[U-Boot] [PATCH 35/93] arm: Remove udoo_neo board

[Simon Glass <sjg@chromium.org>]

This board has not been converted to CONFIG_DM_BLK by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
---

 arch/arm/mach-imx/mx6/Kconfig |   1 -
 board/udoo/neo/Kconfig        |  12 -
 board/udoo/neo/MAINTAINERS    |   7 -
 board/udoo/neo/Makefile       |   4 -
 board/udoo/neo/neo.c          | 595 ----------------------------------
 configs/udoo_neo_defconfig    |  33 --
 include/configs/udoo_neo.h    | 106 ------
 7 files changed, 758 deletions(-)
 delete mode 100644 board/udoo/neo/Kconfig
 delete mode 100644 board/udoo/neo/MAINTAINERS
 delete mode 100644 board/udoo/neo/Makefile
 delete mode 100644 board/udoo/neo/neo.c
 delete mode 100644 configs/udoo_neo_defconfig
 delete mode 100644 include/configs/udoo_neo.h

diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index 3f0d27b76dd..8169bfb18e6 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -558,7 +558,6 @@ source "board/tqc/tqma6/Kconfig"
 source "board/toradex/colibri-imx6ull/Kconfig"
 source "board/k+p/kp_imx6q_tpc/Kconfig"
 source "board/udoo/Kconfig"
-source "board/udoo/neo/Kconfig"
 source "board/warp/Kconfig"
 
 endif
diff --git a/board/udoo/neo/Kconfig b/board/udoo/neo/Kconfig
deleted file mode 100644
index 8f474df2487..00000000000
--- a/board/udoo/neo/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_UDOO_NEO
-
-config SYS_VENDOR
-	default "udoo"
-
-config SYS_BOARD
-	default "neo"
-
-config SYS_CONFIG_NAME
-	default "udoo_neo"
-
-endif
diff --git a/board/udoo/neo/MAINTAINERS b/board/udoo/neo/MAINTAINERS
deleted file mode 100644
index 743fe33d059..00000000000
--- a/board/udoo/neo/MAINTAINERS
+++ /dev/null
@@ -1,7 +0,0 @@
-UDOO NEO BOARD
-M:	Breno Lima <breno.lima@nxp.com>
-M:	Francesco Montefoschi <francesco.montefoschi@udoo.org>
-S:	Maintained
-F:	board/udoo/neo/
-F:	include/configs/udoo_neo.h
-F:	configs/udoo_neo_defconfig
diff --git a/board/udoo/neo/Makefile b/board/udoo/neo/Makefile
deleted file mode 100644
index 831c084ce59..00000000000
--- a/board/udoo/neo/Makefile
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-# (C) Copyright 2015 UDOO Team
-
-obj-y  := neo.o
diff --git a/board/udoo/neo/neo.c b/board/udoo/neo/neo.c
deleted file mode 100644
index 828161360cb..00000000000
--- a/board/udoo/neo/neo.c
+++ /dev/null
@@ -1,595 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * Copyright (C) 2014-2015 Freescale Semiconductor, Inc.
- * Copyright (C) Jasbir Matharu
- * Copyright (C) UDOO Team
- *
- * Author: Breno Lima <breno.lima@nxp.com>
- * Author: Francesco Montefoschi <francesco.monte@gmail.com>
- */
-
-#include <asm/arch/clock.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/iomux.h>
-#include <asm/arch/mx6-pins.h>
-#include <asm/gpio.h>
-#include <asm/mach-imx/iomux-v3.h>
-#include <mmc.h>
-#include <fsl_esdhc.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/io.h>
-#include <asm/mach-imx/mxc_i2c.h>
-#include <asm/arch/sys_proto.h>
-#include <spl.h>
-#include <linux/sizes.h>
-#include <common.h>
-#include <i2c.h>
-#include <miiphy.h>
-#include <netdev.h>
-#include <power/pmic.h>
-#include <power/pfuze3000_pmic.h>
-#include <malloc.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-enum {
-	UDOO_NEO_TYPE_BASIC,
-	UDOO_NEO_TYPE_BASIC_KS,
-	UDOO_NEO_TYPE_FULL,
-	UDOO_NEO_TYPE_EXTENDED,
-};
-
-#define UART_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |		\
-	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
-	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
-	PAD_CTL_PUS_22K_UP  | PAD_CTL_SPEED_LOW |		\
-	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
-
-#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
-	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
-	PAD_CTL_DSE_40ohm | PAD_CTL_HYS |		\
-	PAD_CTL_ODE)
-
-#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |     \
-	PAD_CTL_SPEED_MED   |                                   \
-	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)
-
-#define ENET_CLK_PAD_CTRL  (PAD_CTL_SPEED_MED | \
-	PAD_CTL_DSE_120ohm   | PAD_CTL_SRE_FAST)
-
-#define ENET_RX_PAD_CTRL  (PAD_CTL_PKE | PAD_CTL_PUE |          \
-	PAD_CTL_SPEED_MED   | PAD_CTL_SRE_FAST)
-
-#define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED |	\
-	PAD_CTL_DSE_40ohm)
-
-#define BOARD_DETECT_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
-	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |		\
-	PAD_CTL_DSE_34ohm | PAD_CTL_HYS | PAD_CTL_SRE_FAST)
-#define BOARD_DETECT_PAD_CFG (MUX_PAD_CTRL(BOARD_DETECT_PAD_CTRL) |	\
-	MUX_MODE_SION)
-
-int dram_init(void)
-{
-	gd->ram_size = imx_ddr_size();
-	return 0;
-}
-
-#ifdef CONFIG_SYS_I2C_MXC
-#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
-/* I2C1 for PMIC */
-static struct i2c_pads_info i2c_pad_info1 = {
-	.scl = {
-		.i2c_mode = MX6_PAD_GPIO1_IO00__I2C1_SCL | PC,
-		.gpio_mode = MX6_PAD_GPIO1_IO00__GPIO1_IO_0 | PC,
-		.gp = IMX_GPIO_NR(1, 0),
-	},
-	.sda = {
-		.i2c_mode = MX6_PAD_GPIO1_IO01__I2C1_SDA | PC,
-		.gpio_mode = MX6_PAD_GPIO1_IO01__GPIO1_IO_1 | PC,
-		.gp = IMX_GPIO_NR(1, 1),
-	},
-};
-#endif
-
-#ifdef CONFIG_POWER
-int power_init_board(void)
-{
-	struct pmic *p;
-	int ret;
-	unsigned int reg, rev_id;
-
-	ret = power_pfuze3000_init(PFUZE3000_I2C_BUS);
-	if (ret)
-		return ret;
-
-	p = pmic_get("PFUZE3000");
-	ret = pmic_probe(p);
-	if (ret)
-		return ret;
-
-	pmic_reg_read(p, PFUZE3000_DEVICEID, &reg);
-	pmic_reg_read(p, PFUZE3000_REVID, &rev_id);
-	printf("PMIC:  PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
-
-	/* disable Low Power Mode during standby mode */
-	pmic_reg_read(p, PFUZE3000_LDOGCTL, &reg);
-	reg |= 0x1;
-	ret = pmic_reg_write(p, PFUZE3000_LDOGCTL, reg);
-	if (ret)
-		return ret;
-
-	ret = pmic_reg_write(p, PFUZE3000_SW1AMODE, 0xc);
-	if (ret)
-		return ret;
-
-	ret = pmic_reg_write(p, PFUZE3000_SW1BMODE, 0xc);
-	if (ret)
-		return ret;
-
-	ret = pmic_reg_write(p, PFUZE3000_SW2MODE, 0xc);
-	if (ret)
-		return ret;
-
-	ret = pmic_reg_write(p, PFUZE3000_SW3MODE, 0xc);
-	if (ret)
-		return ret;
-
-	/* set SW1A standby voltage 0.975V */
-	pmic_reg_read(p, PFUZE3000_SW1ASTBY, &reg);
-	reg &= ~0x3f;
-	reg |= PFUZE3000_SW1AB_SETP(9750);
-	ret = pmic_reg_write(p, PFUZE3000_SW1ASTBY, reg);
-	if (ret)
-		return ret;
-
-	/* set SW1B standby voltage 0.975V */
-	pmic_reg_read(p, PFUZE3000_SW1BSTBY, &reg);
-	reg &= ~0x3f;
-	reg |= PFUZE3000_SW1AB_SETP(9750);
-	ret = pmic_reg_write(p, PFUZE3000_SW1BSTBY, reg);
-	if (ret)
-		return ret;
-
-	/* set SW1A/VDD_ARM_IN step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PFUZE3000_SW1ACONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	ret = pmic_reg_write(p, PFUZE3000_SW1ACONF, reg);
-	if (ret)
-		return ret;
-
-	/* set SW1B/VDD_SOC_IN step ramp up time from 16us to 4us/25mV */
-	pmic_reg_read(p, PFUZE3000_SW1BCONF, &reg);
-	reg &= ~0xc0;
-	reg |= 0x40;
-	ret = pmic_reg_write(p, PFUZE3000_SW1BCONF, reg);
-	if (ret)
-		return ret;
-
-	/* set VDD_ARM_IN to 1.350V */
-	pmic_reg_read(p, PFUZE3000_SW1AVOLT, &reg);
-	reg &= ~0x3f;
-	reg |= PFUZE3000_SW1AB_SETP(13500);
-	ret = pmic_reg_write(p, PFUZE3000_SW1AVOLT, reg);
-	if (ret)
-		return ret;
-
-	/* set VDD_SOC_IN to 1.350V */
-	pmic_reg_read(p, PFUZE3000_SW1BVOLT, &reg);
-	reg &= ~0x3f;
-	reg |= PFUZE3000_SW1AB_SETP(13500);
-	ret = pmic_reg_write(p, PFUZE3000_SW1BVOLT, reg);
-	if (ret)
-		return ret;
-
-	/* set DDR_1_5V to 1.350V */
-	pmic_reg_read(p, PFUZE3000_SW3VOLT, &reg);
-	reg &= ~0x0f;
-	reg |= PFUZE3000_SW3_SETP(13500);
-	ret = pmic_reg_write(p, PFUZE3000_SW3VOLT, reg);
-	if (ret)
-		return ret;
-
-	/* set VGEN2_1V5 to 1.5V */
-	pmic_reg_read(p, PFUZE3000_VLDO2CTL, &reg);
-	reg &= ~0x0f;
-	reg |= PFUZE3000_VLDO_SETP(15000);
-	/*  enable  */
-	reg |= 0x10;
-	ret = pmic_reg_write(p, PFUZE3000_VLDO2CTL, reg);
-	if (ret)
-		return ret;
-
-	return 0;
-}
-#endif
-
-static iomux_v3_cfg_t const uart1_pads[] = {
-	MX6_PAD_GPIO1_IO04__UART1_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
-	MX6_PAD_GPIO1_IO05__UART1_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const usdhc2_pads[] = {
-	MX6_PAD_SD2_CLK__USDHC2_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_CMD__USDHC2_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA0__USDHC2_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA1__USDHC2_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA2__USDHC2_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	MX6_PAD_SD2_DATA3__USDHC2_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
-	/* CD pin */
-	MX6_PAD_SD1_DATA0__GPIO6_IO_2 | MUX_PAD_CTRL(NO_PAD_CTRL),
-	/* Power */
-	MX6_PAD_SD1_CMD__GPIO6_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const fec1_pads[] = {
-	MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_RX_CTL__ENET1_RX_EN | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD0__ENET1_RX_DATA_0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_RD1__ENET1_RX_DATA_1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_TX_CTL__ENET1_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_RXC__ENET1_RX_ER | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_RGMII1_TD0__ENET1_TX_DATA_0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_RGMII1_TD1__ENET1_TX_DATA_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-	MX6_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_ENET2_TX_CLK__GPIO2_IO_9 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
-	MX6_PAD_ENET1_CRS__GPIO2_IO_1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const phy_control_pads[] = {
-	/* 25MHz Ethernet PHY Clock */
-	MX6_PAD_ENET2_RX_CLK__ENET2_REF_CLK_25M |
-	MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const board_recognition_pads[] = {
-	/*Connected to R184*/
-	MX6_PAD_NAND_READY_B__GPIO4_IO_13 | BOARD_DETECT_PAD_CFG,
-	/*Connected to R185*/
-	MX6_PAD_NAND_ALE__GPIO4_IO_0 | BOARD_DETECT_PAD_CFG,
-};
-
-static iomux_v3_cfg_t const wdog_b_pad = {
-	MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL),
-};
-
-static iomux_v3_cfg_t const peri_3v3_pads[] = {
-	MX6_PAD_QSPI1A_DATA0__GPIO4_IO_16 | MUX_PAD_CTRL(NO_PAD_CTRL),
-};
-
-static void setup_iomux_uart(void)
-{
-	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
-}
-
-static int setup_fec(int fec_id)
-{
-	struct anatop_regs *anatop = (struct anatop_regs *)ANATOP_BASE_ADDR;
-	int reg;
-
-	imx_iomux_v3_setup_multiple_pads(phy_control_pads,
-					 ARRAY_SIZE(phy_control_pads));
-
-	/* Reset PHY */
-	gpio_direction_output(IMX_GPIO_NR(2, 1) , 0);
-	udelay(10000);
-	gpio_set_value(IMX_GPIO_NR(2, 1), 1);
-	udelay(100);
-
-	reg = readl(&anatop->pll_enet);
-	reg |= BM_ANADIG_PLL_ENET_REF_25M_ENABLE;
-	writel(reg, &anatop->pll_enet);
-
-	return enable_fec_anatop_clock(fec_id, ENET_25MHZ);
-}
-
-int board_eth_init(bd_t *bis)
-{
-	uint32_t base = IMX_FEC_BASE;
-	struct mii_dev *bus = NULL;
-	struct phy_device *phydev = NULL;
-	int ret;
-
-	imx_iomux_v3_setup_multiple_pads(fec1_pads, ARRAY_SIZE(fec1_pads));
-
-	setup_fec(CONFIG_FEC_ENET_DEV);
-
-	bus = fec_get_miibus(base, CONFIG_FEC_ENET_DEV);
-	if (!bus)
-		return -EINVAL;
-
-	phydev = phy_find_by_mask(bus, (0x1 << CONFIG_FEC_MXC_PHYADDR),
-					PHY_INTERFACE_MODE_RMII);
-	if (!phydev) {
-		free(bus);
-		return -EINVAL;
-	}
-
-	ret  = fec_probe(bis, CONFIG_FEC_ENET_DEV, base, bus, phydev);
-	if (ret) {
-		free(bus);
-		free(phydev);
-		return ret;
-	}
-	return 0;
-}
-
-int board_phy_config(struct phy_device *phydev)
-{
-	if (phydev->drv->config)
-		phydev->drv->config(phydev);
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* Address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
-
-	/*
-	 * Because kernel set WDOG_B mux before pad with the commone pinctrl
-	 * framwork now and wdog reset will be triggered once set WDOG_B mux
-	 * with default pad setting, we set pad setting here to workaround this.
-	 * Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
-	 * as GPIO mux firstly here to workaround it.
-	 */
-	imx_iomux_v3_setup_pad(wdog_b_pad);
-
-	/* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */
-	imx_iomux_v3_setup_multiple_pads(peri_3v3_pads,
-					 ARRAY_SIZE(peri_3v3_pads));
-
-	/* Active high for ncp692 */
-	gpio_direction_output(IMX_GPIO_NR(4, 16) , 1);
-
-#ifdef CONFIG_SYS_I2C_MXC
-	setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
-#endif
-
-	return 0;
-}
-
-static int get_board_value(void)
-{
-	int r184, r185;
-
-	imx_iomux_v3_setup_multiple_pads(board_recognition_pads,
-					 ARRAY_SIZE(board_recognition_pads));
-
-	gpio_direction_input(IMX_GPIO_NR(4, 13));
-	gpio_direction_input(IMX_GPIO_NR(4, 0));
-
-	r184 = gpio_get_value(IMX_GPIO_NR(4, 13));
-	r185 = gpio_get_value(IMX_GPIO_NR(4, 0));
-
-	/*
-	 * Machine selection -
-	 * Machine          r184,    r185
-	 * ---------------------------------
-	 * Basic              0        0
-	 * Basic Ks           0        1
-	 * Full               1        0
-	 * Extended           1        1
-	 */
-
-	return (r184 << 1) + r185;
-}
-
-int board_early_init_f(void)
-{
-	setup_iomux_uart();
-
-	return 0;
-}
-
-static struct fsl_esdhc_cfg usdhc_cfg[1] = {
-	{USDHC2_BASE_ADDR, 0, 4},
-};
-
-#define USDHC2_PWR_GPIO IMX_GPIO_NR(6, 1)
-#define USDHC2_CD_GPIO	IMX_GPIO_NR(6, 2)
-
-int board_mmc_getcd(struct mmc *mmc)
-{
-	return !gpio_get_value(USDHC2_CD_GPIO);
-}
-
-int board_mmc_init(bd_t *bis)
-{
-	imx_iomux_v3_setup_multiple_pads(usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
-	usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
-	usdhc_cfg[0].esdhc_base = USDHC2_BASE_ADDR;
-	gpio_direction_input(USDHC2_CD_GPIO);
-	gpio_direction_output(USDHC2_PWR_GPIO, 1);
-
-	gd->arch.sdhc_clk = usdhc_cfg[0].sdhc_clk;
-	return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
-}
-
-static char *board_string(void)
-{
-	switch (get_board_value()) {
-	case UDOO_NEO_TYPE_BASIC:
-		return "BASIC";
-	case UDOO_NEO_TYPE_BASIC_KS:
-		return "BASICKS";
-	case UDOO_NEO_TYPE_FULL:
-		return "FULL";
-	case UDOO_NEO_TYPE_EXTENDED:
-		return "EXTENDED";
-	}
-	return "UNDEFINED";
-}
-
-int checkboard(void)
-{
-	printf("Board: UDOO Neo %s\n", board_string());
-	return 0;
-}
-
-int board_late_init(void)
-{
-#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
-	env_set("board_name", board_string());
-#endif
-
-	return 0;
-}
-
-#ifdef CONFIG_SPL_BUILD
-
-#include <linux/libfdt.h>
-#include <asm/arch/mx6-ddr.h>
-
-static const struct mx6sx_iomux_ddr_regs mx6_ddr_ioregs = {
-	.dram_dqm0 = 0x00000028,
-	.dram_dqm1 = 0x00000028,
-	.dram_dqm2 = 0x00000028,
-	.dram_dqm3 = 0x00000028,
-	.dram_ras = 0x00000020,
-	.dram_cas = 0x00000020,
-	.dram_odt0 = 0x00000020,
-	.dram_odt1 = 0x00000020,
-	.dram_sdba2 = 0x00000000,
-	.dram_sdcke0 = 0x00003000,
-	.dram_sdcke1 = 0x00003000,
-	.dram_sdclk_0 = 0x00000030,
-	.dram_sdqs0 = 0x00000028,
-	.dram_sdqs1 = 0x00000028,
-	.dram_sdqs2 = 0x00000028,
-	.dram_sdqs3 = 0x00000028,
-	.dram_reset = 0x00000020,
-};
-
-static const struct mx6sx_iomux_grp_regs mx6_grp_ioregs = {
-	.grp_addds = 0x00000020,
-	.grp_ddrmode_ctl = 0x00020000,
-	.grp_ddrpke = 0x00000000,
-	.grp_ddrmode = 0x00020000,
-	.grp_b0ds = 0x00000028,
-	.grp_b1ds = 0x00000028,
-	.grp_ctlds = 0x00000020,
-	.grp_ddr_type = 0x000c0000,
-	.grp_b2ds = 0x00000028,
-	.grp_b3ds = 0x00000028,
-};
-
-static const struct mx6_mmdc_calibration neo_mmcd_calib = {
-	.p0_mpwldectrl0 = 0x000E000B,
-	.p0_mpwldectrl1 = 0x000E0010,
-	.p0_mpdgctrl0 = 0x41600158,
-	.p0_mpdgctrl1 = 0x01500140,
-	.p0_mprddlctl = 0x3A383E3E,
-	.p0_mpwrdlctl = 0x3A383C38,
-};
-
-static const struct mx6_mmdc_calibration neo_basic_mmcd_calib = {
-	.p0_mpwldectrl0 = 0x001E0022,
-	.p0_mpwldectrl1 = 0x001C0019,
-	.p0_mpdgctrl0 = 0x41540150,
-	.p0_mpdgctrl1 = 0x01440138,
-	.p0_mprddlctl = 0x403E4644,
-	.p0_mpwrdlctl = 0x3C3A4038,
-};
-
-/* MT41K256M16 */
-static struct mx6_ddr3_cfg neo_mem_ddr = {
-	.mem_speed = 1600,
-	.density = 4,
-	.width = 16,
-	.banks = 8,
-	.rowaddr = 15,
-	.coladdr = 10,
-	.pagesz = 2,
-	.trcd = 1375,
-	.trcmin = 4875,
-	.trasmin = 3500,
-};
-
-/* MT41K128M16 */
-static struct mx6_ddr3_cfg neo_basic_mem_ddr = {
-	.mem_speed = 1600,
-	.density = 2,
-	.width = 16,
-	.banks = 8,
-	.rowaddr = 14,
-	.coladdr = 10,
-	.pagesz = 2,
-	.trcd = 1375,
-	.trcmin = 4875,
-	.trasmin = 3500,
-};
-
-static void ccgr_init(void)
-{
-	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
-
-	writel(0xFFFFFFFF, &ccm->CCGR0);
-	writel(0xFFFFFFFF, &ccm->CCGR1);
-	writel(0xFFFFFFFF, &ccm->CCGR2);
-	writel(0xFFFFFFFF, &ccm->CCGR3);
-	writel(0xFFFFFFFF, &ccm->CCGR4);
-	writel(0xFFFFFFFF, &ccm->CCGR5);
-	writel(0xFFFFFFFF, &ccm->CCGR6);
-	writel(0xFFFFFFFF, &ccm->CCGR7);
-}
-
-static void spl_dram_init(void)
-{
-	int board = get_board_value();
-
-	struct mx6_ddr_sysinfo sysinfo = {
-		.dsize = 1, /* width of data bus: 1 = 32 bits */
-		.cs_density = 24,
-		.ncs = 1,
-		.cs1_mirror = 0,
-		.rtt_wr = 2,
-		.rtt_nom = 2,		/* RTT_Nom = RZQ/2 */
-		.walat = 1,		/* Write additional latency */
-		.ralat = 5,		/* Read additional latency */
-		.mif3_mode = 3,		/* Command prediction working mode */
-		.bi_on = 1,		/* Bank interleaving enabled */
-		.sde_to_rst = 0x10,	/* 14 cycles, 200us (JEDEC default) */
-		.rst_to_cke = 0x23,	/* 33 cycles, 500us (JEDEC default) */
-	};
-
-	mx6sx_dram_iocfg(32, &mx6_ddr_ioregs, &mx6_grp_ioregs);
-	if (board == UDOO_NEO_TYPE_BASIC || board == UDOO_NEO_TYPE_BASIC_KS)
-		mx6_dram_cfg(&sysinfo, &neo_basic_mmcd_calib,
-			     &neo_basic_mem_ddr);
-	else
-		mx6_dram_cfg(&sysinfo, &neo_mmcd_calib, &neo_mem_ddr);
-}
-
-void board_init_f(ulong dummy)
-{
-	ccgr_init();
-
-	/* setup AIPS and disable watchdog */
-	arch_cpu_init();
-
-	board_early_init_f();
-
-	/* setup GP timer */
-	timer_init();
-
-	/* UART clocks enabled and gd valid - init serial console */
-	preloader_console_init();
-
-	/* DDR initialization */
-	spl_dram_init();
-
-	/* Clear the BSS. */
-	memset(__bss_start, 0, __bss_end - __bss_start);
-
-	/* load/boot image from boot device */
-	board_init_r(NULL, 0);
-}
-
-#endif
diff --git a/configs/udoo_neo_defconfig b/configs/udoo_neo_defconfig
deleted file mode 100644
index de0e03726b8..00000000000
--- a/configs/udoo_neo_defconfig
+++ /dev/null
@@ -1,33 +0,0 @@
-CONFIG_ARM=y
-CONFIG_ARCH_MX6=y
-CONFIG_SYS_TEXT_BASE=0x87800000
-CONFIG_SPL_GPIO_SUPPORT=y
-CONFIG_SPL_LIBCOMMON_SUPPORT=y
-CONFIG_SPL_LIBGENERIC_SUPPORT=y
-CONFIG_TARGET_UDOO_NEO=y
-CONFIG_SPL_MMC_SUPPORT=y
-CONFIG_SPL_SERIAL_SUPPORT=y
-CONFIG_SPL=y
-CONFIG_SPL_LIBDISK_SUPPORT=y
-# CONFIG_CMD_BMODE is not set
-CONFIG_DISTRO_DEFAULTS=y
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
-CONFIG_BOOTCOMMAND="run findfdt; run distro_bootcmd"
-CONFIG_BOARD_EARLY_INIT_F=y
-CONFIG_SPL_ENV_SUPPORT=y
-CONFIG_SPL_EXT_SUPPORT=y
-CONFIG_SPL_WATCHDOG_SUPPORT=y
-# CONFIG_CMD_FLASH is not set
-CONFIG_CMD_GPIO=y
-CONFIG_CMD_MMC=y
-# CONFIG_CMD_SETEXPR is not set
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_TIME=y
-CONFIG_CMD_EXT4_WRITE=y
-CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
-CONFIG_FSL_ESDHC=y
-CONFIG_PHYLIB=y
-CONFIG_PHY_MICREL=y
-CONFIG_MII=y
-CONFIG_OF_LIBFDT=y
diff --git a/include/configs/udoo_neo.h b/include/configs/udoo_neo.h
deleted file mode 100644
index 6ba4270b72d..00000000000
--- a/include/configs/udoo_neo.h
+++ /dev/null
@@ -1,106 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright 2014-2015 Freescale Semiconductor, Inc.
- * Copyright Jasbir Matharu
- * Copyright 2015 UDOO Team
- *
- * Configuration settings for the UDOO NEO board.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include "mx6_common.h"
-
-#include "imx6_spl.h"
-
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN		(3 * SZ_1M)
-#define CONFIG_MXC_UART
-
-/* MMC Configuration */
-#define CONFIG_SYS_FSL_ESDHC_ADDR	USDHC2_BASE_ADDR
-
-/* Command definition */
-#define CONFIG_MXC_UART_BASE		UART1_BASE
-#define CONFIG_SYS_MMC_ENV_DEV		0  /*USDHC2*/
-
-/* Linux only */
-#define CONFIG_EXTRA_ENV_SETTINGS \
-	"console=ttymxc0,115200\0" \
-	"fdt_high=0xffffffff\0" \
-	"initrd_high=0xffffffff\0" \
-	"fdtfile=undefined\0" \
-	"fdt_addr=0x83000000\0" \
-	"fdt_addr_r=0x83000000\0" \
-	"ip_dyn=yes\0" \
-	"mmcdev=0\0" \
-	"mmcrootfstype=ext4\0" \
-	"findfdt="\
-		"if test $board_name = BASIC; then " \
-			"setenv fdtfile imx6sx-udoo-neo-basic.dtb; fi; " \
-		"if test $board_name = BASICKS; then " \
-			"setenv fdtfile imx6sx-udoo-neo-basic.dtb; fi; " \
-		"if test $board_name = FULL; then " \
-			"setenv fdtfile imx6sx-udoo-neo-full.dtb; fi; " \
-		"if test $board_name = EXTENDED; then " \
-			"setenv fdtfile imx6sx-udoo-neo-extended.dtb; fi; " \
-		"if test $fdtfile = UNDEFINED; then " \
-			"echo WARNING: Could not determine dtb to use; fi\0" \
-	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
-	"pxefile_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
-	"ramdisk_addr_r=0x84000000\0" \
-	"scriptaddr=" __stringify(CONFIG_LOADADDR) "\0" \
-	BOOTENV
-
-#define BOOT_TARGET_DEVICES(func) \
-	func(MMC, mmc, 0) \
-	func(DHCP, dhcp, na)
-
-#include <config_distro_bootcmd.h>
-
-/* Miscellaneous configurable options */
-#define CONFIG_SYS_MEMTEST_START	0x80000000
-#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x10000)
-
-/* Physical Memory Map */
-#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
-#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
-#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
-#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
-
-#define CONFIG_SYS_INIT_SP_OFFSET \
-	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_ADDR \
-	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
-
-/* Environment organization */
-#define CONFIG_ENV_OFFSET		(8 * SZ_64K)
-#define CONFIG_ENV_SIZE			SZ_8K
-
-#define CONFIG_IMX_THERMAL
-
-/* I2C configs */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_MXC
-#define CONFIG_SYS_I2C_MXC_I2C1
-#define CONFIG_SYS_I2C_SPEED		100000
-
-/* PMIC */
-#define CONFIG_POWER
-#define CONFIG_POWER_I2C
-#define CONFIG_POWER_PFUZE3000
-#define CONFIG_POWER_PFUZE3000_I2C_ADDR	0x08
-#define PFUZE3000_I2C_BUS	0
-
-/* Network */
-#define CONFIG_FEC_MXC
-
-#define CONFIG_FEC_ENET_DEV 0
-#define IMX_FEC_BASE			ENET_BASE_ADDR
-#define CONFIG_FEC_MXC_PHYADDR          0x0
-
-#define CONFIG_FEC_XCV_TYPE             RMII
-#define CONFIG_ETHPRIME                 "FEC0"
-
-#endif				/* __CONFIG_H */
-- 
2.19.1.1215.g8438c0b245-goog