
- read_hwmon("VDD_GPS", GSC_HWMON_VDD_IO3, 3);
- break;
- case '5': /* GW55xx */
- break;
- case '6': /* GW560x */
- read_hwmon("VDD_IO4", GSC_HWMON_VDD_IO4, 3);
- read_hwmon("VDD_GPS", GSC_HWMON_VDD_IO3, 3);
- break;
- }
- return 0;
-}
-
-/*
- * The Gateworks System Controller implements a boot
- * watchdog (always enabled) as a workaround for IMX6 boot related
- * errata such as:
- * ERR005768 - no fix scheduled
- * ERR006282 - fixed in silicon r1.2
- * ERR007117 - fixed in silicon r1.3
- * ERR007220 - fixed in silicon r1.3
- * ERR007926 - no fix scheduled
- * see http://cache.freescale.com/files/32bit/doc/errata/IMX6DQCE.pdf
- *
- * Disable the boot watchdog
- */
-int gsc_boot_wd_disable(void)
-{
- u8 reg;
-
- i2c_set_bus_num(CONFIG_I2C_GSC);
- if (!gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) {
- reg |= (1 << GSC_SC_CTRL1_WDDIS);
- if (!gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- return 0;
- }
- puts("Error: could not disable GSC Watchdog\n");
- return 1;
-}
-
-#if defined(CONFIG_CMD_GSC) && !defined(CONFIG_SPL_BUILD)
-static int do_gsc_sleep(cmd_tbl_t *cmdtp, int flag, int argc,
- char * const argv[])
-{
- unsigned char reg;
- unsigned long secs = 0;
-
- if (argc < 2)
- return CMD_RET_USAGE;
-
- secs = simple_strtoul(argv[1], NULL, 10);
- printf("GSC Sleeping for %ld seconds\n", secs);
-
- i2c_set_bus_num(0);
- reg = (secs >> 24) & 0xff;
- if (gsc_i2c_write(GSC_SC_ADDR, 9, 1, ®, 1))
- goto error;
- reg = (secs >> 16) & 0xff;
- if (gsc_i2c_write(GSC_SC_ADDR, 8, 1, ®, 1))
- goto error;
- reg = (secs >> 8) & 0xff;
- if (gsc_i2c_write(GSC_SC_ADDR, 7, 1, ®, 1))
- goto error;
- reg = secs & 0xff;
- if (gsc_i2c_write(GSC_SC_ADDR, 6, 1, ®, 1))
- goto error;
- if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- goto error;
- reg |= (1 << 2);
- if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- goto error;
- reg &= ~(1 << 2);
- reg |= 0x3;
- if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- goto error;
-
- return CMD_RET_SUCCESS;
-
-error:
- printf("i2c error\n");
- return CMD_RET_FAILURE;
-}
-
-static int do_gsc_wd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- unsigned char reg;
-
- if (argc < 2)
- return CMD_RET_USAGE;
-
- if (strcasecmp(argv[1], "enable") == 0) {
- int timeout = 0;
-
- if (argc > 2)
- timeout = simple_strtoul(argv[2], NULL, 10);
- i2c_set_bus_num(0);
- if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- return CMD_RET_FAILURE;
- reg &= ~((1 << GSC_SC_CTRL1_WDEN) | (1 << GSC_SC_CTRL1_WDTIME));
- if (timeout == 60)
- reg |= (1 << GSC_SC_CTRL1_WDTIME);
- else
- timeout = 30;
- reg |= (1 << GSC_SC_CTRL1_WDEN);
- if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- return CMD_RET_FAILURE;
- printf("GSC Watchdog enabled with timeout=%d seconds\n",
- timeout);
- } else if (strcasecmp(argv[1], "disable") == 0) {
- i2c_set_bus_num(0);
- if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- return CMD_RET_FAILURE;
- reg &= ~((1 << GSC_SC_CTRL1_WDEN) | (1 << GSC_SC_CTRL1_WDTIME));
- if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1))
- return CMD_RET_FAILURE;
- printf("GSC Watchdog disabled\n");
- } else {
- return CMD_RET_USAGE;
- }
- return CMD_RET_SUCCESS;
-}
-
-static int do_gsc(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
- if (argc < 2)
- return gsc_info(1);
-
- if (strcasecmp(argv[1], "wd") == 0)
- return do_gsc_wd(cmdtp, flag, --argc, ++argv);
- else if (strcasecmp(argv[1], "sleep") == 0)
- return do_gsc_sleep(cmdtp, flag, --argc, ++argv);
-
- return CMD_RET_USAGE;
-}
-
-U_BOOT_CMD(
- gsc, 4, 1, do_gsc, "GSC configuration",
- "[wd enable [30|60]]|[wd disable]|[sleep <secs>]\n"
- );
-
-#endif /* CONFIG_CMD_GSC */
diff --git a/board/gateworks/gw_ventana/gsc.h b/board/gateworks/gw_ventana/gsc.h
deleted file mode 100644
index 0cce9b1b3a2..00000000000
--- a/board/gateworks/gw_ventana/gsc.h
+++ /dev/null
@@ -1,70 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Gateworks Corporation
- *
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#ifndef __ASSEMBLY__
-
-/* i2c slave addresses */
-#define GSC_SC_ADDR 0x20
-#define GSC_RTC_ADDR 0x68
-#define GSC_HWMON_ADDR 0x29
-#define GSC_EEPROM_ADDR 0x51
-
-/* System Controller registers */
-enum {
- GSC_SC_CTRL0 = 0x00,
- GSC_SC_CTRL1 = 0x01,
- GSC_SC_STATUS = 0x0a,
- GSC_SC_FWCRC = 0x0c,
- GSC_SC_FWVER = 0x0e,
-};
-
-/* System Controller Control1 bits */
-enum {
- GSC_SC_CTRL1_WDTIME = 4, /* 1 = 60s timeout, 0 = 30s timeout */
- GSC_SC_CTRL1_WDEN = 5, /* 1 = enable, 0 = disable */
- GSC_SC_CTRL1_WDDIS = 7, /* 1 = disable boot watchdog */
-};
-
-/* System Controller Interrupt bits */
-enum {
- GSC_SC_IRQ_PB = 0, /* Pushbutton switch */
- GSC_SC_IRQ_SECURE = 1, /* Secure Key erase operation complete */
- GSC_SC_IRQ_EEPROM_WP = 2, /* EEPROM write violation */
- GSC_SC_IRQ_GPIO = 4, /* GPIO change */
- GSC_SC_IRQ_TAMPER = 5, /* Tamper detect */
- GSC_SC_IRQ_WATCHDOG = 6, /* Watchdog trip */
- GSC_SC_IRQ_PBLONG = 7, /* Pushbutton long hold */
-};
-
-/* Hardware Monitor registers */
-enum {
- GSC_HWMON_TEMP = 0x00,
- GSC_HWMON_VIN = 0x02,
- GSC_HWMON_VDD_3P3 = 0x05,
- GSC_HWMON_VBATT = 0x08,
- GSC_HWMON_VDD_5P0 = 0x0b,
- GSC_HWMON_VDD_CORE = 0x0e,
- GSC_HWMON_VDD_HIGH = 0x14,
- GSC_HWMON_VDD_DDR = 0x17,
- GSC_HWMON_VDD_SOC = 0x11,
- GSC_HWMON_VDD_1P8 = 0x1d,
- GSC_HWMON_VDD_IO2 = 0x20,
- GSC_HWMON_VDD_2P5 = 0x23,
- GSC_HWMON_VDD_IO3 = 0x26,
- GSC_HWMON_VDD_IO4 = 0x29,
-};
-
-/*
- * I2C transactions to the GSC are done via these functions which
- * perform retries in the case of a busy GSC NAK'ing the transaction
- */
-int gsc_i2c_read(uchar chip, uint addr, int alen, uchar *buf, int len);
-int gsc_i2c_write(uchar chip, uint addr, int alen, uchar *buf, int len);
-int gsc_info(int verbose);
-int gsc_boot_wd_disable(void);
-#endif
-
diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c
deleted file mode 100644
index c4ec97435f4..00000000000
--- a/board/gateworks/gw_ventana/gw_ventana.c
+++ /dev/null
@@ -1,1351 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2013 Gateworks Corporation
- *
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#include <common.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/mxc_hdmi.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/sata.h>
-#include <asm/mach-imx/spi.h>
-#include <asm/mach-imx/video.h>
-#include <asm/io.h>
-#include <asm/setup.h>
-#include <dm.h>
-#include <dm/platform_data/serial_mxc.h>
-#include <environment.h>
-#include <hwconfig.h>
-#include <i2c.h>
-#include <fdt_support.h>
-#include <fsl_esdhc.h>
-#include <jffs2/load_kernel.h>
-#include <linux/ctype.h>
-#include <miiphy.h>
-#include <mtd_node.h>
-#include <netdev.h>
-#include <pci.h>
-#include <power/pmic.h>
-#include <power/ltc3676_pmic.h>
-#include <power/pfuze100_pmic.h>
-#include <fdt_support.h>
-#include <jffs2/load_kernel.h>
-#include <spi_flash.h>
-
-#include "gsc.h"
-#include "common.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-
-/*
- * EEPROM board info struct populated by read_eeprom so that we only have to
- * read it once.
- */
-struct ventana_board_info ventana_info;
-
-static int board_type;
-
-/* ENET */
-static iomux_v3_cfg_t const enet_pads[] = {
- IOMUX_PADS(PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_TX_CTL__RGMII_TX_CTL |
- MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_ENET_REF_CLK__ENET_TX_CLK |
- MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL)),
- IOMUX_PADS(PAD_RGMII_RX_CTL__RGMII_RX_CTL |
- MUX_PAD_CTRL(ENET_PAD_CTRL)),
- /* PHY nRST */
- IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | DIO_PAD_CFG),
-};
-
-#ifdef CONFIG_CMD_NAND
-static iomux_v3_cfg_t const nfc_pads[] = {
- IOMUX_PADS(PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
- IOMUX_PADS(PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL)),
-};
-
-static void setup_gpmi_nand(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- /* config gpmi nand iomux */
- SETUP_IOMUX_PADS(nfc_pads);
-
- /* config gpmi and bch clock to 100 MHz */
- clrsetbits_le32(&mxc_ccm->cs2cdr,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
- MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
- MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
- MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
-
- /* enable gpmi and bch clock gating */
- setbits_le32(&mxc_ccm->CCGR4,
- MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
- MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
- MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
-
- /* enable apbh clock gating */
- setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
-}
-#endif
-
-static void setup_iomux_enet(int gpio)
-{
- SETUP_IOMUX_PADS(enet_pads);
-
- /* toggle PHY_RST# */
- gpio_request(gpio, "phy_rst#");
- gpio_direction_output(gpio, 0);
- mdelay(10);
- gpio_set_value(gpio, 1);
- mdelay(100);
-}
-
-#ifdef CONFIG_USB_EHCI_MX6
-static iomux_v3_cfg_t const usb_pads[] = {
- IOMUX_PADS(PAD_GPIO_1__USB_OTG_ID | DIO_PAD_CFG),
- IOMUX_PADS(PAD_KEY_COL4__USB_OTG_OC | DIO_PAD_CFG),
- /* OTG PWR */
- IOMUX_PADS(PAD_EIM_D22__GPIO3_IO22 | DIO_PAD_CFG),
-};
-
-int board_ehci_hcd_init(int port)
-{
- int gpio;
-
- SETUP_IOMUX_PADS(usb_pads);
-
- /* Reset USB HUB */
- switch (board_type) {
- case GW53xx:
- case GW552x:
- gpio = (IMX_GPIO_NR(1, 9));
- break;
- case GW54proto:
- case GW54xx:
- gpio = (IMX_GPIO_NR(1, 16));
- break;
- default:
- return 0;
- }
-
- /* request and toggle hub rst */
- gpio_request(gpio, "usb_hub_rst#");
- gpio_direction_output(gpio, 0);
- mdelay(2);
- gpio_set_value(gpio, 1);
-
- return 0;
-}
-
-int board_ehci_power(int port, int on)
-{
- /* enable OTG VBUS */
- if (!port && board_type < GW_UNKNOWN) {
- if (gpio_cfg[board_type].otgpwr_en)
- gpio_set_value(gpio_cfg[board_type].otgpwr_en, on);
- }
- return 0;
-}
-#endif /* CONFIG_USB_EHCI_MX6 */
-
-#ifdef CONFIG_MXC_SPI
-iomux_v3_cfg_t const ecspi1_pads[] = {
- /* SS1 */
- IOMUX_PADS(PAD_EIM_D19__GPIO3_IO19 | MUX_PAD_CTRL(SPI_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL)),
- IOMUX_PADS(PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL)),
-};
-
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
- return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(3, 19)) : -1;
-}
-
-static void setup_spi(void)
-{
- gpio_request(IMX_GPIO_NR(3, 19), "spi_cs");
- gpio_direction_output(IMX_GPIO_NR(3, 19), 1);
- SETUP_IOMUX_PADS(ecspi1_pads);
-}
-#endif
-
-/* configure eth0 PHY board-specific LED behavior */
-int board_phy_config(struct phy_device *phydev)
-{
- unsigned short val;
-
- /* Marvel 88E1510 */
- if (phydev->phy_id == 0x1410dd1) {
- /*
- * Page 3, Register 16: LED[2:0] Function Control Register
- * LED[0] (SPD:Amber) R16_3.3:0 to 0111: on-GbE link
- * LED[1] (LNK:Green) R16_3.7:4 to 0001: on-link, blink-activity
- */
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 3);
- val = phy_read(phydev, MDIO_DEVAD_NONE, 16);
- val &= 0xff00;
- val |= 0x0017;
- phy_write(phydev, MDIO_DEVAD_NONE, 16, val);
- phy_write(phydev, MDIO_DEVAD_NONE, 22, 0);
- }
-
- /* TI DP83867 */
- else if (phydev->phy_id == 0x2000a231) {
- /* configure register 0x170 for ref CLKOUT */
- phy_write(phydev, MDIO_DEVAD_NONE, 13, 0x001f);
- phy_write(phydev, MDIO_DEVAD_NONE, 14, 0x0170);
- phy_write(phydev, MDIO_DEVAD_NONE, 13, 0x401f);
- val = phy_read(phydev, MDIO_DEVAD_NONE, 14);
- val &= ~0x1f00;
- val |= 0x0b00; /* chD tx clock*/
- phy_write(phydev, MDIO_DEVAD_NONE, 14, val);
- }
-
- if (phydev->drv->config)
- phydev->drv->config(phydev);
-
- return 0;
-}
-
-#ifdef CONFIG_MV88E61XX_SWITCH
-int mv88e61xx_hw_reset(struct phy_device *phydev)
-{
- struct mii_dev *bus = phydev->bus;
-
- /* GPIO[0] output, CLK125 */
- debug("enabling RGMII_REFCLK\n");
- bus->write(bus, 0x1c /*MV_GLOBAL2*/, 0,
- 0x1a /*MV_SCRATCH_MISC*/,
- (1 << 15) | (0x62 /*MV_GPIO_DIR*/ << 8) | 0xfe);
- bus->write(bus, 0x1c /*MV_GLOBAL2*/, 0,
- 0x1a /*MV_SCRATCH_MISC*/,
- (1 << 15) | (0x68 /*MV_GPIO01_CNTL*/ << 8) | 7);
-
- /* RGMII delay - Physical Control register bit[15:14] */
- debug("setting port%d RGMII rx/tx delay\n", CONFIG_MV88E61XX_CPU_PORT);
- /* forced 1000mbps full-duplex link */
- bus->write(bus, 0x10 + CONFIG_MV88E61XX_CPU_PORT, 0, 1, 0xc0fe);
- phydev->autoneg = AUTONEG_DISABLE;
- phydev->speed = SPEED_1000;
- phydev->duplex = DUPLEX_FULL;
-
- /* LED configuration: 7:4-green (8=Activity) 3:0 amber (9=10Link) */
- bus->write(bus, 0x10, 0, 0x16, 0x8089);
- bus->write(bus, 0x11, 0, 0x16, 0x8089);
- bus->write(bus, 0x12, 0, 0x16, 0x8089);
- bus->write(bus, 0x13, 0, 0x16, 0x8089);
-
- return 0;
-}
-#endif // CONFIG_MV88E61XX_SWITCH
-
-int board_eth_init(bd_t *bis)
-{
-#ifdef CONFIG_FEC_MXC
- struct ventana_board_info *info = &ventana_info;
-
- if (test_bit(EECONFIG_ETH0, info->config)) {
- setup_iomux_enet(GP_PHY_RST);
- cpu_eth_init(bis);
- }
-#endif
-
-#ifdef CONFIG_E1000
- e1000_initialize(bis);
-#endif
-
-#ifdef CONFIG_CI_UDC
- /* For otg ethernet*/
- usb_eth_initialize(bis);
-#endif
-
- /* default to the first detected enet dev */
- if (!env_get("ethprime")) {
- struct eth_device *dev = eth_get_dev_by_index(0);
- if (dev) {
- env_set("ethprime", dev->name);
- printf("set ethprime to %s\n", env_get("ethprime"));
- }
- }
-
- return 0;
-}
-
-#if defined(CONFIG_VIDEO_IPUV3)
-
-static void enable_hdmi(struct display_info_t const *dev)
-{
- imx_enable_hdmi_phy();
-}
-
-static int detect_i2c(struct display_info_t const *dev)
-{
- return i2c_set_bus_num(dev->bus) == 0 &&
- i2c_probe(dev->addr) == 0;
-}
-
-static void enable_lvds(struct display_info_t const *dev)
-{
- struct iomuxc *iomux = (struct iomuxc *)
- IOMUXC_BASE_ADDR;
-
- /* set CH0 data width to 24bit (IOMUXC_GPR2:5 0=18bit, 1=24bit) */
- u32 reg = readl(&iomux->gpr[2]);
- reg |= IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT;
- writel(reg, &iomux->gpr[2]);
-
- /* Enable Backlight */
- gpio_request(IMX_GPIO_NR(1, 10), "bklt_gpio");
- gpio_direction_output(IMX_GPIO_NR(1, 10), 0);
- gpio_request(IMX_GPIO_NR(1, 18), "bklt_en");
- SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 | DIO_PAD_CFG);
- gpio_direction_output(IMX_GPIO_NR(1, 18), 1);
-}
-
-struct display_info_t const displays[] = {{
- /* HDMI Output */
- .bus = -1,
- .addr = 0,
- .pixfmt = IPU_PIX_FMT_RGB24,
- .detect = detect_hdmi,
- .enable = enable_hdmi,
- .mode = {
- .name = "HDMI",
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15385,
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} }, {
- /* Freescale MXC-LVDS1: HannStar HSD100PXN1-A00 w/ egalx_ts cont */
- .bus = 2,
- .addr = 0x4,
- .pixfmt = IPU_PIX_FMT_LVDS666,
- .detect = detect_i2c,
- .enable = enable_lvds,
- .mode = {
- .name = "Hannstar-XGA",
- .refresh = 60,
- .xres = 1024,
- .yres = 768,
- .pixclock = 15385,
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} }, {
- /* DLC700JMG-T-4 */
- .bus = 0,
- .addr = 0,
- .detect = NULL,
- .enable = enable_lvds,
- .pixfmt = IPU_PIX_FMT_LVDS666,
- .mode = {
- .name = "DLC700JMGT4",
- .refresh = 60,
- .xres = 1024, /* 1024x600active pixels */
- .yres = 600,
- .pixclock = 15385, /* 64MHz */
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} }, {
- /* DLC800FIG-T-3 */
- .bus = 0,
- .addr = 0,
- .detect = NULL,
- .enable = enable_lvds,
- .pixfmt = IPU_PIX_FMT_LVDS666,
- .mode = {
- .name = "DLC800FIGT3",
- .refresh = 60,
- .xres = 1024, /* 1024x768 active pixels */
- .yres = 768,
- .pixclock = 15385, /* 64MHz */
- .left_margin = 220,
- .right_margin = 40,
- .upper_margin = 21,
- .lower_margin = 7,
- .hsync_len = 60,
- .vsync_len = 10,
- .sync = FB_SYNC_EXT,
- .vmode = FB_VMODE_NONINTERLACED
-} } };
-size_t display_count = ARRAY_SIZE(displays);
-
-static void setup_display(void)
-{
- struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
- struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
- int reg;
-
- enable_ipu_clock();
- imx_setup_hdmi();
- /* Turn on LDB0,IPU,IPU DI0 clocks */
- reg = __raw_readl(&mxc_ccm->CCGR3);
- reg |= MXC_CCM_CCGR3_LDB_DI0_MASK;
- writel(reg, &mxc_ccm->CCGR3);
-
- /* set LDB0, LDB1 clk select to 011/011 */
- reg = readl(&mxc_ccm->cs2cdr);
- reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK
- |MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
- reg |= (3<<MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET)
- |(3<<MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->cs2cdr);
-
- reg = readl(&mxc_ccm->cscmr2);
- reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV;
- writel(reg, &mxc_ccm->cscmr2);
-
- reg = readl(&mxc_ccm->chsccdr);
- reg |= (CHSCCDR_CLK_SEL_LDB_DI0
- <<MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
- writel(reg, &mxc_ccm->chsccdr);
-
- reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
- |IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
- |IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
- |IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
- |IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT
- |IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
- |IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT
- |IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED
- |IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
- writel(reg, &iomux->gpr[2]);
-
- reg = readl(&iomux->gpr[3]);
- reg = (reg & ~IOMUXC_GPR3_LVDS0_MUX_CTL_MASK)
- | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
- <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET);
- writel(reg, &iomux->gpr[3]);
-
- /* LVDS Backlight GPIO on LVDS connector - output low */
- SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 | DIO_PAD_CFG);
- gpio_direction_output(IMX_GPIO_NR(1, 10), 0);
-}
-#endif /* CONFIG_VIDEO_IPUV3 */
-
-/* setup board specific PMIC */
-int power_init_board(void)
-{
- setup_pmic();
- return 0;
-}
-
-#if defined(CONFIG_CMD_PCI)
-int imx6_pcie_toggle_reset(void)
-{
- if (board_type < GW_UNKNOWN) {
- uint pin = gpio_cfg[board_type].pcie_rst;
- gpio_request(pin, "pci_rst#");
- gpio_direction_output(pin, 0);
- mdelay(50);
- gpio_direction_output(pin, 1);
- }
- return 0;
-}
-
-/*
- * Most Ventana boards have a PLX PEX860x PCIe switch onboard and use its
- * GPIO's as PERST# signals for its downstream ports - configure the GPIO's
- * properly and assert reset for 100ms.
- */
-#define MAX_PCI_DEVS 32
-struct pci_dev {
- pci_dev_t devfn;
- unsigned short vendor;
- unsigned short device;
- unsigned short class;
- unsigned short busno; /* subbordinate busno */
- struct pci_dev *ppar;
-};
-struct pci_dev pci_devs[MAX_PCI_DEVS];
-int pci_devno;
-int pci_bridgeno;
-
-void board_pci_fixup_dev(struct pci_controller *hose, pci_dev_t dev,
- unsigned short vendor, unsigned short device,
- unsigned short class)
-{
- int i;
- u32 dw;
- struct pci_dev *pdev = &pci_devs[pci_devno++];
-
- debug("%s: %02d:%02d.%02d: %04x:%04x\n", __func__,
- PCI_BUS(dev), PCI_DEV(dev), PCI_FUNC(dev), vendor, device);
-
- /* store array of devs for later use in device-tree fixup */
- pdev->devfn = dev;
- pdev->vendor = vendor;
- pdev->device = device;
- pdev->class = class;
- pdev->ppar = NULL;
- if (class == PCI_CLASS_BRIDGE_PCI)
- pdev->busno = ++pci_bridgeno;
- else
- pdev->busno = 0;
-
- /* fixup RC - it should be 00:00.0 not 00:01.0 */
- if (PCI_BUS(dev) == 0)
- pdev->devfn = 0;
-
- /* find dev's parent */
- for (i = 0; i < pci_devno; i++) {
- if (pci_devs[i].busno == PCI_BUS(pdev->devfn)) {
- pdev->ppar = &pci_devs[i];
- break;
- }
- }
-
- /* assert downstream PERST# */
- if (vendor == PCI_VENDOR_ID_PLX &&
- (device & 0xfff0) == 0x8600 &&
- PCI_DEV(dev) == 0 && PCI_FUNC(dev) == 0) {
- debug("configuring PLX 860X downstream PERST#\n");
- pci_hose_read_config_dword(hose, dev, 0x62c, &dw);
- dw |= 0xaaa8; /* GPIO1-7 outputs */
- pci_hose_write_config_dword(hose, dev, 0x62c, dw);
-
- pci_hose_read_config_dword(hose, dev, 0x644, &dw);
- dw |= 0xfe; /* GPIO1-7 output high */
- pci_hose_write_config_dword(hose, dev, 0x644, dw);
-
- mdelay(100);
- }
-}
-#endif /* CONFIG_CMD_PCI */
-
-#ifdef CONFIG_SERIAL_TAG
-/*
- * called when setting up ATAGS before booting kernel
- * populate serialnum from the following (in order of priority):
- * serial# env var
- * eeprom
- */
-void get_board_serial(struct tag_serialnr *serialnr)
-{
- char *serial = env_get("serial#");
-
- if (serial) {
- serialnr->high = 0;
- serialnr->low = simple_strtoul(serial, NULL, 10);
- } else if (ventana_info.model[0]) {
- serialnr->high = 0;
- serialnr->low = ventana_info.serial;
- } else {
- serialnr->high = 0;
- serialnr->low = 0;
- }
-}
-#endif
-
-/*
- * Board Support
- */
-
-int board_early_init_f(void)
-{
- setup_iomux_uart();
-
-#if defined(CONFIG_VIDEO_IPUV3)
- setup_display();
-#endif
- return 0;
-}
-
-int dram_init(void)
-{
- gd->ram_size = imx_ddr_size();
- return 0;
-}
-
-int board_init(void)
-{
- struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
- clrsetbits_le32(&iomuxc_regs->gpr[1],
- IOMUXC_GPR1_OTG_ID_MASK,
- IOMUXC_GPR1_OTG_ID_GPIO1);
-
- /* address of linux boot parameters */
- gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-#ifdef CONFIG_CMD_NAND
- setup_gpmi_nand();
-#endif
-#ifdef CONFIG_MXC_SPI
- setup_spi();
-#endif
- setup_ventana_i2c();
-
-#ifdef CONFIG_SATA
- setup_sata();
-#endif
- /* read Gateworks EEPROM into global struct (used later) */
- board_type = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
-
- setup_iomux_gpio(board_type, &ventana_info);
-
- return 0;
-}
-
-#if defined(CONFIG_DISPLAY_BOARDINFO_LATE)
-/*
- * called during late init (after relocation and after board_init())
- * by virtue of CONFIG_DISPLAY_BOARDINFO_LATE as we needed i2c initialized and
- * EEPROM read.
- */
-int checkboard(void)
-{
- struct ventana_board_info *info = &ventana_info;
- unsigned char buf[4];
- const char *p;
- int quiet; /* Quiet or minimal output mode */
-
- quiet = 0;
- p = env_get("quiet");
- if (p)
- quiet = simple_strtol(p, NULL, 10);
- else
- env_set("quiet", "0");
-
- puts("\nGateworks Corporation Copyright 2014\n");
- if (info->model[0]) {
- printf("Model: %s\n", info->model);
- printf("MFGDate: %02x-%02x-%02x%02x\n",
- info->mfgdate[0], info->mfgdate[1],
- info->mfgdate[2], info->mfgdate[3]);
- printf("Serial:%d\n", info->serial);
- } else {
- puts("Invalid EEPROM - board will not function fully\n");
- }
- if (quiet)
- return 0;
-
- /* Display GSC firmware revision/CRC/status */
- gsc_info(0);
-
- /* Display RTC */
- if (!gsc_i2c_read(GSC_RTC_ADDR, 0x00, 1, buf, 4)) {
- printf("RTC: %d\n",
- buf[0] | buf[1]<<8 | buf[2]<<16 | buf[3]<<24);
- }
-
- return 0;
-}
-#endif
-
-#ifdef CONFIG_CMD_BMODE
-/*
- * BOOT_CFG1, BOOT_CFG2, BOOT_CFG3, BOOT_CFG4
- * see Table 8-11 and Table 5-9
- * BOOT_CFG1[7] = 1 (boot from NAND)
- * BOOT_CFG1[5] = 0 - raw NAND
- * BOOT_CFG1[4] = 0 - default pad settings
- * BOOT_CFG1[3:2] = 00 - devices = 1
- * BOOT_CFG1[1:0] = 00 - Row Address Cycles = 3
- * BOOT_CFG2[4:3] = 00 - Boot Search Count = 2
- * BOOT_CFG2[2:1] = 01 - Pages In Block = 64
- * BOOT_CFG2[0] = 0 - Reset time 12ms
- */
-static const struct boot_mode board_boot_modes[] = {
- /* NAND: 64pages per block, 3 row addr cycles, 2 copies of FCB/DBBT */
- { "nand", MAKE_CFGVAL(0x80, 0x02, 0x00, 0x00) },
- { "emmc2", MAKE_CFGVAL(0x60, 0x48, 0x00, 0x00) }, /* GW5600 */
- { "emmc3", MAKE_CFGVAL(0x60, 0x50, 0x00, 0x00) }, /* GW5903/GW5904 */
- { NULL, 0 },
-};
-#endif
-
-/* late init */
-int misc_init_r(void)
-{
- struct ventana_board_info *info = &ventana_info;
- char buf[256];
- int i;
-
- /* set env vars based on EEPROM data */
- if (ventana_info.model[0]) {
- char str[16], fdt[36];
- char *p;
- const char *cputype = "";
-
- /*
- * FDT name will be prefixed with CPU type. Three versions
- * will be created each increasingly generic and bootloader
- * env scripts will try loading each from most specific to
- * least.
- */
- if (is_cpu_type(MXC_CPU_MX6Q) ||
- is_cpu_type(MXC_CPU_MX6D))
- cputype = "imx6q";
- else if (is_cpu_type(MXC_CPU_MX6DL) ||
- is_cpu_type(MXC_CPU_MX6SOLO))
- cputype = "imx6dl";
- env_set("soctype", cputype);
- if (8 << (ventana_info.nand_flash_size-1) >= 2048)
- env_set("flash_layout", "large");
- else
- env_set("flash_layout", "normal");
- memset(str, 0, sizeof(str));
- for (i = 0; i < (sizeof(str)-1) && info->model[i]; i++)
- str[i] = tolower(info->model[i]);
- env_set("model", str);
- if (!env_get("fdt_file")) {
- sprintf(fdt, "%s-%s.dtb", cputype, str);
- env_set("fdt_file", fdt);
- }
- p = strchr(str, '-');
- if (p) {
- *p++ = 0;
-
- env_set("model_base", str);
- sprintf(fdt, "%s-%s.dtb", cputype, str);
- env_set("fdt_file1", fdt);
- if (board_type != GW551x &&
- board_type != GW552x &&
- board_type != GW553x &&
- board_type != GW560x)
- str[4] = 'x';
- str[5] = 'x';
- str[6] = 0;
- sprintf(fdt, "%s-%s.dtb", cputype, str);
- env_set("fdt_file2", fdt);
- }
-
- /* initialize env from EEPROM */
- if (test_bit(EECONFIG_ETH0, info->config) &&
- !env_get("ethaddr")) {
- eth_env_set_enetaddr("ethaddr", info->mac0);
- }
- if (test_bit(EECONFIG_ETH1, info->config) &&
- !env_get("eth1addr")) {
- eth_env_set_enetaddr("eth1addr", info->mac1);
- }
-
- /* board serial-number */
- sprintf(str, "%6d", info->serial);
- env_set("serial#", str);
-
- /* memory MB */
- sprintf(str, "%d", (int) (gd->ram_size >> 20));
- env_set("mem_mb", str);
- }
-
- /* Set a non-initialized hwconfig based on board configuration */
- if (!strcmp(env_get("hwconfig"), "_UNKNOWN_")) {
- buf[0] = 0;
- if (gpio_cfg[board_type].rs232_en)
- strcat(buf, "rs232;");
- for (i = 0; i < gpio_cfg[board_type].dio_num; i++) {
- char buf1[32];
- sprintf(buf1, "dio%d:mode=gpio;", i);
- if (strlen(buf) + strlen(buf1) < sizeof(buf))
- strcat(buf, buf1);
- }
- env_set("hwconfig", buf);
- }
-
- /* setup baseboard specific GPIO based on board and env */
- setup_board_gpio(board_type, info);
-
-#ifdef CONFIG_CMD_BMODE
- add_board_boot_modes(board_boot_modes);
-#endif
-
- /* disable boot watchdog */
- gsc_boot_wd_disable();
-
- return 0;
-}
-
-#ifdef CONFIG_OF_BOARD_SETUP
-
-static int ft_sethdmiinfmt(void *blob, char *mode)
-{
- int off;
-
- if (!mode)
- return -EINVAL;
-
- off = fdt_node_offset_by_compatible(blob, -1, "nxp,tda1997x");
- if (off < 0)
- return off;
-
- if (0 == strcasecmp(mode, "yuv422bt656")) {
- u8 cfg[] = { 0x00, 0x00, 0x00, 0x82, 0x81, 0x00,
- 0x00, 0x00, 0x00 };
- mode = "422_ccir";
- fdt_setprop(blob, off, "vidout_fmt", mode, strlen(mode) + 1);
- fdt_setprop_u32(blob, off, "vidout_trc", 1);
- fdt_setprop_u32(blob, off, "vidout_blc", 1);
- fdt_setprop(blob, off, "vidout_portcfg", cfg, sizeof(cfg));
- printf(" set HDMI input mode to %s\n", mode);
- } else if (0 == strcasecmp(mode, "yuv422smp")) {
- u8 cfg[] = { 0x00, 0x00, 0x00, 0x88, 0x87, 0x00,
- 0x82, 0x81, 0x00 };
- mode = "422_smp";
- fdt_setprop(blob, off, "vidout_fmt", mode, strlen(mode) + 1);
- fdt_setprop_u32(blob, off, "vidout_trc", 0);
- fdt_setprop_u32(blob, off, "vidout_blc", 0);
- fdt_setprop(blob, off, "vidout_portcfg", cfg, sizeof(cfg));
- printf(" set HDMI input mode to %s\n", mode);
- } else {
- return -EINVAL;
- }
-
- return 0;
-}
-
-/* enable a property of a node if the node is found */
-static inline void ft_enable_path(void *blob, const char *path)
-{
- int i = fdt_path_offset(blob, path);
- if (i >= 0) {
- debug("enabling %s\n", path);
- fdt_status_okay(blob, i);
- }
-}
-
-/* remove a property of a node if the node is found */
-static inline void ft_delprop_path(void *blob, const char *path,
- const char *name)
-{
- int i = fdt_path_offset(blob, path);
- if (i) {
- debug("removing %s/%s\n", path, name);
- fdt_delprop(blob, i, name);
- }
-}
-
-#if defined(CONFIG_CMD_PCI)
-#define PCI_ID(x) ( \
- (PCI_BUS(x->devfn)<<16)| \
- (PCI_DEV(x->devfn)<<11)| \
- (PCI_FUNC(x->devfn)<<8) \
- )
-#define PCIE_PATH "/soc/pcie@0x01000000"
-int fdt_add_pci_node(void *blob, int par, struct pci_dev *dev)
-{
- uint32_t reg[5];
- char node[32];
- int np;
-
- sprintf(node, "pcie@%d,%d,%d", PCI_BUS(dev->devfn),
- PCI_DEV(dev->devfn), PCI_FUNC(dev->devfn));
-
- np = fdt_subnode_offset(blob, par, node);
- if (np >= 0)
- return np;
- np = fdt_add_subnode(blob, par, node);
- if (np < 0) {
- printf(" %s failed: no space\n", __func__);
- return np;
- }
-
- memset(reg, 0, sizeof(reg));
- reg[0] = cpu_to_fdt32(PCI_ID(dev));
- fdt_setprop(blob, np, "reg", reg, sizeof(reg));
-
- return np;
-}
-
-/* build a path of nested PCI devs for all bridges passed through */
-int fdt_add_pci_path(void *blob, struct pci_dev *dev)
-{
- struct pci_dev *bridges[MAX_PCI_DEVS];
- int k, np;
-
- /* build list of parents */
- np = fdt_path_offset(blob, PCIE_PATH);
- if (np < 0)
- return np;
-
- k = 0;
- while (dev) {
- bridges[k++] = dev;
- dev = dev->ppar;
- };
-
- /* now add them the to DT in reverse order */
- while (k--) {
- np = fdt_add_pci_node(blob, np, bridges[k]);
- if (np < 0)
- break;
- }
-
- return np;
-}
-
-/*
- * The GW16082 has a hardware errata errata such that it's
- * INTA/B/C/D are mis-mapped to its four slots (slot12-15). Because
- * of this normal PCI interrupt swizzling will not work so we will
- * provide an irq-map via device-tree.
- */
-int fdt_fixup_gw16082(void *blob, int np, struct pci_dev *dev)
-{
- int len;
- int host;
- uint32_t imap_new[8*4*4];
- const uint32_t *imap;
- uint32_t irq[4];
- uint32_t reg[4];
- int i;
-
- /* build irq-map based on host controllers map */
- host = fdt_path_offset(blob, PCIE_PATH);
- if (host < 0) {
- printf(" %s failed: missing host\n", __func__);
- return host;
- }
-
- /* use interrupt data from root complex's node */
- imap = fdt_getprop(blob, host, "interrupt-map", &len);
- if (!imap || len != 128) {
- printf(" %s failed: invalid interrupt-map\n",
- __func__);
- return -FDT_ERR_NOTFOUND;
- }
-
- /* obtain irq's of host controller in pin order */
- for (i = 0; i < 4; i++)
- irq[(fdt32_to_cpu(imap[(i*8)+3])-1)%4] = imap[(i*8)+6];
-
- /*
- * determine number of swizzles necessary:
- * For each bridge we pass through we need to swizzle
- * the number of the slot we are on.
- */
- struct pci_dev *d;
- int b;
- b = 0;
- d = dev->ppar;
- while(d && d->ppar) {
- b += PCI_DEV(d->devfn);
- d = d->ppar;
- }
-
- /* create new irq mappings for slots12-15
- * <skt> <idsel> <slot> <skt-inta> <skt-intb>
- * J3 AD28 12 INTD INTA
- * J4 AD29 13 INTC INTD
- * J5 AD30 14 INTB INTC
- * J2 AD31 15 INTA INTB
- */
- for (i = 0; i < 4; i++) {
- /* addr matches bus:dev:func */
- u32 addr = dev->busno << 16 | (12+i) << 11;
-
- /* default cells from root complex */
- memcpy(&imap_new[i*32], imap, 128);
- /* first cell is PCI device address (BDF) */
- imap_new[(i*32)+(0*8)+0] = cpu_to_fdt32(addr);
- imap_new[(i*32)+(1*8)+0] = cpu_to_fdt32(addr);
- imap_new[(i*32)+(2*8)+0] = cpu_to_fdt32(addr);
- imap_new[(i*32)+(3*8)+0] = cpu_to_fdt32(addr);
- /* third cell is pin */
- imap_new[(i*32)+(0*8)+3] = cpu_to_fdt32(1);
- imap_new[(i*32)+(1*8)+3] = cpu_to_fdt32(2);
- imap_new[(i*32)+(2*8)+3] = cpu_to_fdt32(3);
- imap_new[(i*32)+(3*8)+3] = cpu_to_fdt32(4);
- /* sixth cell is relative interrupt */
- imap_new[(i*32)+(0*8)+6] = irq[(15-(12+i)+b+0)%4];
- imap_new[(i*32)+(1*8)+6] = irq[(15-(12+i)+b+1)%4];
- imap_new[(i*32)+(2*8)+6] = irq[(15-(12+i)+b+2)%4];
- imap_new[(i*32)+(3*8)+6] = irq[(15-(12+i)+b+3)%4];
- }
- fdt_setprop(blob, np, "interrupt-map", imap_new,
- sizeof(imap_new));
- reg[0] = cpu_to_fdt32(0xfff00);
- reg[1] = 0;
- reg[2] = 0;
- reg[3] = cpu_to_fdt32(0x7);
- fdt_setprop(blob, np, "interrupt-map-mask", reg, sizeof(reg));
- fdt_setprop_cell(blob, np, "#interrupt-cells", 1);
- fdt_setprop_string(blob, np, "device_type", "pci");
- fdt_setprop_cell(blob, np, "#address-cells", 3);
- fdt_setprop_cell(blob, np, "#size-cells", 2);
- printf(" Added custom interrupt-map for GW16082\n");
-
- return 0;
-}
-
-/* The sky2 GigE MAC obtains it's MAC addr from device-tree by default */
-int fdt_fixup_sky2(void *blob, int np, struct pci_dev *dev)
-{
- char *tmp, *end;
- char mac[16];
- unsigned char mac_addr[6];
- int j;
-
- sprintf(mac, "eth1addr");
- tmp = env_get(mac);
- if (tmp) {
- for (j = 0; j < 6; j++) {
- mac_addr[j] = tmp ?
- simple_strtoul(tmp, &end,16) : 0;
- if (tmp)
- tmp = (*end) ? end+1 : end;
- }
- fdt_setprop(blob, np, "local-mac-address", mac_addr,
- sizeof(mac_addr));
- printf(" Added mac addr for eth1\n");
- return 0;
- }
-
- return -1;
-}
-
-/*
- * PCI DT nodes must be nested therefore if we need to apply a DT fixup
- * we will walk the PCI bus and add bridge nodes up to the device receiving
- * the fixup.
- */
-void ft_board_pci_fixup(void *blob, bd_t *bd)
-{
- int i, np;
- struct pci_dev *dev;
-
- for (i = 0; i < pci_devno; i++) {
- dev = &pci_devs[i];
-
- /*
- * The GW16082 consists of a TI XIO2001 PCIe-to-PCI bridge and
- * an EEPROM@i2c1-0x50.
- */
- if ((dev->vendor == PCI_VENDOR_ID_TI) &&
- (dev->device == 0x8240) &&
- (i2c_set_bus_num(1) == 0) &&
- (i2c_probe(0x50) == 0))
- {
- np = fdt_add_pci_path(blob, dev);
- if (np > 0)
- fdt_fixup_gw16082(blob, np, dev);
- }
-
- /* ethernet1 mac address */
- else if ((dev->vendor == PCI_VENDOR_ID_MARVELL) &&
- (dev->device == 0x4380))
- {
- np = fdt_add_pci_path(blob, dev);
- if (np > 0)
- fdt_fixup_sky2(blob, np, dev);
- }
- }
-}
-#endif /* if defined(CONFIG_CMD_PCI) */
-
-void ft_board_wdog_fixup(void *blob, const char *path)
-{
- ft_delprop_path(blob, path, "ext-reset-output");
- ft_delprop_path(blob, path, "fsl,ext-reset-output");
-}
-
-/*
- * called prior to booting kernel or by 'fdt boardsetup' command
- *
- * unless 'fdt_noauto' env var is set we will update the following in the DTB:
- * - mtd partitions based on mtdparts/mtdids env
- * - system-serial (board serial num from EEPROM)
- * - board (full model from EEPROM)
- * - peripherals removed from DTB if not loaded on board (per EEPROM config)
- */
-#define UART1_PATH "/soc/aips-bus at 02100000/serial at 021ec000"
-#define WDOG1_PATH "/soc/aips-bus at 02000000/wdog at 020bc000"
-#define WDOG2_PATH "/soc/aips-bus at 02000000/wdog at 020c0000"
-#define GPIO3_PATH "/soc/aips-bus at 02000000/gpio at 020a4000"
-int ft_board_setup(void *blob, bd_t *bd)
-{
- struct ventana_board_info *info = &ventana_info;
- struct ventana_eeprom_config *cfg;
- static const struct node_info nodes[] = {
- { "sst,w25q256", MTD_DEV_TYPE_NOR, }, /* SPI flash */
- { "fsl,imx6q-gpmi-nand", MTD_DEV_TYPE_NAND, }, /* NAND flash */
- };
- const char *model = env_get("model");
- const char *display = env_get("display");
- int i;
- char rev = 0;
-
- /* determine board revision */
- for (i = sizeof(ventana_info.model) - 1; i > 0; i--) {
- if (ventana_info.model[i] >= 'A') {
- rev = ventana_info.model[i];
- break;
- }
- }
-
- if (env_get("fdt_noauto")) {
- puts(" Skiping ft_board_setup (fdt_noauto defined)\n");
- return 0;
- }
-
- if (test_bit(EECONFIG_NAND, info->config)) {
- /* Update partition nodes using info from mtdparts env var */
- puts(" Updating MTD partitions...\n");
- fdt_fixup_mtdparts(blob, nodes, ARRAY_SIZE(nodes));
- }
-
- /* Update display timings from display env var */
- if (display) {
- if (fdt_fixup_display(blob, fdt_get_alias(blob, "lvds0"),
- display) >= 0)
- printf(" Set display timings for %s...\n", display);
- }
-
- printf(" Adjusting FDT per EEPROM for %s...\n", model);
-
- /* board serial number */
- fdt_setprop(blob, 0, "system-serial", env_get("serial#"),
- strlen(env_get("serial#")) + 1);
-
- /* board (model contains model from device-tree) */
- fdt_setprop(blob, 0, "board", info->model,
- strlen((const char *)info->model) + 1);
-
- /* set desired digital video capture format */
- ft_sethdmiinfmt(blob, env_get("hdmiinfmt"));
-
- /*
- * Board model specific fixups
- */
- switch (board_type) {
- case GW51xx:
- /*
- * disable wdog node for GW51xx-A/B to work around
- * errata causing wdog timer to be unreliable.
- */
- if (rev >= 'A' && rev < 'C') {
- i = fdt_path_offset(blob, WDOG1_PATH);
- if (i)
- fdt_status_disabled(blob, i);
- }
-
- /* GW51xx-E adds WDOG1_B external reset */
- if (rev < 'E')
- ft_board_wdog_fixup(blob, WDOG1_PATH);
- break;
-
- case GW52xx:
- /* GW522x Uses GPIO3_IO23 instead of GPIO1_IO29 */
- if (info->model[4] == '2') {
- u32 handle = 0;
- u32 *range = NULL;
-
- i = fdt_node_offset_by_compatible(blob, -1,
- "fsl,imx6q-pcie");
- if (i)
- range = (u32 *)fdt_getprop(blob, i,
- "reset-gpio", NULL);
-
- if (range) {
- i = fdt_path_offset(blob, GPIO3_PATH);
- if (i)
- handle = fdt_get_phandle(blob, i);
- if (handle) {
- range[0] = cpu_to_fdt32(handle);
- range[1] = cpu_to_fdt32(23);
- }
- }
-
- /* these have broken usd_vsel */
- if (strstr((const char *)info->model, "SP318-B") ||
- strstr((const char *)info->model, "SP331-B"))
- gpio_cfg[board_type].usd_vsel = 0;
-
- /* GW522x-B adds WDOG1_B external reset */
- ft_board_wdog_fixup(blob, WDOG1_PATH);
- }
-
- /* GW520x-E adds WDOG1_B external reset */
- else if (info->model[4] == '0' && rev < 'E')
- ft_board_wdog_fixup(blob, WDOG1_PATH);
- break;
-
- case GW53xx:
- /* GW53xx-E adds WDOG1_B external reset */
- if (rev < 'E')
- ft_board_wdog_fixup(blob, WDOG1_PATH);
- break;
-
- case GW54xx:
- /*
- * disable serial2 node for GW54xx for compatibility with older
- * 3.10.x kernel that improperly had this node enabled in the DT
- */
- i = fdt_path_offset(blob, UART1_PATH);
- if (i)
- fdt_del_node(blob, i);
-
- /* GW54xx-E adds WDOG2_B external reset */
- if (rev < 'E')
- ft_board_wdog_fixup(blob, WDOG2_PATH);
- break;
-
- case GW551x:
- /*
- * isolate CSI0_DATA_EN for GW551x-A to work around errata
- * causing non functional digital video in (it is not hooked up)
- */
- if (rev == 'A') {
- u32 *range = NULL;
- int len;
- const u32 *handle = NULL;
-
- i = fdt_node_offset_by_compatible(blob, -1,
- "fsl,imx-tda1997x-video");
- if (i)
- handle = fdt_getprop(blob, i, "pinctrl-0",
- NULL);
- if (handle)
- i = fdt_node_offset_by_phandle(blob,
- fdt32_to_cpu(*handle));
- if (i)
- range = (u32 *)fdt_getprop(blob, i, "fsl,pins",
- &len);
- if (range) {
- len /= sizeof(u32);
- for (i = 0; i < len; i += 6) {
- u32 mux_reg = fdt32_to_cpu(range[i+0]);
- u32 conf_reg = fdt32_to_cpu(range[i+1]);
- /* mux PAD_CSI0_DATA_EN to GPIO */
- if (is_cpu_type(MXC_CPU_MX6Q) &&
- mux_reg == 0x260 &&
- conf_reg == 0x630)
- range[i+3] = cpu_to_fdt32(0x5);
- else if (!is_cpu_type(MXC_CPU_MX6Q) &&
- mux_reg == 0x08c &&
- conf_reg == 0x3a0)
- range[i+3] = cpu_to_fdt32(0x5);
- }
- fdt_setprop_inplace(blob, i, "fsl,pins", range,
- len);
- }
-
- /* set BT656 video format */
- ft_sethdmiinfmt(blob, "yuv422bt656");
- }
-
- /* GW551x-C adds WDOG1_B external reset */
- if (rev < 'C')
- ft_board_wdog_fixup(blob, WDOG1_PATH);
- break;
- }
-
- /* Configure DIO */
- for (i = 0; i < gpio_cfg[board_type].dio_num; i++) {
- struct dio_cfg *cfg = &gpio_cfg[board_type].dio_cfg[i];
- char arg[10];
-
- sprintf(arg, "dio%d", i);
- if (!hwconfig(arg))
- continue;
- if (hwconfig_subarg_cmp(arg, "mode", "pwm") && cfg->pwm_param)
- {
- char path[48];
- sprintf(path, "/soc/aips-bus at 02000000/pwm@%08x",
- 0x02080000 + (0x4000 * (cfg->pwm_param - 1)));
- printf(" Enabling pwm%d for DIO%d\n",
- cfg->pwm_param, i);
- ft_enable_path(blob, path);
- }
- }
-
- /* remove no-1-8-v if UHS-I support is present */
- if (gpio_cfg[board_type].usd_vsel) {
- debug("Enabling UHS-I support\n");
- ft_delprop_path(blob, "/soc/aips-bus at 02100000/usdhc at 02198000",
- "no-1-8-v");
- }
-
-#if defined(CONFIG_CMD_PCI)
- if (!env_get("nopcifixup"))
- ft_board_pci_fixup(blob, bd);
-#endif
-
- /*
- * Peripheral Config:
- * remove nodes by alias path if EEPROM config tells us the
- * peripheral is not loaded on the board.
- */
- if (env_get("fdt_noconfig")) {
- puts(" Skiping periperhal config (fdt_noconfig defined)\n");
- return 0;
- }
- cfg = econfig;
- while (cfg->name) {
- if (!test_bit(cfg->bit, info->config)) {
- fdt_del_node_and_alias(blob, cfg->dtalias ?
- cfg->dtalias : cfg->name);
- }
- cfg++;
- }
-
- return 0;
-}
-#endif /* CONFIG_OF_BOARD_SETUP */
-
-static struct mxc_serial_platdata ventana_mxc_serial_plat = {
- .reg = (struct mxc_uart *)UART2_BASE,
-};
-
-U_BOOT_DEVICE(ventana_serial) = {
- .name = "serial_mxc",
- .platdata = &ventana_mxc_serial_plat,
-};
diff --git a/board/gateworks/gw_ventana/gw_ventana_spl.c b/board/gateworks/gw_ventana/gw_ventana_spl.c
deleted file mode 100644
index a6ac546e959..00000000000
--- a/board/gateworks/gw_ventana/gw_ventana_spl.c
+++ /dev/null
@@ -1,691 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014 Gateworks Corporation
- * Author: Tim Harvey <tharvey@gateworks.com>
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/mx6-ddr.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/mach-imx/boot_mode.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <environment.h>
-#include <i2c.h>
-#include <spl.h>
-
-#include "gsc.h"
-#include "common.h"
-
-#define RTT_NOM_120OHM /* use 120ohm Rtt_nom vs 60ohm (lower power) */
-#define GSC_EEPROM_DDR_SIZE 0x2B /* enum (512,1024,2048) MB */
-#define GSC_EEPROM_DDR_WIDTH 0x2D /* enum (32,64) bit */
-
-/* configure MX6Q/DUAL mmdc DDR io registers */
-struct mx6dq_iomux_ddr_regs mx6dq_ddr_ioregs = {
- /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
- .dram_sdclk_0 = 0x00020030,
- .dram_sdclk_1 = 0x00020030,
- .dram_cas = 0x00020030,
- .dram_ras = 0x00020030,
- .dram_reset = 0x00020030,
- /* SDCKE[0:1]: 100k pull-up */
- .dram_sdcke0 = 0x00003000,
- .dram_sdcke1 = 0x00003000,
- /* SDBA2: pull-up disabled */
- .dram_sdba2 = 0x00000000,
- /* SDODT[0:1]: 100k pull-up, 40 ohm */
- .dram_sdodt0 = 0x00003030,
- .dram_sdodt1 = 0x00003030,
- /* SDQS[0:7]: Differential input, 40 ohm */
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
-
- /* DQM[0:7]: Differential input, 40 ohm */
- .dram_dqm0 = 0x00020030,
- .dram_dqm1 = 0x00020030,
- .dram_dqm2 = 0x00020030,
- .dram_dqm3 = 0x00020030,
- .dram_dqm4 = 0x00020030,
- .dram_dqm5 = 0x00020030,
- .dram_dqm6 = 0x00020030,
- .dram_dqm7 = 0x00020030,
-};
-
-/* configure MX6Q/DUAL mmdc GRP io registers */
-struct mx6dq_iomux_grp_regs mx6dq_grp_ioregs = {
- /* DDR3 */
- .grp_ddr_type = 0x000c0000,
- .grp_ddrmode_ctl = 0x00020000,
- /* disable DDR pullups */
- .grp_ddrpke = 0x00000000,
- /* ADDR[00:16], SDBA[0:1]: 40 ohm */
- .grp_addds = 0x00000030,
- /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
- .grp_ctlds = 0x00000030,
- /* DATA[00:63]: Differential input, 40 ohm */
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_b2ds = 0x00000030,
- .grp_b3ds = 0x00000030,
- .grp_b4ds = 0x00000030,
- .grp_b5ds = 0x00000030,
- .grp_b6ds = 0x00000030,
- .grp_b7ds = 0x00000030,
-};
-
-/* configure MX6SOLO/DUALLITE mmdc DDR io registers */
-struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
- /* SDCLK[0:1], CAS, RAS, Reset: Differential input, 40ohm */
- .dram_sdclk_0 = 0x00020030,
- .dram_sdclk_1 = 0x00020030,
- .dram_cas = 0x00020030,
- .dram_ras = 0x00020030,
- .dram_reset = 0x00020030,
- /* SDCKE[0:1]: 100k pull-up */
- .dram_sdcke0 = 0x00003000,
- .dram_sdcke1 = 0x00003000,
- /* SDBA2: pull-up disabled */
- .dram_sdba2 = 0x00000000,
- /* SDODT[0:1]: 100k pull-up, 40 ohm */
- .dram_sdodt0 = 0x00003030,
- .dram_sdodt1 = 0x00003030,
- /* SDQS[0:7]: Differential input, 40 ohm */
- .dram_sdqs0 = 0x00000030,
- .dram_sdqs1 = 0x00000030,
- .dram_sdqs2 = 0x00000030,
- .dram_sdqs3 = 0x00000030,
- .dram_sdqs4 = 0x00000030,
- .dram_sdqs5 = 0x00000030,
- .dram_sdqs6 = 0x00000030,
- .dram_sdqs7 = 0x00000030,
-
- /* DQM[0:7]: Differential input, 40 ohm */
- .dram_dqm0 = 0x00020030,
- .dram_dqm1 = 0x00020030,
- .dram_dqm2 = 0x00020030,
- .dram_dqm3 = 0x00020030,
- .dram_dqm4 = 0x00020030,
- .dram_dqm5 = 0x00020030,
- .dram_dqm6 = 0x00020030,
- .dram_dqm7 = 0x00020030,
-};
-
-/* configure MX6SOLO/DUALLITE mmdc GRP io registers */
-struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
- /* DDR3 */
- .grp_ddr_type = 0x000c0000,
- /* SDQS[0:7]: Differential input, 40 ohm */
- .grp_ddrmode_ctl = 0x00020000,
- /* disable DDR pullups */
- .grp_ddrpke = 0x00000000,
- /* ADDR[00:16], SDBA[0:1]: 40 ohm */
- .grp_addds = 0x00000030,
- /* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 40 ohm */
- .grp_ctlds = 0x00000030,
- /* DATA[00:63]: Differential input, 40 ohm */
- .grp_ddrmode = 0x00020000,
- .grp_b0ds = 0x00000030,
- .grp_b1ds = 0x00000030,
- .grp_b2ds = 0x00000030,
- .grp_b3ds = 0x00000030,
- .grp_b4ds = 0x00000030,
- .grp_b5ds = 0x00000030,
- .grp_b6ds = 0x00000030,
- .grp_b7ds = 0x00000030,
-};
-
-/* MT41K64M16JT-125 (1Gb density) */
-static struct mx6_ddr3_cfg mt41k64m16jt_125 = {
- .mem_speed = 1600,
- .density = 1,
- .width = 16,
- .banks = 8,
- .rowaddr = 13,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-/* MT41K128M16JT-125 (2Gb density) */
-static struct mx6_ddr3_cfg mt41k128m16jt_125 = {
- .mem_speed = 1600,
- .density = 2,
- .width = 16,
- .banks = 8,
- .rowaddr = 14,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-/* MT41K256M16HA-125 (4Gb density) */
-static struct mx6_ddr3_cfg mt41k256m16ha_125 = {
- .mem_speed = 1600,
- .density = 4,
- .width = 16,
- .banks = 8,
- .rowaddr = 15,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-/* MT41K512M16HA-125 (8Gb density) */
-static struct mx6_ddr3_cfg mt41k512m16ha_125 = {
- .mem_speed = 1600,
- .density = 8,
- .width = 16,
- .banks = 8,
- .rowaddr = 16,
- .coladdr = 10,
- .pagesz = 2,
- .trcd = 1375,
- .trcmin = 4875,
- .trasmin = 3500,
-};
-
-/*
- * calibration - these are the various CPU/DDR3 combinations we support
- */
-static struct mx6_mmdc_calibration mx6sdl_64x16_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x004C004E,
- .p0_mpwldectrl1 = 0x00440044,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x42440247,
- .p0_mpdgctrl1 = 0x02310232,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x45424746,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x33382C31,
-};
-
-static struct mx6_mmdc_calibration mx6dq_256x16_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x001B0016,
- .p0_mpwldectrl1 = 0x000C000E,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x4324033A,
- .p0_mpdgctrl1 = 0x00000000,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x40403438,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x40403D36,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_256x16_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00420043,
- .p0_mpwldectrl1 = 0x0016001A,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x4238023B,
- .p0_mpdgctrl1 = 0x00000000,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x40404849,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x40402E2F,
-};
-
-static struct mx6_mmdc_calibration mx6dq_128x32_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00190017,
- .p0_mpwldectrl1 = 0x00140026,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43380347,
- .p0_mpdgctrl1 = 0x433C034D,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x3C313539,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x36393C39,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_128x32_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x003C003C,
- .p0_mpwldectrl1 = 0x001F002A,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x42410244,
- .p0_mpdgctrl1 = 0x4234023A,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x484A4C4B,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x33342B32,
-};
-
-static struct mx6_mmdc_calibration mx6dq_128x64_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00190017,
- .p0_mpwldectrl1 = 0x00140026,
- .p1_mpwldectrl0 = 0x0021001C,
- .p1_mpwldectrl1 = 0x0011001D,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43380347,
- .p0_mpdgctrl1 = 0x433C034D,
- .p1_mpdgctrl0 = 0x032C0324,
- .p1_mpdgctrl1 = 0x03310232,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x3C313539,
- .p1_mprddlctl = 0x37343141,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x36393C39,
- .p1_mpwrdlctl = 0x42344438,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_128x64_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x003C003C,
- .p0_mpwldectrl1 = 0x001F002A,
- .p1_mpwldectrl0 = 0x00330038,
- .p1_mpwldectrl1 = 0x0022003F,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x42410244,
- .p0_mpdgctrl1 = 0x4234023A,
- .p1_mpdgctrl0 = 0x022D022D,
- .p1_mpdgctrl1 = 0x021C0228,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x484A4C4B,
- .p1_mprddlctl = 0x4B4D4E4B,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x33342B32,
- .p1_mpwrdlctl = 0x3933332B,
-};
-
-static struct mx6_mmdc_calibration mx6dq_256x32_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x001E001A,
- .p0_mpwldectrl1 = 0x0026001F,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43370349,
- .p0_mpdgctrl1 = 0x032D0327,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x3D303639,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x32363934,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_256x32_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0X00480047,
- .p0_mpwldectrl1 = 0X003D003F,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0X423E0241,
- .p0_mpdgctrl1 = 0X022B022C,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0X49454A4A,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0X2E372C32,
-};
-
-static struct mx6_mmdc_calibration mx6dq_256x64_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0X00220021,
- .p0_mpwldectrl1 = 0X00200030,
- .p1_mpwldectrl0 = 0X002D0027,
- .p1_mpwldectrl1 = 0X00150026,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43330342,
- .p0_mpdgctrl1 = 0x0339034A,
- .p1_mpdgctrl0 = 0x032F0325,
- .p1_mpdgctrl1 = 0x032F022E,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0X3A2E3437,
- .p1_mprddlctl = 0X35312F3F,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0X33363B37,
- .p1_mpwrdlctl = 0X40304239,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_256x64_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x0048004A,
- .p0_mpwldectrl1 = 0x003F004A,
- .p1_mpwldectrl0 = 0x001E0028,
- .p1_mpwldectrl1 = 0x002C0043,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x02250219,
- .p0_mpdgctrl1 = 0x01790202,
- .p1_mpdgctrl0 = 0x02080208,
- .p1_mpdgctrl1 = 0x016C0175,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x4A4C4D4C,
- .p1_mprddlctl = 0x494C4A48,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x403F3437,
- .p1_mpwrdlctl = 0x383A3930,
-};
-
-static struct mx6_mmdc_calibration mx6sdl_256x64x2_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x001F003F,
- .p0_mpwldectrl1 = 0x001F001F,
- .p1_mpwldectrl0 = 0x001F004E,
- .p1_mpwldectrl1 = 0x0059001F,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x42220225,
- .p0_mpdgctrl1 = 0x0213021F,
- .p1_mpdgctrl0 = 0x022C0242,
- .p1_mpdgctrl1 = 0x022C0244,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x474A4C4A,
- .p1_mprddlctl = 0x48494C45,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x3F3F3F36,
- .p1_mpwrdlctl = 0x3F36363F,
-};
-
-static struct mx6_mmdc_calibration mx6dq_512x32_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x002A0025,
- .p0_mpwldectrl1 = 0x003A002A,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x43430356,
- .p0_mpdgctrl1 = 0x033C0335,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x4B373F42,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x303E3C36,
-};
-
-static struct mx6_mmdc_calibration mx6dq_512x64_mmdc_calib = {
- /* write leveling calibration determine */
- .p0_mpwldectrl0 = 0x00230020,
- .p0_mpwldectrl1 = 0x002F002A,
- .p1_mpwldectrl0 = 0x001D0027,
- .p1_mpwldectrl1 = 0x00100023,
- /* Read DQS Gating calibration */
- .p0_mpdgctrl0 = 0x03250339,
- .p0_mpdgctrl1 = 0x031C0316,
- .p1_mpdgctrl0 = 0x03210331,
- .p1_mpdgctrl1 = 0x031C025A,
- /* Read Calibration: DQS delay relative to DQ read access */
- .p0_mprddlctl = 0x40373C40,
- .p1_mprddlctl = 0x3A373646,
- /* Write Calibration: DQ/DM delay relative to DQS write access */
- .p0_mpwrdlctl = 0x2E353933,
- .p1_mpwrdlctl = 0x3C2F3F35,
-};
-
-static void spl_dram_init(int width, int size_mb, int board_model)
-{
- struct mx6_ddr3_cfg *mem = NULL;
- struct mx6_mmdc_calibration *calib = NULL;
- struct mx6_ddr_sysinfo sysinfo = {
- /* width of data bus:0=16,1=32,2=64 */
- .dsize = width/32,
- /* config for full 4GB range so that get_mem_size() works */
- .cs_density = 32, /* 32Gb per CS */
- /* single chip select */
- .ncs = 1,
- .cs1_mirror = 0,
- .rtt_wr = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Wr = RZQ/4 */
-#ifdef RTT_NOM_120OHM
- .rtt_nom = 2 /*DDR3_RTT_120_OHM*/, /* RTT_Nom = RZQ/2 */
-#else
- .rtt_nom = 1 /*DDR3_RTT_60_OHM*/, /* RTT_Nom = RZQ/4 */
-#endif
- .walat = 1, /* Write additional latency */
- .ralat = 5, /* Read additional latency */
- .mif3_mode = 3, /* Command prediction working mode */
- .bi_on = 1, /* Bank interleaving enabled */
- .sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
- .rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
- .pd_fast_exit = 1, /* enable precharge power-down fast exit */
- .ddr_type = DDR_TYPE_DDR3,
- .refsel = 1, /* Refresh cycles at 32KHz */
- .refr = 7, /* 8 refresh commands per refresh cycle */
- };
-
- /*
- * MMDC Calibration requires the following data:
- * mx6_mmdc_calibration - board-specific calibration (routing delays)
- * these calibration values depend on board routing, SoC, and DDR
- * mx6_ddr_sysinfo - board-specific memory architecture (width/cs/etc)
- * mx6_ddr_cfg - chip specific timing/layout details
- */
- if (width == 16 && size_mb == 128) {
- mem = &mt41k64m16jt_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- ;
- else
- calib = &mx6sdl_64x16_mmdc_calib;
- debug("1gB density\n");
- } else if (width == 16 && size_mb == 256) {
- /* 1x 2Gb density chip - same calib as 2x 2Gb */
- mem = &mt41k128m16jt_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_128x32_mmdc_calib;
- else
- calib = &mx6sdl_128x32_mmdc_calib;
- debug("2gB density\n");
- } else if (width == 16 && size_mb == 512) {
- mem = &mt41k256m16ha_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_256x16_mmdc_calib;
- else
- calib = &mx6sdl_256x16_mmdc_calib;
- debug("4gB density\n");
- } else if (width == 32 && size_mb == 256) {
- /* Same calib as width==16, size==128 */
- mem = &mt41k64m16jt_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- ;
- else
- calib = &mx6sdl_64x16_mmdc_calib;
- debug("1gB density\n");
- } else if (width == 32 && size_mb == 512) {
- mem = &mt41k128m16jt_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_128x32_mmdc_calib;
- else
- calib = &mx6sdl_128x32_mmdc_calib;
- debug("2gB density\n");
- } else if (width == 32 && size_mb == 1024) {
- mem = &mt41k256m16ha_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_256x32_mmdc_calib;
- else
- calib = &mx6sdl_256x32_mmdc_calib;
- debug("4gB density\n");
- } else if (width == 32 && size_mb == 2048) {
- mem = &mt41k512m16ha_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_512x32_mmdc_calib;
- debug("8gB density\n");
- } else if (width == 64 && size_mb == 512) {
- mem = &mt41k64m16jt_125;
- debug("1gB density\n");
- } else if (width == 64 && size_mb == 1024) {
- mem = &mt41k128m16jt_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_128x64_mmdc_calib;
- else
- calib = &mx6sdl_128x64_mmdc_calib;
- debug("2gB density\n");
- } else if (width == 64 && size_mb == 2048) {
- mem = &mt41k256m16ha_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_256x64_mmdc_calib;
- else
- calib = &mx6sdl_256x64_mmdc_calib;
- debug("4gB density\n");
- } else if (width == 64 && size_mb == 4096) {
- switch(board_model) {
- case GW5903:
- /* 8xMT41K256M16 (4GiB) fly-by mirrored 2-chipsels */
- mem = &mt41k256m16ha_125;
- debug("4gB density\n");
- if (!is_cpu_type(MXC_CPU_MX6Q)) {
- calib = &mx6sdl_256x64x2_mmdc_calib;
- sysinfo.ncs = 2;
- sysinfo.cs_density = 18; /* CS0_END=71 */
- sysinfo.cs1_mirror = 1; /* mirror enabled */
- }
- break;
- default:
- mem = &mt41k512m16ha_125;
- if (is_cpu_type(MXC_CPU_MX6Q))
- calib = &mx6dq_512x64_mmdc_calib;
- debug("8gB density\n");
- break;
- }
- }
-
- if (!(mem && calib)) {
- puts("Error: Invalid Calibration/Board Configuration\n");
- printf("MEM : %s\n", mem ? "OKAY" : "NULL");
- printf("CALIB : %s\n", calib ? "OKAY" : "NULL");
- printf("CPUTYPE: %s\n",
- is_cpu_type(MXC_CPU_MX6Q) ? "IMX6Q" : "IMX6DL");
- printf("SIZE_MB: %d\n", size_mb);
- printf("WIDTH : %d\n", width);
- hang();
- }
-
- if (is_cpu_type(MXC_CPU_MX6Q))
- mx6dq_dram_iocfg(width, &mx6dq_ddr_ioregs,
- &mx6dq_grp_ioregs);
- else
- mx6sdl_dram_iocfg(width, &mx6sdl_ddr_ioregs,
- &mx6sdl_grp_ioregs);
- mx6_dram_cfg(&sysinfo, calib, mem);
-}
-
-static void ccgr_init(void)
-{
- struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
- writel(0x00C03F3F, &ccm->CCGR0);
- writel(0x0030FC03, &ccm->CCGR1);
- writel(0x0FFFC000, &ccm->CCGR2);
- writel(0x3FF00000, &ccm->CCGR3);
- writel(0xFFFFF300, &ccm->CCGR4); /* enable NAND/GPMI/BCH clks */
- writel(0x0F0000C3, &ccm->CCGR5);
- writel(0x000003FF, &ccm->CCGR6);
-}
-
-/*
- * called from C runtime startup code (arch/arm/lib/crt0.S:_main)
- * - we have a stack and a place to store GD, both in SRAM
- * - no variable global data is available
- */
-void board_init_f(ulong dummy)
-{
- struct ventana_board_info ventana_info;
- int board_model;
-
- /* setup clock gating */
- ccgr_init();
-
- /* setup AIPS and disable watchdog */
- arch_cpu_init();
-
- /* setup AXI */
- gpr_init();
-
- /* iomux and setup of i2c */
- setup_iomux_uart();
- setup_ventana_i2c();
-
- /* setup GP timer */
- timer_init();
-
- /* UART clocks enabled and gd valid - init serial console */
- preloader_console_init();
-
- /* read/validate EEPROM info to determine board model and SDRAM cfg */
- board_model = read_eeprom(CONFIG_I2C_GSC, &ventana_info);
-
- /* configure model-specific gpio */
- setup_iomux_gpio(board_model, &ventana_info);
-
- /* provide some some default: 32bit 128MB */
- if (GW_UNKNOWN == board_model)
- hang();
-
- /* configure MMDC for SDRAM width/size and per-model calibration */
- spl_dram_init(8 << ventana_info.sdram_width,
- 16 << ventana_info.sdram_size,
- board_model);
-}
-
-void board_boot_order(u32 *spl_boot_list)
-{
- spl_boot_list[0] = spl_boot_device();
- switch (spl_boot_list[0]) {
- case BOOT_DEVICE_NAND:
- spl_boot_list[1] = BOOT_DEVICE_MMC1;
- spl_boot_list[2] = BOOT_DEVICE_UART;
- break;
- case BOOT_DEVICE_MMC1:
- spl_boot_list[1] = BOOT_DEVICE_UART;
- break;
- }
-}
-
-/* called from board_init_r after gd setup if CONFIG_SPL_BOARD_INIT defined */
-/* its our chance to print info about boot device */
-void spl_board_init(void)
-{
- /* determine boot device from SRC_SBMR1 (BOOT_CFG[4:1]) or SRC_GPR9 */
- u32 boot_device = spl_boot_device();
-
- switch (boot_device) {
- case BOOT_DEVICE_MMC1:
- puts("Booting from MMC\n");
- break;
- case BOOT_DEVICE_NAND:
- puts("Booting from NAND\n");
- break;
- case BOOT_DEVICE_SATA:
- puts("Booting from SATA\n");
- break;
- default:
- puts("Unknown boot device\n");
- }
-
- /* PMIC init */
- setup_pmic();
-}
-
-#ifdef CONFIG_SPL_OS_BOOT
-/* return 1 if we wish to boot to uboot vs os (falcon mode) */
-int spl_start_uboot(void)
-{
- unsigned char ret = 1;
-
- debug("%s\n", __func__);
-#ifdef CONFIG_SPL_ENV_SUPPORT
- env_init();
- env_load();
- debug("boot_os=%s\n", env_get("boot_os"));
- if (env_get_yesno("boot_os") == 1)
- ret = 0;
-#else
- /* use i2c-0:0x50:0x00 for falcon boot mode (0=linux, else uboot) */
- i2c_set_bus_num(0);
- gsc_i2c_read(0x50, 0x0, 1, &ret, 1);
-#endif
- if (!ret)
- gsc_boot_wd_disable();
-
- debug("%s booting %s\n", __func__, ret ? "uboot" : "linux");
- return ret;
-}
-#endif
diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h
deleted file mode 100644
index d2a16f1a008..00000000000
--- a/board/gateworks/gw_ventana/ventana_eeprom.h
+++ /dev/null
@@ -1,133 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Gateworks Corporation
- */
-
-#ifndef _VENTANA_EEPROM_
-#define _VENTANA_EEPROM_
-
-struct ventana_board_info {
- u8 mac0[6]; /* 0x00: MAC1 */
- u8 mac1[6]; /* 0x06: MAC2 */
- u8 res0[12]; /* 0x0C: reserved */
- u32 serial; /* 0x18: Serial Number (read only) */
- u8 res1[4]; /* 0x1C: reserved */
- u8 mfgdate[4]; /* 0x20: MFG date (read only) */
- u8 res2[7]; /* 0x24 */
- /* sdram config */
- u8 sdram_size; /* 0x2B: (16 << n) MB */
- u8 sdram_speed; /* 0x2C: (33.333 * n) MHz */
- u8 sdram_width; /* 0x2D: (8 << n) bit */
- /* cpu config */
- u8 cpu_speed; /* 0x2E: (33.333 * n) MHz */
- u8 cpu_type; /* 0x2F: 7=imx6q, 8=imx6dl */
- u8 model[16]; /* 0x30: model string */
- /* FLASH config */
- u8 nand_flash_size; /* 0x40: (8 << (n-1)) MB */
- u8 spi_flash_size; /* 0x41: (4 << (n-1)) MB */
-
- /* Config1: SoC Peripherals */
- u8 config[8]; /* 0x42: loading options */
-
- u8 res3[4]; /* 0x4A */
-
- u8 chksum[2]; /* 0x4E */
-};
-
-/* config bits */
-enum {
- EECONFIG_ETH0,
- EECONFIG_ETH1,
- EECONFIG_HDMI_OUT,
- EECONFIG_SATA,
- EECONFIG_PCIE,
- EECONFIG_SSI0,
- EECONFIG_SSI1,
- EECONFIG_LCD,
- EECONFIG_LVDS0,
- EECONFIG_LVDS1,
- EECONFIG_USB0,
- EECONFIG_USB1,
- EECONFIG_SD0,
- EECONFIG_SD1,
- EECONFIG_SD2,
- EECONFIG_SD3,
- EECONFIG_UART0,
- EECONFIG_UART1,
- EECONFIG_UART2,
- EECONFIG_UART3,
- EECONFIG_UART4,
- EECONFIG_IPU0,
- EECONFIG_IPU1,
- EECONFIG_FLEXCAN,
- EECONFIG_MIPI_DSI,
- EECONFIG_MIPI_CSI,
- EECONFIG_TZASC0,
- EECONFIG_TZASC1,
- EECONFIG_I2C0,
- EECONFIG_I2C1,
- EECONFIG_I2C2,
- EECONFIG_VPU,
- EECONFIG_CSI0,
- EECONFIG_CSI1,
- EECONFIG_CAAM,
- EECONFIG_MEZZ,
- EECONFIG_RES1,
- EECONFIG_RES2,
- EECONFIG_RES3,
- EECONFIG_RES4,
- EECONFIG_ESPCI0,
- EECONFIG_ESPCI1,
- EECONFIG_ESPCI2,
- EECONFIG_ESPCI3,
- EECONFIG_ESPCI4,
- EECONFIG_ESPCI5,
- EECONFIG_RES5,
- EECONFIG_RES6,
- EECONFIG_GPS,
- EECONFIG_SPIFL0,
- EECONFIG_SPIFL1,
- EECONFIG_GSPBATT,
- EECONFIG_HDMI_IN,
- EECONFIG_VID_OUT,
- EECONFIG_VID_IN,
- EECONFIG_NAND,
- EECONFIG_RES8,
- EECONFIG_RES9,
- EECONFIG_RES10,
- EECONFIG_RES11,
- EECONFIG_RES12,
- EECONFIG_RES13,
- EECONFIG_RES14,
- EECONFIG_RES15,
-};
-
-enum {
- GW54proto, /* original GW5400-A prototype */
- GW51xx,
- GW52xx,
- GW53xx,
- GW54xx,
- GW551x,
- GW552x,
- GW553x,
- GW560x,
- GW5903,
- GW5904,
- GW_UNKNOWN,
- GW_BADCRC,
-};
-
-/* config items */
-struct ventana_eeprom_config {
- const char *name; /* name of item */
- const char *dtalias; /* name of dt node to remove if not set */
- int bit; /* bit within config */
-};
-
-extern struct ventana_eeprom_config econfig[];
-extern struct ventana_board_info ventana_info;
-
-int read_eeprom(int bus, struct ventana_board_info *);
-
-#endif
diff --git a/configs/gwventana_emmc_defconfig b/configs/gwventana_emmc_defconfig
deleted file mode 100644
index eb7614a75a9..00000000000
--- a/configs/gwventana_emmc_defconfig
+++ /dev/null
@@ -1,88 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_TARGET_GW_VENTANA=y
-CONFIG_CMD_EECONFIG=y
-CONFIG_CMD_GSC=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_STACK_R_ADDR=0x18000000
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_DMA_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_OS_BOOT=y
-CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="Ventana > "
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_SPL_NAND_OFS=0x1100000
-CONFIG_CMD_SPL_WRITE_SIZE=0x20000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_DM=y
-CONFIG_DWC_AHSATA=y
-CONFIG_SUPPORT_EMMC_RPMB=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_DEVICE=y
-CONFIG_PHYLIB=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_PCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USB_ETHER=y
-CONFIG_USB_ETH_CDC=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
diff --git a/configs/gwventana_gw5904_defconfig b/configs/gwventana_gw5904_defconfig
deleted file mode 100644
index e2408766e2e..00000000000
--- a/configs/gwventana_gw5904_defconfig
+++ /dev/null
@@ -1,92 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_TARGET_GW_VENTANA=y
-CONFIG_CMD_EECONFIG=y
-CONFIG_CMD_GSC=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_STACK_R_ADDR=0x18000000
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_DMA_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_OS_BOOT=y
-CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="Ventana > "
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_SPL_NAND_OFS=0x1100000
-CONFIG_CMD_SPL_WRITE_SIZE=0x20000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_IS_IN_MMC=y
-CONFIG_DM=y
-CONFIG_DWC_AHSATA=y
-CONFIG_SUPPORT_EMMC_RPMB=y
-CONFIG_FSL_ESDHC=y
-CONFIG_MTD_DEVICE=y
-CONFIG_PHYLIB=y
-CONFIG_MV88E61XX_SWITCH=y
-CONFIG_MV88E61XX_CPU_PORT=5
-CONFIG_MV88E61XX_PHY_PORTS=0xf
-CONFIG_MV88E61XX_FIXED_PORTS=0x0
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_PCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USB_ETHER=y
-CONFIG_USB_ETH_CDC=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
diff --git a/configs/gwventana_nand_defconfig b/configs/gwventana_nand_defconfig
deleted file mode 100644
index 83690f52580..00000000000
--- a/configs/gwventana_nand_defconfig
+++ /dev/null
@@ -1,91 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x17800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_TARGET_GW_VENTANA=y
-CONFIG_CMD_EECONFIG=y
-CONFIG_CMD_GSC=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_STACK_R_ADDR=0x18000000
-CONFIG_CMD_HDMIDETECT=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_FIT=y
-CONFIG_FIT_VERBOSE=y
-CONFIG_OF_BOARD_SETUP=y
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTDELAY=3
-CONFIG_SUPPORT_RAW_INITRD=y
-CONFIG_MISC_INIT_R=y
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_DISPLAY_BOARDINFO_LATE=y
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_BOARD_INIT=y
-CONFIG_SPL_STACK_R=y
-CONFIG_SPL_DMA_SUPPORT=y
-CONFIG_SPL_I2C_SUPPORT=y
-CONFIG_SPL_NAND_SUPPORT=y
-CONFIG_SPL_OS_BOOT=y
-CONFIG_SPL_POWER_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-CONFIG_HUSH_PARSER=y
-CONFIG_SYS_PROMPT="Ventana > "
-CONFIG_CMD_BOOTZ=y
-CONFIG_CMD_SPL_NAND_OFS=0x1100000
-CONFIG_CMD_SPL_WRITE_SIZE=0x20000
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_I2C=y
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND_TRIMFFS=y
-CONFIG_CMD_PCI=y
-CONFIG_CMD_USB=y
-CONFIG_CMD_USB_MASS_STORAGE=y
-CONFIG_CMD_DHCP=y
-CONFIG_CMD_MII=y
-CONFIG_CMD_PING=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_EXT4=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_FS_GENERIC=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=nand:16m(uboot),1m(env),-(rootfs)"
-CONFIG_CMD_UBI=y
-CONFIG_ENV_IS_IN_NAND=y
-CONFIG_DM=y
-CONFIG_DWC_AHSATA=y
-CONFIG_SUPPORT_EMMC_RPMB=y
-CONFIG_FSL_ESDHC=y
-CONFIG_NAND=y
-CONFIG_NAND_MXS=y
-CONFIG_PHYLIB=y
-CONFIG_E1000=y
-CONFIG_MII=y
-CONFIG_PCI=y
-CONFIG_DM_SERIAL=y
-CONFIG_USB=y
-CONFIG_USB_STORAGE=y
-CONFIG_USB_KEYBOARD=y
-CONFIG_SYS_USB_EVENT_POLL_VIA_CONTROL_EP=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_GADGET_MANUFACTURER="Gateworks"
-CONFIG_USB_GADGET_VENDOR_NUM=0x0525
-CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
-CONFIG_CI_UDC=y
-CONFIG_USB_GADGET_DOWNLOAD=y
-CONFIG_USB_ETHER=y
-CONFIG_USB_ETH_CDC=y
-CONFIG_USB_HOST_ETHER=y
-CONFIG_USB_ETHER_ASIX=y
-CONFIG_USB_ETHER_SMSC95XX=y
-CONFIG_VIDEO=y
-# CONFIG_VIDEO_SW_CURSOR is not set
-CONFIG_OF_LIBFDT=y
-CONFIG_FDT_FIXUP_PARTITIONS=y
diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h
deleted file mode 100644
index 6cafdc66859..00000000000
--- a/include/configs/gw_ventana.h
+++ /dev/null
@@ -1,355 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2013 Gateworks Corporation
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/* SPL */
-/* Location in NAND to read U-Boot from */
-#define CONFIG_SYS_NAND_U_BOOT_OFFS (14 * SZ_1M)
-
-/* Falcon Mode */
-#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
-
-/* Falcon Mode - NAND support: args at 17MB kernel at 18MB */
-#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS (18 * SZ_1M)
-
-/* Falcon Mode - MMC support: args at 1MB kernel at 2MB */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x800 /* 1MB */
-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (CONFIG_CMD_SPL_WRITE_SIZE / 512)
-#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1000 /* 2MB */
-
-#include "imx6_spl.h" /* common IMX6 SPL configuration */
-#include "mx6_common.h"
-
-#define CONFIG_MACH_TYPE 4520 /* Gateworks Ventana Platform */
-
-/* Serial ATAG */
-#define CONFIG_SERIAL_TAG
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
-
-/* Init Functions */
-
-/* Driver Model */
-#ifndef CONFIG_SPL_BUILD
-#define CONFIG_DM_GPIO
-#define CONFIG_DM_THERMAL
-#endif
-
-/* Thermal */
-#define CONFIG_IMX_THERMAL
-
-/* Serial */
-#define CONFIG_MXC_UART
-#define CONFIG_MXC_UART_BASE UART2_BASE
-
-#ifdef CONFIG_SPI_FLASH
-
-/* SPI */
-#ifdef CONFIG_CMD_SF
- #define CONFIG_SPI_FLASH_MTD
- #define CONFIG_SPI_FLASH_BAR
- #define CONFIG_SF_DEFAULT_BUS 0
- #define CONFIG_SF_DEFAULT_CS 0
- /* GPIO 3-19 (21248) */
- #define CONFIG_SF_DEFAULT_SPEED 30000000
- #define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
-#endif
-
-#elif defined(CONFIG_SPL_NAND_SUPPORT)
-/* Enable NAND support */
-#ifdef CONFIG_CMD_NAND
- #define CONFIG_SYS_MAX_NAND_DEVICE 1
- #define CONFIG_SYS_NAND_BASE 0x40000000
- #define CONFIG_SYS_NAND_5_ADDR_CYCLE
- #define CONFIG_SYS_NAND_ONFI_DETECTION
-
- /* DMA stuff, needed for GPMI/MXS NAND support */
-#endif
-
-#endif /* CONFIG_SPI_FLASH */
-
-/* I2C Configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
-#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
-#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
-#define CONFIG_SYS_I2C_SPEED 100000
-#define CONFIG_I2C_GSC 0
-#define CONFIG_I2C_EDID
-
-/* MMC Configs */
-#define CONFIG_SYS_FSL_ESDHC_ADDR 0
-
-/* eMMC Configs */
-#define CONFIG_SUPPORT_EMMC_BOOT
-
-/*
- * SATA Configs
- */
-#ifdef CONFIG_CMD_SATA
- #define CONFIG_SYS_SATA_MAX_DEVICE 1
- #define CONFIG_DWC_AHSATA_PORT_ID 0
- #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
- #define CONFIG_LBA48
-#endif
-
-/*
- * PCI express
- */
-#ifdef CONFIG_CMD_PCI
-#define CONFIG_PCI_SCAN_SHOW
-#define CONFIG_PCI_FIXUP_DEV
-#define CONFIG_PCIE_IMX
-#endif
-
-/*
- * PMIC
- */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE100
-#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
-#define CONFIG_POWER_LTC3676
-#define CONFIG_POWER_LTC3676_I2C_ADDR 0x3c
-
-/* Various command support */
-#define CONFIG_CMD_UNZIP /* gzwrite */
-
-/* Ethernet support */
-#define CONFIG_FEC_MXC
-#define IMX_FEC_BASE ENET_BASE_ADDR
-#define CONFIG_FEC_XCV_TYPE RGMII
-#define CONFIG_FEC_MXC_PHYADDR 0
-#define CONFIG_ARP_TIMEOUT 200UL
-
-/* USB Configs */
-#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* For OTG port */
-#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
-#define CONFIG_MXC_USB_FLAGS 0
-#define CONFIG_USBD_HS
-#define CONFIG_NETCONSOLE
-
-/* Framebuffer and LCD */
-#define CONFIG_VIDEO_IPUV3
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_IMX_HDMI
-#define CONFIG_IMX_VIDEO_SKIP
-#define CONFIG_VIDEO_BMP_LOGO
-#define CONFIG_SPLASH_SCREEN_ALIGN
-#define CONFIG_HIDE_LOGO_VERSION /* Custom config to hide U-boot version */
-
-/* Miscellaneous configurable options */
-#define CONFIG_HWCONFIG
-#define CONFIG_PREBOOT
-
-/* Memory configuration */
-#define CONFIG_SYS_MEMTEST_START 0x10000000
-#define CONFIG_SYS_MEMTEST_END 0x10010000
-#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
-
-/* Physical Memory Map */
-#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
- (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
- (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/*
- * MTD Command for mtdparts
- */
-
-/* Persistent Environment Config */
-#if defined(CONFIG_ENV_IS_IN_MMC)
- #define CONFIG_SYS_MMC_ENV_DEV 0
- #define CONFIG_SYS_MMC_ENV_PART 1
- #define CONFIG_ENV_OFFSET (709 * SZ_1K)
- #define CONFIG_ENV_SIZE (128 * SZ_1K)
- #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (128 * SZ_1K))
-#elif defined(CONFIG_ENV_IS_IN_NAND)
- #define CONFIG_ENV_OFFSET (16 * SZ_1M)
- #define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
- #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
- #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + (512 * SZ_1K))
- #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
-#elif defined(CONFIG_ENV_IS_IN_SPI_FLASH)
- #define CONFIG_ENV_OFFSET (512 * SZ_1K)
- #define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
- #define CONFIG_ENV_SIZE (8 * SZ_1K)
- #define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
- #define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
- #define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
- #define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
-#endif
-
-/* Environment */
-#define CONFIG_IPADDR 192.168.1.1
-#define CONFIG_SERVERIP 192.168.1.146
-
-#define CONFIG_EXTRA_ENV_SETTINGS_COMMON \
- "pcidisable=1\0" \
- "splashpos=m,m\0" \
- "usb_pgood_delay=2000\0" \
- "console=ttymxc1\0" \
- "bootdevs=usb mmc sata flash\0" \
- "hwconfig=_UNKNOWN_\0" \
- "video=\0" \
- \
- "mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
- "mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
- "disk=0\0" \
- "part=1\0" \
- \
- "fdt_high=0xffffffff\0" \
- "fdt_addr=0x18000000\0" \
- "initrd_high=0xffffffff\0" \
- "fixfdt=" \
- "fdt addr ${fdt_addr}\0" \
- "bootdir=boot\0" \
- "loadfdt=" \
- "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \
- "echo Loaded DTB from ${bootdir}/${fdt_file}; " \
- "run fixfdt; " \
- "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \
- "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \
- "run fixfdt; " \
- "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \
- "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \
- "run fixfdt; " \
- "fi\0" \
- \
- "fs=ext4\0" \
- "script=6x_bootscript-ventana\0" \
- "loadscript=" \
- "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \
- "source ${loadaddr}; " \
- "fi\0" \
- \
- "uimage=uImage\0" \
- "mmc_root=mmcblk0p1\0" \
- "mmc_boot=" \
- "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \
- "mmc dev ${disk} && mmc rescan && " \
- "setenv dtype mmc; run loadscript; " \
- "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
- "setenv bootargs console=${console},${baudrate} " \
- "root=/dev/${mmc_root} rootfstype=${fs} " \
- "rootwait rw ${video} ${extra}; " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "bootm; " \
- "fi; " \
- "fi\0" \
- \
- "sata_boot=" \
- "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \
- "sata init && " \
- "setenv dtype sata; run loadscript; " \
- "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
- "setenv bootargs console=${console},${baudrate} " \
- "root=/dev/sda1 rootfstype=${fs} " \
- "rootwait rw ${video} ${extra}; " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "bootm; " \
- "fi; " \
- "fi\0" \
- "usb_boot=" \
- "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \
- "usb start && usb dev ${disk} && " \
- "setenv dtype usb; run loadscript; " \
- "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
- "setenv bootargs console=${console},${baudrate} " \
- "root=/dev/sda1 rootfstype=${fs} " \
- "rootwait rw ${video} ${extra}; " \
- "if run loadfdt; then " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "bootm; " \
- "fi; " \
- "fi\0"
-
-#ifdef CONFIG_SPI_FLASH
- #define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_EXTRA_ENV_SETTINGS_COMMON \
- "image_os=ventana/openwrt-imx6-imx6q-gw5400-a-squashfs.bin\0" \
- "image_uboot=ventana/u-boot_spi.imx\0" \
- \
- "spi_koffset=0x90000\0" \
- "spi_klen=0x200000\0" \
- \
- "spi_updateuboot=echo Updating uboot from " \
- "${serverip}:${image_uboot}...; " \
- "tftpboot ${loadaddr} ${image_uboot} && " \
- "sf probe && sf erase 0 80000 && " \
- "sf write ${loadaddr} 400 ${filesize}\0" \
- "spi_update=echo Updating OS from ${serverip}:${image_os} " \
- "to ${spi_koffset} ...; " \
- "tftp ${loadaddr} ${image_os} && " \
- "sf probe && " \
- "sf update ${loadaddr} ${spi_koffset} ${filesize}\0" \
- \
- "flash_boot=" \
- "if sf probe && " \
- "sf read ${loadaddr} ${spi_koffset} ${spi_klen}; then " \
- "setenv bootargs console=${console},${baudrate} " \
- "root=/dev/mtdblock3 " \
- "rootfstype=squashfs,jffs2 " \
- "${video} ${extra}; " \
- "bootm; " \
- "fi\0"
-#else
- #define CONFIG_EXTRA_ENV_SETTINGS \
- CONFIG_EXTRA_ENV_SETTINGS_COMMON \
- \
- "image_rootfs=openwrt-imx6-ventana-rootfs.ubi\0" \
- "nand_update=echo Updating NAND from ${serverip}:${image_rootfs}...; " \
- "tftp ${loadaddr} ${image_rootfs} && " \
- "nand erase.part rootfs && " \
- "nand write ${loadaddr} rootfs ${filesize}\0" \
- \
- "flash_boot=" \
- "setenv fsload 'ubifsload'; " \
- "ubi part rootfs; " \
- "if ubi check boot; then " \
- "ubifsmount ubi0:boot; " \
- "setenv root ubi0:rootfs ubi.mtd=2 " \
- "rootfstype=squashfs,ubifs; " \
- "setenv bootdir; " \
- "elif ubi check rootfs; then " \
- "ubifsmount ubi0:rootfs; " \
- "setenv root ubi0:rootfs ubi.mtd=2 " \
- "rootfstype=ubifs; " \
- "fi; " \
- "setenv dtype nand; run loadscript; " \
- "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \
- "setenv bootargs console=${console},${baudrate} " \
- "root=${root} ${video} ${extra}; " \
- "if run loadfdt; then " \
- "ubifsumount; " \
- "bootm ${loadaddr} - ${fdt_addr}; " \
- "else " \
- "ubifsumount; bootm; " \
- "fi; " \
- "fi\0"
-#endif
-
-#define CONFIG_BOOTCOMMAND \
- "for btype in ${bootdevs}; do " \
- "echo; echo Attempting ${btype} boot...; " \
- "if run ${btype}_boot; then; fi; " \
- "done"
-
-#endif /* __CONFIG_H */
--
2.19.1.1215.g8438c0b245-goog
next prev parent reply other threads:[~2018-11-19 15:53 UTC|newest]
Thread overview: 210+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-11-19 15:52 [U-Boot] [PATCH 00/93] dm: Move towards completing CONFIG_BLK migration Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 01/93] Add a simple script to remove boards Simon Glass
2018-11-19 18:19 ` Adam Ford
2018-11-26 22:24 ` Simon Glass
2018-11-27 0:08 ` Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 02/93] dm: mmc: Use CONFIG_IS_ENABLED to check for BLK Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 03/93] solidrun: Correct typo in MAINTAINERS Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 04/93] arm: Remove s32v234evb board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 05/93] arm: Remove ls1043ardb_sdcard_SECURE_BOOT board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 06/93] arm: Remove ls1046ardb_sdcard_SECURE_BOOT board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 07/93] arm: Remove colibri_imx6_nospl board Simon Glass
2018-11-19 21:32 ` Marek Vasut
2018-11-19 15:52 ` [U-Boot] [PATCH 08/93] arm: Remove guruplug board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 09/93] arm: Remove sniper board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 10/93] arm: Remove omap3_zoom1 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 11/93] arm: Remove sksimx6 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 12/93] arm: Remove tbs2910 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 13/93] arm: Remove theadorable_debug board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 14/93] arm: Remove devkit3250 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 15/93] arm: Remove pcm051_rev3 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 16/93] arm: Remove ds109 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 17/93] arm: Remove pcm058 board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 18/93] arm: Remove am335x_shc_ict board Simon Glass
2018-11-19 15:52 ` [U-Boot] [PATCH 19/93] arm: Remove vining_2000 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 20/93] arm: Remove cm_t43 board Simon Glass
2018-11-19 21:32 ` Marek Vasut
2018-11-19 15:53 ` [U-Boot] [PATCH 21/93] arm: Remove igep00x0 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 22/93] arm: Remove sheevaplug board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 23/93] arm: Remove omap3_overo board Simon Glass
[not found] ` <CAGDS+nkiuiUPGzwtU9kH1jG_hP-Xk7pZcsc7HoZw9PH34xt8jQ@mail.gmail.com>
[not found] ` <CALYyQ17Zn1yhjGA1qWTyP3E4umy+9PjvAdP1DWwqXbVA9rv7Cg@mail.gmail.com>
2018-11-20 13:20 ` Andrew C. Smith
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 24/93] arm: Remove am335x_boneblack board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 25/93] arm: Remove warp7 board Simon Glass
2018-11-19 17:56 ` Fabio Estevam
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` Simon Glass [this message]
2018-11-19 15:53 ` [U-Boot] [PATCH 27/93] arm: Remove cairo board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 28/93] arm: Remove pico-hobbit-imx7d board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 29/93] arm: Remove mccmon6_sd board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 30/93] arm: Remove apalis_imx6_nospl_it board Simon Glass
2018-11-19 21:33 ` Marek Vasut
2018-11-19 15:53 ` [U-Boot] [PATCH 31/93] arm: Remove wandboard board Simon Glass
2018-11-19 21:33 ` Marek Vasut
2018-11-19 15:53 ` [U-Boot] [PATCH 32/93] arm: Remove birdland_bav335a board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 33/93] arm: Remove gurnard board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 34/93] arm: Remove xpress_spl board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 35/93] arm: Remove udoo_neo board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 36/93] arm: Remove nas220 board Simon Glass
2018-11-21 15:26 ` Evgeni Dobrev
2018-11-21 17:08 ` Tom Rini
2018-11-19 15:53 ` [U-Boot] [PATCH 37/93] arm: Remove am335x_pdu001 board Simon Glass
2018-11-29 10:39 ` Felix Brack
2018-11-29 18:42 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 38/93] arm: Remove snapper9260 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 39/93] arm: Remove pfla02 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 40/93] arm: Remove colibri_pxa270 board Simon Glass
2018-11-26 7:57 ` Marcel Ziswiler
2018-11-26 12:57 ` Tom Rini
2018-11-27 0:08 ` Simon Glass
2018-11-27 12:24 ` Marek Vasut
2018-11-19 15:53 ` [U-Boot] [PATCH 41/93] arm: Remove work_92105 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 42/93] arm: Remove omap3_pandora board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 43/93] arm: Remove cl-som-imx7 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 44/93] arm: Remove devkit8000 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 45/93] arm: Remove pengwyn board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 46/93] arm: Remove dreamplug board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 47/93] arm: Remove mx6sabreauto board Simon Glass
2018-11-19 23:56 ` Peng Fan
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 48/93] arm: Remove imx6q_logic board Simon Glass
2018-11-19 18:10 ` Adam Ford
2018-11-27 0:08 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 49/93] arm: Remove zc5202 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 50/93] arm: Remove imx6dl_mamoj board Simon Glass
2018-11-19 17:22 ` Jagan Teki
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 51/93] arm: Remove omap3_logic_somlv board Simon Glass
2018-11-19 18:07 ` Adam Ford
2018-11-27 0:08 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 52/93] arm: Remove cm_t335 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 53/93] arm: Remove liteboard board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 54/93] arm: Remove am43xx_evm_usbhost_boot board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 55/93] arm: Remove chiliboard board Simon Glass
2018-11-21 13:02 ` Marcin Niestrój
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 56/93] arm: Remove am335x_baltos board Simon Glass
2018-11-20 14:56 ` Yegor Yefremov
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 57/93] arm: Remove kp_imx6q_tpc board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 58/93] arm: Remove lsxhl board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 59/93] arm: Remove udoo board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 60/93] arm: Remove marsboard board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 61/93] arm: Remove mx6sabresd board Simon Glass
2018-11-19 23:58 ` Peng Fan
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 62/93] arm: Remove dh_imx6 board Simon Glass
2018-11-20 12:15 ` Ludwig Zenz
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 63/93] arm: Remove vinco board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 64/93] arm: Remove ls1021atwr_sdcard_ifc_SECURE_BOOT board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 65/93] arm: Remove mx6cuboxi board Simon Glass
2018-11-20 7:52 ` Mark Kettenis
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 66/93] arm: Remove ot1200 board Simon Glass
2018-11-22 9:25 ` Christian Gmeiner
2018-11-22 12:52 ` Tom Rini
2018-11-22 13:24 ` Marek Vasut
2018-11-22 13:28 ` Tom Rini
2018-11-22 13:30 ` Marek Vasut
2018-11-22 13:32 ` Tom Rini
2018-11-22 13:40 ` Marek Vasut
2018-11-22 14:44 ` Simon Goldschmidt
2018-11-22 17:01 ` Tom Rini
2018-11-22 20:50 ` Simon Glass
2018-11-25 21:09 ` Simon Goldschmidt
2018-11-26 3:00 ` Simon Glass
2018-11-26 6:05 ` Simon Goldschmidt
2018-12-05 13:21 ` Simon Glass
2018-12-05 13:38 ` Simon Goldschmidt
2018-12-05 13:54 ` Simon Glass
2018-12-05 14:16 ` Simon Goldschmidt
2018-12-05 15:55 ` Simon Glass
2018-12-05 16:11 ` Simon Goldschmidt
2018-11-23 0:33 ` Fabio Estevam
2018-11-19 15:53 ` [U-Boot] [PATCH 67/93] arm: Remove socfpga_stratix10 board Simon Glass
2018-11-21 1:01 ` Ley Foon Tan
2018-11-22 20:50 ` Simon Glass
2018-11-22 23:25 ` Tom Rini
2018-11-23 12:04 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 68/93] arm: Remove am65x_evm_a53 board Simon Glass
2018-11-19 16:58 ` Lokesh Vutla
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 69/93] arm: Remove ap143 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 70/93] arm: Remove ap121 board Simon Glass
2018-11-22 0:47 ` Daniel Schwierzeck
2018-11-22 0:53 ` Tom Rini
2018-11-22 20:50 ` Simon Glass
2018-11-22 23:23 ` Tom Rini
2018-11-24 19:42 ` Simon Glass
2018-11-24 21:22 ` Tom Rini
2018-11-19 15:53 ` [U-Boot] [PATCH 71/93] arm: Remove imgtec_xilfpga board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 72/93] arm: Remove socfpga_de0_nano_soc board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 73/93] arm: Remove clearfog board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 74/93] arm: Remove socfpga_arria10 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 75/93] arm: Remove omap3_beagle board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 76/93] arm: Remove helios4 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 77/93] arm: Remove socfpga_socrates board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 78/93] arm: Remove socfpga_sr1500 board Simon Glass
2018-11-19 15:53 ` [U-Boot] [PATCH 79/93] arm: Remove ls1021aiot_sdcard board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 80/93] arm: Remove socfpga_de10_nano board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 81/93] arm: Remove socfpga_dbm_soc1 board Simon Glass
2018-11-19 21:17 ` Marek Vasut
2018-11-19 15:54 ` [U-Boot] [PATCH 82/93] arm: Remove socfpga_de1_soc board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 83/93] arm: Remove socfpga_sockit board Simon Glass
2018-11-19 20:54 ` Marek Vasut
2018-11-19 15:54 ` [U-Boot] [PATCH 84/93] arm: Remove dns325 board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 85/93] arm: Remove socfpga_is1 board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 86/93] arm: Remove brppt1_mmc board Simon Glass
2018-11-20 11:08 ` Hannes Schmelzer
2018-11-22 20:50 ` Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 87/93] arm: Remove db-mv784mp-gp board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 88/93] arm: Remove socfpga_arria5 board Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 89/93] arm: Remove socfpga_vining_fpga board Simon Glass
2018-11-19 21:16 ` Marek Vasut
2018-11-19 15:54 ` [U-Boot] [PATCH 90/93] arm: Remove dra7xx_evm and dra7xx_hs_evm boards Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 91/93] dm: Enable CONFIG_BLK Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 92/93] dm: Update driver-model migration schedule for CONFIG_BLK Simon Glass
2018-11-19 15:54 ` [U-Boot] [PATCH 93/93] RFC: dm: Force CONFIG_BLK for all boards with DM Simon Glass
2018-11-19 16:08 ` [U-Boot] [PATCH 00/93] dm: Move towards completing CONFIG_BLK migration Otavio Salvador
2018-11-19 18:36 ` Tom Rini
2018-11-19 19:45 ` Adam Ford
2018-11-19 21:32 ` Marek Vasut
2018-11-19 21:54 ` Tom Rini
2018-11-19 21:58 ` Simon Glass
2018-11-20 14:29 ` Ian Campbell
2018-11-20 14:56 ` Tom Rini
2018-11-21 4:43 ` Simon Glass
2018-11-21 13:26 ` Tom Rini
2018-11-19 22:02 ` Adam Ford
2018-11-19 22:06 ` Marek Vasut
2018-11-20 11:00 ` Stefano Babic
2018-11-20 12:39 ` Peter Robinson
2018-11-20 14:55 ` Tom Rini
2018-11-20 16:27 ` Stefano Babic
2018-11-20 17:18 ` Tom Rini
2018-11-19 22:05 ` Marek Vasut
2018-11-20 12:42 ` Soeren Moch
2018-11-20 13:37 ` Tom Rini
2018-11-20 13:40 ` Marek Vasut
2018-11-20 13:42 ` Tom Rini
2018-11-20 13:45 ` Marek Vasut
2018-11-20 13:53 ` Tom Rini
2018-11-20 13:55 ` Marek Vasut
2018-11-21 15:10 ` Tom Rini
2018-11-22 20:50 ` Simon Glass
2018-11-22 23:31 ` Tom Rini
2018-11-23 12:04 ` Simon Glass
2018-11-23 19:38 ` Tom Rini
2018-11-24 19:41 ` Simon Glass
2018-11-26 1:12 ` Tom Rini
2018-11-26 2:59 ` Simon Glass
2018-11-23 0:31 ` Fabio Estevam
2018-11-23 14:35 ` Soeren Moch
2018-11-21 15:13 ` [U-Boot] [PATCH] omap3: beagle: Enable DM_MMC and BLK for u-boot only, not SPL Guillaume GARDET
2018-11-21 17:06 ` Tom Rini
2018-12-17 17:03 ` Guillaume Gardet
2018-12-17 19:34 ` Adam Ford
2018-12-17 20:44 ` Adam Ford
2018-12-18 1:41 ` Tom Rini
2018-11-22 17:45 ` [U-Boot] [PATCH 00/93] dm: Move towards completing CONFIG_BLK migration Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181119155413.158098-27-sjg@chromium.org \
--to=sjg@chromium.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.