* [PATCH v2 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Philipp Zabel, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
Hi,
this is the quite expanded second version of the support series for the
Allwinner H616 SoC.
Besides many fixes for the bugs discovered by the diligent reviewers
(many thanks for that!) this version adds some patches to support some
slightly changed devices, like the second EMAC and the AXP not having
an interrupt.
Also I added quite some DT binding doc patches.
USB still does not work, but I include the patches anyway, hoping that
someone can help spotting the issue.
For a more detailed changelog see below.
Thanks!
Andre
==================
This series gathers patches to support the Allwinner H616 SoC. This is
a rather uninspired SoC (Quad-A53 with the usual peripherals), but
allows for some cheap development boards and TV boxes, and supports
up to 4GB of DRAM.
Various DT binding patches are sprinkled throughout the series, to add
the new compatible names right before they are used.
Patch 1/21 is the usual drive-by fix, discovered while staring at
the H6 clock code.
Patch 3 and 4 add pinctrl support, with the "-R" controller now being
crippled down to two I2C pins only. If we grow tired of repeating this
exercise for every new SoC variant, I am happy to revive my more
versatile sunxi pinctrl driver effort from a few years back [1].
Patch 6 and 7 add clock support. For the -R clock this is shared with
the H6 code, as the clocks are identical, with the H616 just having
fewer of them. The main clocks are different enough to warrant a separate
file.
Patch 08/21 is pulling a patch from Yangtao's A100 series, since we need
the same fix for MMC support. This will probably be merged separately,
I just include this here to provide a bootable solution.
Patch 10 teaches the AXP MFD driver to get along without having an
interrupt, as the H616 apparently does not have an NMI controller anymore.
Patch 12 and 13 add some tweaks to the syscon and EMAC driver, to deal
with the second EMAC clock used for the second Ethernet controller.
Patches 14 and 15 *try* to add USB support. The same approach works with
the very similar U-Boot PHY driver, but for some reason still fail in
Linux. Maybe someone spots the issue and can help fixing it?
The remaining patches add DT bindings, which just add the new compatible
string along with an existing name as a fallback string.
Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
the OrangePi Zero2 board[2] in the last patch.
We have U-Boot and Trusted-Firmware support in a working state, booting
via FEL and even TFTPing kernels work already [3][4].
Many thanks to Jernej for his tremendous help on this, also for the
awesome input and help from the #linux-sunxi Freenode channel.
The whole series can also be found here:
https://github.com/apritzel/linux/commits/h616-v2
Happy reviewing!
Cheers,
Andre
[1] https://patchwork.ozlabs.org/project/linux-gpio/cover/20171113012523.2328-1-andre.przywara@arm.com/
[2] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
[3] https://github.com/jernejsk/u-boot/commits/h616-v1
[4] https://github.com/apritzel/arm-trusted-firmware/commits/h616-WIP
Changelog v1 .. v2:
- pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
- use differing h_i2s0 pin output names
- r-ccu: fix number of used clocks
- ccu: remove PLL-PERIPHy(4X)
- ccu: fix gpu1 divider range
- ccu: fix usb-phy3 parent
- ccu: add missing TV clocks
- ccu: rework to CLK_OF_DECLARE style
- ccu: enable output bit for PLL clocks
- ccu: renumber clocks
- .dtsi: drop sun50i-a64-system-control fallback
- .dtsi: drop unknown SRAM regions
- .dtsi: add more (undocumented) GPIO interrupts
- .dtsi: fix I2C3 pin names
- .dtsi: use a100-emmc fallback for MMC2
- .dtsi: add second EMAC controller
- .dtsi: use H3 MUSB controller fallback
- .dtsi: fix frame size for USB PHY PMU registers
- .dtsi: add USB0 PHY references
- .dtsi: fix IR controller clock source
- .dts: fix LED naming and swap pins
- .dts: use 5V supply parent for USB supply
- .dts: drop dummy IRQ for AXP
- .dts: enable 3V3 header pin power rail
- .dts: add SPI flash node
- .dts: make USB-C port peripheral only
- add IRQ-less AXP support
- add two patches to support more than one EMAC clock
- add patch to rework and extend USB PHY support
- add DT binding documentation patches
Andre Przywara (18):
clk: sunxi-ng: h6: Fix clock divider range on some clocks
dt-bindings: pinctrl: Add Allwinner H616 compatible strings
pinctrl: sunxi: Add support for the Allwinner H616 pin controller
pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
clk: sunxi-ng: Add support for the Allwinner H616 CCU
mfd: axp20x: Allow AXP chips without interrupt lines
dt-bindings: sram: sunxi-sram: Add H616 compatible string
soc: sunxi: sram: Add support for more than one EMAC clock
net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
phy: sun4i-usb: Rework "pmu_unk1" handling
phy: sun4i-usb: Add support for the H616 USB PHY
dt-bindings: watchdog: sun4i: Add H616 compatible string
dt-bindings: allwinner: Add H616 compatible strings
arm64: dts: allwinner: Add Allwinner H616 .dtsi file
dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
arm64: dts: allwinner: Add OrangePi Zero 2 .dts
Yangtao Li (3):
dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
mmc: sunxi: add support for A100 mmc controller
dt-bindings: watchdog: sun4i: Add A100 compatible
.../devicetree/bindings/arm/sunxi.yaml | 5 +
.../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
.../media/allwinner,sun4i-a10-ir.yaml | 16 +-
.../bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 +
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 2 +
.../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
.../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
.../allwinner,sun4i-a10-system-control.yaml | 1 +
.../watchdog/allwinner,sun4i-a10-wdt.yaml | 9 +-
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++
.../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++
drivers/clk/sunxi-ng/Kconfig | 7 +-
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +-
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 +-
drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150 +++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
drivers/mfd/axp20x.c | 17 +-
drivers/mmc/host/sunxi-mmc.c | 28 +-
.../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
drivers/phy/allwinner/phy-sun4i-usb.c | 39 +-
drivers/pinctrl/sunxi/Kconfig | 10 +
drivers/pinctrl/sunxi/Makefile | 2 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++
drivers/soc/sunxi/sunxi_sram.c | 31 +-
include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
31 files changed, 3151 insertions(+), 71 deletions(-)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 01/21] clk: sunxi-ng: h6: Fix clock divider range on some clocks
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, linux-clk
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
index f2497d0a4683..d0565d378ea2 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
@@ -237,7 +237,7 @@ static const char * const psi_ahb1_ahb2_parents[] = { "osc24M", "osc32k",
static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
psi_ahb1_ahb2_parents,
0x510,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
@@ -246,19 +246,19 @@ static const char * const ahb3_apb1_apb2_parents[] = { "osc24M", "osc32k",
"psi-ahb1-ahb2",
"pll-periph0" };
static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 01/21] clk: sunxi-ng: h6: Fix clock divider range on some clocks
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel, linux-clk,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
index f2497d0a4683..d0565d378ea2 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6.c
@@ -237,7 +237,7 @@ static const char * const psi_ahb1_ahb2_parents[] = { "osc24M", "osc32k",
static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
psi_ahb1_ahb2_parents,
0x510,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
@@ -246,19 +246,19 @@ static const char * const ahb3_apb1_apb2_parents[] = { "osc24M", "osc32k",
"psi-ahb1-ahb2",
"pll-periph0" };
static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
- 0, 5, /* M */
+ 0, 2, /* M */
8, 2, /* P */
24, 2, /* mux */
0);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, devicetree,
linux-gpio
A new SoC, a new compatible string.
Also we were too miserly with just allowing seven interrupt banks.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 5240487dfe50..292b05d9ed08 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -53,6 +53,8 @@ properties:
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
+ - allwinner,sun50i-h616-pinctrl
+ - allwinner,sun50i-h616-r-pinctrl
- allwinner,suniv-f1c100s-pinctrl
- nextthing,gr8-pinctrl
@@ -61,7 +63,7 @@ properties:
interrupts:
minItems: 1
- maxItems: 7
+ maxItems: 8
description:
One interrupt per external interrupt bank supported on the
controller, sorted by bank number ascending order.
@@ -91,7 +93,7 @@ properties:
bank found in the controller
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
- maxItems: 5
+ maxItems: 8
patternProperties:
# It's pretty scary, but the basic idea is that:
@@ -145,6 +147,18 @@ allOf:
# boards are defining it at the moment so it would generate a lot of
# warnings.
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun50i-h616-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 8
+ maxItems: 8
+
- if:
properties:
compatible:
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-gpio, linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
A new SoC, a new compatible string.
Also we were too miserly with just allowing seven interrupt banks.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18 ++++++++++++++++--
1 file changed, 16 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
index 5240487dfe50..292b05d9ed08 100644
--- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
@@ -53,6 +53,8 @@ properties:
- allwinner,sun50i-h5-pinctrl
- allwinner,sun50i-h6-pinctrl
- allwinner,sun50i-h6-r-pinctrl
+ - allwinner,sun50i-h616-pinctrl
+ - allwinner,sun50i-h616-r-pinctrl
- allwinner,suniv-f1c100s-pinctrl
- nextthing,gr8-pinctrl
@@ -61,7 +63,7 @@ properties:
interrupts:
minItems: 1
- maxItems: 7
+ maxItems: 8
description:
One interrupt per external interrupt bank supported on the
controller, sorted by bank number ascending order.
@@ -91,7 +93,7 @@ properties:
bank found in the controller
$ref: /schemas/types.yaml#/definitions/uint32-array
minItems: 1
- maxItems: 5
+ maxItems: 8
patternProperties:
# It's pretty scary, but the basic idea is that:
@@ -145,6 +147,18 @@ allOf:
# boards are defining it at the moment so it would generate a lot of
# warnings.
+ - if:
+ properties:
+ compatible:
+ enum:
+ - allwinner,sun50i-h616-pinctrl
+
+ then:
+ properties:
+ interrupts:
+ minItems: 8
+ maxItems: 8
+
- if:
properties:
compatible:
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 9:37 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:37 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree, linux-gpio
[-- Attachment #1: Type: text/plain, Size: 2173 bytes --]
On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> A new SoC, a new compatible string.
> Also we were too miserly with just allowing seven interrupt banks.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18 ++++++++++++++++--
> 1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 5240487dfe50..292b05d9ed08 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -53,6 +53,8 @@ properties:
> - allwinner,sun50i-h5-pinctrl
> - allwinner,sun50i-h6-pinctrl
> - allwinner,sun50i-h6-r-pinctrl
> + - allwinner,sun50i-h616-pinctrl
> + - allwinner,sun50i-h616-r-pinctrl
> - allwinner,suniv-f1c100s-pinctrl
> - nextthing,gr8-pinctrl
>
> @@ -61,7 +63,7 @@ properties:
>
> interrupts:
> minItems: 1
> - maxItems: 7
> + maxItems: 8
> description:
> One interrupt per external interrupt bank supported on the
> controller, sorted by bank number ascending order.
> @@ -91,7 +93,7 @@ properties:
> bank found in the controller
> $ref: /schemas/types.yaml#/definitions/uint32-array
> minItems: 1
> - maxItems: 5
> + maxItems: 8
>
> patternProperties:
> # It's pretty scary, but the basic idea is that:
> @@ -145,6 +147,18 @@ allOf:
> # boards are defining it at the moment so it would generate a lot of
> # warnings.
>
> + - if:
> + properties:
> + compatible:
> + enum:
> + - allwinner,sun50i-h616-pinctrl
> +
> + then:
> + properties:
> + interrupts:
> + minItems: 8
> + maxItems: 8
> +
You don't need to have both if they are equals, and in this particular
case we already check that the maximum is 8 so there's no need to repeat
that check here.
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
@ 2020-12-14 9:37 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:37 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, linux-gpio,
Chen-Yu Tsai, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2173 bytes --]
On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> A new SoC, a new compatible string.
> Also we were too miserly with just allowing seven interrupt banks.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18 ++++++++++++++++--
> 1 file changed, 16 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> index 5240487dfe50..292b05d9ed08 100644
> --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> @@ -53,6 +53,8 @@ properties:
> - allwinner,sun50i-h5-pinctrl
> - allwinner,sun50i-h6-pinctrl
> - allwinner,sun50i-h6-r-pinctrl
> + - allwinner,sun50i-h616-pinctrl
> + - allwinner,sun50i-h616-r-pinctrl
> - allwinner,suniv-f1c100s-pinctrl
> - nextthing,gr8-pinctrl
>
> @@ -61,7 +63,7 @@ properties:
>
> interrupts:
> minItems: 1
> - maxItems: 7
> + maxItems: 8
> description:
> One interrupt per external interrupt bank supported on the
> controller, sorted by bank number ascending order.
> @@ -91,7 +93,7 @@ properties:
> bank found in the controller
> $ref: /schemas/types.yaml#/definitions/uint32-array
> minItems: 1
> - maxItems: 5
> + maxItems: 8
>
> patternProperties:
> # It's pretty scary, but the basic idea is that:
> @@ -145,6 +147,18 @@ allOf:
> # boards are defining it at the moment so it would generate a lot of
> # warnings.
>
> + - if:
> + properties:
> + compatible:
> + enum:
> + - allwinner,sun50i-h616-pinctrl
> +
> + then:
> + properties:
> + interrupts:
> + minItems: 8
> + maxItems: 8
> +
You don't need to have both if they are equals, and in this particular
case we already check that the maximum is 8 so there's no need to repeat
that check here.
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
2020-12-14 9:37 ` Maxime Ripard
@ 2021-01-14 0:45 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2021-01-14 0:45 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree, linux-gpio
On Mon, 14 Dec 2020 10:37:28 +0100
Maxime Ripard <maxime@cerno.tech> wrote:
> On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> > A new SoC, a new compatible string.
> > Also we were too miserly with just allowing seven interrupt banks.
> >
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > ---
> > .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18
> > ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > index 5240487dfe50..292b05d9ed08 100644 ---
> > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > +++
> > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > @@ -53,6 +53,8 @@ properties:
> > - allwinner,sun50i-h5-pinctrl
> > - allwinner,sun50i-h6-pinctrl
> > - allwinner,sun50i-h6-r-pinctrl
> > + - allwinner,sun50i-h616-pinctrl
> > + - allwinner,sun50i-h616-r-pinctrl
> > - allwinner,suniv-f1c100s-pinctrl
> > - nextthing,gr8-pinctrl
> >
> > @@ -61,7 +63,7 @@ properties:
> >
> > interrupts:
> > minItems: 1
> > - maxItems: 7
> > + maxItems: 8
> > description:
> > One interrupt per external interrupt bank supported on the
> > controller, sorted by bank number ascending order.
> > @@ -91,7 +93,7 @@ properties:
> > bank found in the controller
> > $ref: /schemas/types.yaml#/definitions/uint32-array
> > minItems: 1
> > - maxItems: 5
> > + maxItems: 8
> >
> > patternProperties:
> > # It's pretty scary, but the basic idea is that:
> > @@ -145,6 +147,18 @@ allOf:
> > # boards are defining it at the moment so it would generate a
> > lot of # warnings.
> >
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - allwinner,sun50i-h616-pinctrl
> > +
> > + then:
> > + properties:
> > + interrupts:
> > + minItems: 8
> > + maxItems: 8
> > +
>
> You don't need to have both if they are equals, and in this particular
Mmh, but all the other compatibles have both equal, so what would be
the recommended way to describe this? Just minItems? I don't find a
good explanation at the moment how to handle an explicit number, other
than by enumerating the items explicitly.
> case we already check that the maximum is 8 so there's no need to
> repeat that check here.
Are you referring to the overall "maxItems: 8" above, in the 2nd hunk?
While this will become redundant, this is apparently prone to changes
(as only "7" would be redundant at the moment), so I would rather not
rely on a global limit.
Cheers,
Andre.
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
@ 2021-01-14 0:45 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2021-01-14 0:45 UTC (permalink / raw)
To: Maxime Ripard
Cc: Jernej Skrabec, devicetree, Yangtao Li, Linus Walleij,
linux-sunxi, linux-kernel, linux-gpio, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
On Mon, 14 Dec 2020 10:37:28 +0100
Maxime Ripard <maxime@cerno.tech> wrote:
> On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> > A new SoC, a new compatible string.
> > Also we were too miserly with just allowing seven interrupt banks.
> >
> > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > ---
> > .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18
> > ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-)
> >
> > diff --git
> > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > index 5240487dfe50..292b05d9ed08 100644 ---
> > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > +++
> > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > @@ -53,6 +53,8 @@ properties:
> > - allwinner,sun50i-h5-pinctrl
> > - allwinner,sun50i-h6-pinctrl
> > - allwinner,sun50i-h6-r-pinctrl
> > + - allwinner,sun50i-h616-pinctrl
> > + - allwinner,sun50i-h616-r-pinctrl
> > - allwinner,suniv-f1c100s-pinctrl
> > - nextthing,gr8-pinctrl
> >
> > @@ -61,7 +63,7 @@ properties:
> >
> > interrupts:
> > minItems: 1
> > - maxItems: 7
> > + maxItems: 8
> > description:
> > One interrupt per external interrupt bank supported on the
> > controller, sorted by bank number ascending order.
> > @@ -91,7 +93,7 @@ properties:
> > bank found in the controller
> > $ref: /schemas/types.yaml#/definitions/uint32-array
> > minItems: 1
> > - maxItems: 5
> > + maxItems: 8
> >
> > patternProperties:
> > # It's pretty scary, but the basic idea is that:
> > @@ -145,6 +147,18 @@ allOf:
> > # boards are defining it at the moment so it would generate a
> > lot of # warnings.
> >
> > + - if:
> > + properties:
> > + compatible:
> > + enum:
> > + - allwinner,sun50i-h616-pinctrl
> > +
> > + then:
> > + properties:
> > + interrupts:
> > + minItems: 8
> > + maxItems: 8
> > +
>
> You don't need to have both if they are equals, and in this particular
Mmh, but all the other compatibles have both equal, so what would be
the recommended way to describe this? Just minItems? I don't find a
good explanation at the moment how to handle an explicit number, other
than by enumerating the items explicitly.
> case we already check that the maximum is 8 so there's no need to
> repeat that check here.
Are you referring to the overall "maxItems: 8" above, in the 2nd hunk?
While this will become redundant, this is apparently prone to changes
(as only "7" would be redundant at the moment), so I would rather not
rely on a global limit.
Cheers,
Andre.
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
2021-01-14 0:45 ` Andre Przywara
@ 2021-01-14 11:57 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2021-01-14 11:57 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree, linux-gpio
[-- Attachment #1: Type: text/plain, Size: 3827 bytes --]
On Thu, Jan 14, 2021 at 12:45:12AM +0000, Andre Przywara wrote:
> On Mon, 14 Dec 2020 10:37:28 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
>
> > On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> > > A new SoC, a new compatible string.
> > > Also we were too miserly with just allowing seven interrupt banks.
> > >
> > > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > > ---
> > > .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18
> > > ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-)
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > index 5240487dfe50..292b05d9ed08 100644 ---
> > > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > +++
> > > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > @@ -53,6 +53,8 @@ properties:
> > > - allwinner,sun50i-h5-pinctrl
> > > - allwinner,sun50i-h6-pinctrl
> > > - allwinner,sun50i-h6-r-pinctrl
> > > + - allwinner,sun50i-h616-pinctrl
> > > + - allwinner,sun50i-h616-r-pinctrl
> > > - allwinner,suniv-f1c100s-pinctrl
> > > - nextthing,gr8-pinctrl
> > >
> > > @@ -61,7 +63,7 @@ properties:
> > >
> > > interrupts:
> > > minItems: 1
> > > - maxItems: 7
> > > + maxItems: 8
> > > description:
> > > One interrupt per external interrupt bank supported on the
> > > controller, sorted by bank number ascending order.
> > > @@ -91,7 +93,7 @@ properties:
> > > bank found in the controller
> > > $ref: /schemas/types.yaml#/definitions/uint32-array
> > > minItems: 1
> > > - maxItems: 5
> > > + maxItems: 8
> > >
> > > patternProperties:
> > > # It's pretty scary, but the basic idea is that:
> > > @@ -145,6 +147,18 @@ allOf:
> > > # boards are defining it at the moment so it would generate a
> > > lot of # warnings.
> > >
> > > + - if:
> > > + properties:
> > > + compatible:
> > > + enum:
> > > + - allwinner,sun50i-h616-pinctrl
> > > +
> > > + then:
> > > + properties:
> > > + interrupts:
> > > + minItems: 8
> > > + maxItems: 8
> > > +
> >
> > You don't need to have both if they are equals, and in this particular
>
> Mmh, but all the other compatibles have both equal, so what would be
> the recommended way to describe this? Just minItems? I don't find a
> good explanation at the moment how to handle an explicit number, other
> than by enumerating the items explicitly.
This is where the magic happens:
https://github.com/devicetree-org/dt-schema/blob/master/dtschema/lib.py#L258
So, if there's an items property, it will expand minItems and maxItems
according to the length of the list. Else, it will see if there's either
minItems and maxItems and set the other one if it's missing.
In this case, minItems and maxItems are equals, so you could just fill
one of them
> > case we already check that the maximum is 8 so there's no need to
> > repeat that check here.
>
> Are you referring to the overall "maxItems: 8" above, in the 2nd hunk?
> While this will become redundant, this is apparently prone to changes
> (as only "7" would be redundant at the moment), so I would rather not
> rely on a global limit.
Yeah, my point was that since the upper schema checks for the interrupts
array length to be between 1 and 8, there's no need to specify a max of
8, the upper schema has it covered.
You're right that the max is increased regularly, however we can still
rely on the above logic to fill maxItems to 8 anyway
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 02/21] dt-bindings: pinctrl: Add Allwinner H616 compatible strings
@ 2021-01-14 11:57 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2021-01-14 11:57 UTC (permalink / raw)
To: Andre Przywara
Cc: Jernej Skrabec, devicetree, Yangtao Li, Linus Walleij,
linux-sunxi, linux-kernel, linux-gpio, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 3827 bytes --]
On Thu, Jan 14, 2021 at 12:45:12AM +0000, Andre Przywara wrote:
> On Mon, 14 Dec 2020 10:37:28 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
>
> > On Fri, Dec 11, 2020 at 01:19:15AM +0000, Andre Przywara wrote:
> > > A new SoC, a new compatible string.
> > > Also we were too miserly with just allowing seven interrupt banks.
> > >
> > > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > > ---
> > > .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 18
> > > ++++++++++++++++-- 1 file changed, 16 insertions(+), 2 deletions(-)
> > >
> > > diff --git
> > > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > index 5240487dfe50..292b05d9ed08 100644 ---
> > > a/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > +++
> > > b/Documentation/devicetree/bindings/pinctrl/allwinner,sun4i-a10-pinctrl.yaml
> > > @@ -53,6 +53,8 @@ properties:
> > > - allwinner,sun50i-h5-pinctrl
> > > - allwinner,sun50i-h6-pinctrl
> > > - allwinner,sun50i-h6-r-pinctrl
> > > + - allwinner,sun50i-h616-pinctrl
> > > + - allwinner,sun50i-h616-r-pinctrl
> > > - allwinner,suniv-f1c100s-pinctrl
> > > - nextthing,gr8-pinctrl
> > >
> > > @@ -61,7 +63,7 @@ properties:
> > >
> > > interrupts:
> > > minItems: 1
> > > - maxItems: 7
> > > + maxItems: 8
> > > description:
> > > One interrupt per external interrupt bank supported on the
> > > controller, sorted by bank number ascending order.
> > > @@ -91,7 +93,7 @@ properties:
> > > bank found in the controller
> > > $ref: /schemas/types.yaml#/definitions/uint32-array
> > > minItems: 1
> > > - maxItems: 5
> > > + maxItems: 8
> > >
> > > patternProperties:
> > > # It's pretty scary, but the basic idea is that:
> > > @@ -145,6 +147,18 @@ allOf:
> > > # boards are defining it at the moment so it would generate a
> > > lot of # warnings.
> > >
> > > + - if:
> > > + properties:
> > > + compatible:
> > > + enum:
> > > + - allwinner,sun50i-h616-pinctrl
> > > +
> > > + then:
> > > + properties:
> > > + interrupts:
> > > + minItems: 8
> > > + maxItems: 8
> > > +
> >
> > You don't need to have both if they are equals, and in this particular
>
> Mmh, but all the other compatibles have both equal, so what would be
> the recommended way to describe this? Just minItems? I don't find a
> good explanation at the moment how to handle an explicit number, other
> than by enumerating the items explicitly.
This is where the magic happens:
https://github.com/devicetree-org/dt-schema/blob/master/dtschema/lib.py#L258
So, if there's an items property, it will expand minItems and maxItems
according to the length of the list. Else, it will see if there's either
minItems and maxItems and set the other one if it's missing.
In this case, minItems and maxItems are equals, so you could just fill
one of them
> > case we already check that the maximum is 8 so there's no need to
> > repeat that check here.
>
> Are you referring to the overall "maxItems: 8" above, in the 2nd hunk?
> While this will become redundant, this is apparently prone to changes
> (as only "7" would be redundant at the moment), so I would rather not
> rely on a global limit.
Yeah, my point was that since the upper schema checks for the interrupts
array length to be between 1 and 8, there's no need to specify a max of
8, the upper schema has it covered.
You're right that the max is increased regularly, however we can still
rely on the above logic to fill maxItems to 8 anyway
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 03/21] pinctrl: sunxi: Add support for the Allwinner H616 pin controller
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, linux-gpio
Port A is used for an internal connection to some analogue circuitry
which looks like an AC200 IP (as in the H6), though this is not
mentioned in the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/pinctrl/sunxi/Kconfig | 5 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++++++++++++++
3 files changed, 554 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 593293584ecc..73e88ce71a48 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -119,4 +119,9 @@ config PINCTRL_SUN50I_H6_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H616
+ bool "Support for the Allwinner H616 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 8b7ff0dc3bdf..5359327a3c8f 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -23,5 +23,6 @@ obj-$(CONFIG_PINCTRL_SUN8I_V3S) += pinctrl-sun8i-v3s.o
obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN50I_H6) += pinctrl-sun50i-h6.o
obj-$(CONFIG_PINCTRL_SUN50I_H6_R) += pinctrl-sun50i-h6-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_H616) += pinctrl-sun50i-h616.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
new file mode 100644
index 000000000000..02ff80bf163a
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Allwinner H616 SoC pinctrl driver.
+ *
+ * Copyright (C) 2020 Arm Ltd.
+ * based on the H6 pinctrl driver
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin h616_pins[] = {
+ /* Internal connection to the AC200 part */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ECRS_DV */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x2, "emac1")), /* EMDC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x2, "emac1")), /* EMDIO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x2, "i2c3")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x2, "i2c3")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x2, "pwm5")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PC_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PC_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PC_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PC_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PC_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PC_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PC_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PC_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PC_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PC_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PC_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PC_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PC_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PC_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)), /* PC_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)), /* PC_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)), /* PC_EINT16 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)), /* PF_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)), /* PF_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)), /* PF_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)), /* PF_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)), /* PF_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)), /* PF_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)), /* PF_EINT6 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION(0x3, "clock"), /* PLL_LOCK_DEBUG */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "clock"), /* X32KFOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)), /* PG_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 14)), /* PG_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 15)), /* PG_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 16)), /* PG_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 17)), /* PG_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 18)), /* PG_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 19)), /* PG_EINT19 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x4, "pwm3"),
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)), /* PH_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x4, "pwm4"),
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)), /* PH_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart5"), /* TX */
+ SUNXI_FUNCTION(0x3, "spdif"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "pwm2"),
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)), /* PH_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart5"), /* RX */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)), /* PH_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)), /* PH_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS0 */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)), /* PH_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)), /* PH_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* SYNC */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), /* PH_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DO0 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x5, "h_i2s3"), /* DI1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)), /* PH_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DI0 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS1 */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DO1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), /* PH_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "ir_rx"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), /* PH_EINT10 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD3 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HSCL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 0)), /* PI_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD2 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HSDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 1)), /* PI_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD1 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HCEC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 2)), /* PI_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD0 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* DO0 */
+ SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DI1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 3)), /* PI_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXCK */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* DI0 */
+ SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DO1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 4)), /* PI_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXCTL */
+ SUNXI_FUNCTION(0x3, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* CLK */
+ SUNXI_FUNCTION(0x5, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 5)), /* PI_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ENULL */
+ SUNXI_FUNCTION(0x3, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* ERR */
+ SUNXI_FUNCTION(0x5, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 6)), /* PI_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD3 */
+ SUNXI_FUNCTION(0x3, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* SYNC */
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 7)), /* PI_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD2 */
+ SUNXI_FUNCTION(0x3, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* DVLD */
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 8)), /* PI_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD1 */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D0 */
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 9)), /* PI_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD0 */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D1 */
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 10)), /* PI_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXCK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D2 */
+ SUNXI_FUNCTION(0x5, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 11)), /* PI_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXCTL */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D3 */
+ SUNXI_FUNCTION(0x5, "pwm2"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 12)), /* PI_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ECLKIN */
+ SUNXI_FUNCTION(0x3, "uart4"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D4 */
+ SUNXI_FUNCTION(0x5, "pwm3"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 13)), /* PI_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* MDC */
+ SUNXI_FUNCTION(0x3, "uart4"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D5 */
+ SUNXI_FUNCTION(0x5, "pwm4"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 14)), /* PI_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* MDIO */
+ SUNXI_FUNCTION(0x3, "uart4"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D6 */
+ SUNXI_FUNCTION(0x5, "clock"), /* CLK_FANOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 15)), /* PI_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* EPHY_CLK */
+ SUNXI_FUNCTION(0x3, "uart4"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D7 */
+ SUNXI_FUNCTION(0x5, "clock"), /* CLK_FANOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 16)), /* PI_EINT16 */
+};
+static const unsigned int h616_irq_bank_map[] = { 0, 2, 3, 4, 5, 6, 7, 8 };
+
+static const struct sunxi_pinctrl_desc h616_pinctrl_data = {
+ .pins = h616_pins,
+ .npins = ARRAY_SIZE(h616_pins),
+ .irq_banks = ARRAY_SIZE(h616_irq_bank_map),
+ .irq_bank_map = h616_irq_bank_map,
+ .irq_read_needs_mux = true,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int h616_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &h616_pinctrl_data);
+}
+
+static const struct of_device_id h616_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h616-pinctrl", },
+ {}
+};
+
+static struct platform_driver h616_pinctrl_driver = {
+ .probe = h616_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h616-pinctrl",
+ .of_match_table = h616_pinctrl_match,
+ },
+};
+builtin_platform_driver(h616_pinctrl_driver);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 03/21] pinctrl: sunxi: Add support for the Allwinner H616 pin controller
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel, linux-gpio,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
Port A is used for an internal connection to some analogue circuitry
which looks like an AC200 IP (as in the H6), though this is not
mentioned in the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/pinctrl/sunxi/Kconfig | 5 +
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++++++++++++++
3 files changed, 554 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 593293584ecc..73e88ce71a48 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -119,4 +119,9 @@ config PINCTRL_SUN50I_H6_R
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H616
+ bool "Support for the Allwinner H616 PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 8b7ff0dc3bdf..5359327a3c8f 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -23,5 +23,6 @@ obj-$(CONFIG_PINCTRL_SUN8I_V3S) += pinctrl-sun8i-v3s.o
obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN50I_H6) += pinctrl-sun50i-h6.o
obj-$(CONFIG_PINCTRL_SUN50I_H6_R) += pinctrl-sun50i-h6-r.o
+obj-$(CONFIG_PINCTRL_SUN50I_H616) += pinctrl-sun50i-h616.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
new file mode 100644
index 000000000000..02ff80bf163a
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Allwinner H616 SoC pinctrl driver.
+ *
+ * Copyright (C) 2020 Arm Ltd.
+ * based on the H6 pinctrl driver
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin h616_pins[] = {
+ /* Internal connection to the AC200 part */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 0),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 1),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 2),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ECRS_DV */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 3),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ERXERR */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 4),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXD1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 5),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXD0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 6),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 7),
+ SUNXI_FUNCTION(0x2, "emac1")), /* ETXEN */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 8),
+ SUNXI_FUNCTION(0x2, "emac1")), /* EMDC */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 9),
+ SUNXI_FUNCTION(0x2, "emac1")), /* EMDIO */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 10),
+ SUNXI_FUNCTION(0x2, "i2c3")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 11),
+ SUNXI_FUNCTION(0x2, "i2c3")), /* SDA */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(A, 12),
+ SUNXI_FUNCTION(0x2, "pwm5")),
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* WE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* DS */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 0)), /* PC_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* ALE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* RST */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 1)), /* PC_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CLE */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MOSI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 2)), /* PC_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 3)), /* PC_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* CE0 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* MISO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 4)), /* PC_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RE */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 5)), /* PC_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 6)), /* PC_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* RB1 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* CS1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 7)), /* PC_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ7 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 8)), /* PC_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ6 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D4 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 9)), /* PC_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ5 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 10)), /* PC_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ4 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D5 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 11)), /* PC_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 12)), /* PC_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ3 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 13)), /* PC_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ2 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D6 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 14)), /* PC_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ1 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D2 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* WP */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 15)), /* PC_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(C, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "nand0"), /* DQ0 */
+ SUNXI_FUNCTION(0x3, "mmc2"), /* D7 */
+ SUNXI_FUNCTION(0x4, "spi0"), /* HOLD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 1, 16)), /* PC_EINT16 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D1 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 0)), /* PF_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D0 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DI */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 1)), /* PF_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CLK */
+ SUNXI_FUNCTION(0x3, "uart0"), /* TX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 2)), /* PF_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* CMD */
+ SUNXI_FUNCTION(0x3, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 3)), /* PF_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D3 */
+ SUNXI_FUNCTION(0x3, "uart0"), /* RX */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 4)), /* PF_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc0"), /* D2 */
+ SUNXI_FUNCTION(0x3, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 5)), /* PF_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(F, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 4, 6)), /* PF_EINT6 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 0)), /* PG_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* CMD */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 1)), /* PG_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 2)), /* PG_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 3)), /* PG_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D2 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 4)), /* PG_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "mmc1"), /* D3 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 5)), /* PG_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* TX */
+ SUNXI_FUNCTION(0x4, "jtag"), /* MS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 6)), /* PG_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RX */
+ SUNXI_FUNCTION(0x4, "jtag"), /* CK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 7)), /* PG_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* RTS */
+ SUNXI_FUNCTION(0x3, "clock"), /* PLL_LOCK_DEBUG */
+ SUNXI_FUNCTION(0x4, "jtag"), /* DO */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 8)), /* PG_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart1"), /* CTS */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 9)), /* PG_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* MCLK */
+ SUNXI_FUNCTION(0x3, "clock"), /* X32KFOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), /* PG_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* BCLK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 11)), /* PG_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* SYNC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 12)), /* PG_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* DOUT */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 13)), /* PG_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "h_i2s2"), /* DIN */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 14)), /* PG_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 15)), /* PG_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 16)), /* PG_EINT16 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 17),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 17)), /* PG_EINT17 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 18),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 18)), /* PG_EINT18 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 19),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 19)), /* PG_EINT19 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* TX */
+ SUNXI_FUNCTION(0x4, "pwm3"),
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 0)), /* PH_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart0"), /* RX */
+ SUNXI_FUNCTION(0x4, "pwm4"),
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 1)), /* PH_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart5"), /* TX */
+ SUNXI_FUNCTION(0x3, "spdif"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "pwm2"),
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 2)), /* PH_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart5"), /* RX */
+ SUNXI_FUNCTION(0x4, "pwm1"),
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 3)), /* PH_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "spdif"), /* OUT */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 4)), /* PH_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* MCLK */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS0 */
+ SUNXI_FUNCTION(0x5, "i2c3"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 5)), /* PH_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* BCLK */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CLK */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 6)), /* PH_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* SYNC */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MOSI */
+ SUNXI_FUNCTION(0x5, "i2c4"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 7)), /* PH_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DO0 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* MISO */
+ SUNXI_FUNCTION(0x5, "h_i2s3"), /* DI1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 8)), /* PH_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DI0 */
+ SUNXI_FUNCTION(0x4, "spi1"), /* CS1 */
+ SUNXI_FUNCTION(0x3, "h_i2s3"), /* DO1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 9)), /* PH_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(H, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "ir_rx"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 6, 10)), /* PH_EINT10 */
+ /* Hole */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD3 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* CLK */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* MCLK */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HSCL */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 0)), /* PI_EINT0 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD2 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA0 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* BCLK */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HSDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 1)), /* PI_EINT1 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 2),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD1 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA1 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* SYNC */
+ SUNXI_FUNCTION(0x5, "hdmi"), /* HCEC */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 2)), /* PI_EINT2 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXD0 */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA2 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* DO0 */
+ SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DI1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 3)), /* PI_EINT3 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 4),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXCK */
+ SUNXI_FUNCTION(0x3, "dmic"), /* DATA3 */
+ SUNXI_FUNCTION(0x4, "h_i2s0"), /* DI0 */
+ SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DO1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 4)), /* PI_EINT4 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 5),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ERXCTL */
+ SUNXI_FUNCTION(0x3, "uart2"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* CLK */
+ SUNXI_FUNCTION(0x5, "i2c0"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 5)), /* PI_EINT5 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 6),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ENULL */
+ SUNXI_FUNCTION(0x3, "uart2"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* ERR */
+ SUNXI_FUNCTION(0x5, "i2c0"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 6)), /* PI_EINT6 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 7),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD3 */
+ SUNXI_FUNCTION(0x3, "uart2"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* SYNC */
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 7)), /* PI_EINT7 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 8),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD2 */
+ SUNXI_FUNCTION(0x3, "uart2"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* DVLD */
+ SUNXI_FUNCTION(0x5, "i2c1"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 8)), /* PI_EINT8 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 9),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD1 */
+ SUNXI_FUNCTION(0x3, "uart3"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D0 */
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SCK */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 9)), /* PI_EINT9 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 10),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXD0 */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D1 */
+ SUNXI_FUNCTION(0x5, "i2c2"), /* SDA */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 10)), /* PI_EINT10 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 11),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXCK */
+ SUNXI_FUNCTION(0x3, "uart3"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D2 */
+ SUNXI_FUNCTION(0x5, "pwm1"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 11)), /* PI_EINT11 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 12),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ETXCTL */
+ SUNXI_FUNCTION(0x3, "uart3"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D3 */
+ SUNXI_FUNCTION(0x5, "pwm2"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 12)), /* PI_EINT12 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 13),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* ECLKIN */
+ SUNXI_FUNCTION(0x3, "uart4"), /* TX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D4 */
+ SUNXI_FUNCTION(0x5, "pwm3"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 13)), /* PI_EINT13 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 14),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* MDC */
+ SUNXI_FUNCTION(0x3, "uart4"), /* RX */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D5 */
+ SUNXI_FUNCTION(0x5, "pwm4"),
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 14)), /* PI_EINT14 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 15),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* MDIO */
+ SUNXI_FUNCTION(0x3, "uart4"), /* RTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D6 */
+ SUNXI_FUNCTION(0x5, "clock"), /* CLK_FANOUT0 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 15)), /* PI_EINT15 */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 16),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x2, "emac0"), /* EPHY_CLK */
+ SUNXI_FUNCTION(0x3, "uart4"), /* CTS */
+ SUNXI_FUNCTION(0x4, "ts0"), /* D7 */
+ SUNXI_FUNCTION(0x5, "clock"), /* CLK_FANOUT1 */
+ SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 16)), /* PI_EINT16 */
+};
+static const unsigned int h616_irq_bank_map[] = { 0, 2, 3, 4, 5, 6, 7, 8 };
+
+static const struct sunxi_pinctrl_desc h616_pinctrl_data = {
+ .pins = h616_pins,
+ .npins = ARRAY_SIZE(h616_pins),
+ .irq_banks = ARRAY_SIZE(h616_irq_bank_map),
+ .irq_bank_map = h616_irq_bank_map,
+ .irq_read_needs_mux = true,
+ .io_bias_cfg_variant = BIAS_VOLTAGE_PIO_POW_MODE_SEL,
+};
+
+static int h616_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev, &h616_pinctrl_data);
+}
+
+static const struct of_device_id h616_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h616-pinctrl", },
+ {}
+};
+
+static struct platform_driver h616_pinctrl_driver = {
+ .probe = h616_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h616-pinctrl",
+ .of_match_table = h616_pinctrl_match,
+ },
+};
+builtin_platform_driver(h616_pinctrl_driver);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 03/21] pinctrl: sunxi: Add support for the Allwinner H616 pin controller
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 9:44 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:44 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
linux-gpio
[-- Attachment #1: Type: text/plain, Size: 952 bytes --]
On Fri, Dec 11, 2020 at 01:19:16AM +0000, Andre Przywara wrote:
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "h_i2s2"), /* MCLK */
> + SUNXI_FUNCTION(0x3, "clock"), /* X32KFOUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), /* PG_EINT10 */
It looks like there's no i2s vs h_i2s issue anymore? Maybe we can just
do s/h_i2s/i2s
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac0"), /* ERXD0 */
> + SUNXI_FUNCTION(0x3, "dmic"), /* DATA2 */
> + SUNXI_FUNCTION(0x4, "h_i2s0"), /* DO0 */
> + SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DI1 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 3)), /* PI_EINT3 */
The way we dealt with this for the A100 is that we put the function as a
suffix which is more natural, so h_i2s0_dout0 and h_i2s0_din1
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 03/21] pinctrl: sunxi: Add support for the Allwinner H616 pin controller
@ 2020-12-14 9:44 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:44 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, Yangtao Li, Linus Walleij,
linux-sunxi, linux-kernel, linux-gpio, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 952 bytes --]
On Fri, Dec 11, 2020 at 01:19:16AM +0000, Andre Przywara wrote:
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(G, 10),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "h_i2s2"), /* MCLK */
> + SUNXI_FUNCTION(0x3, "clock"), /* X32KFOUT */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 5, 10)), /* PG_EINT10 */
It looks like there's no i2s vs h_i2s issue anymore? Maybe we can just
do s/h_i2s/i2s
> + SUNXI_PIN(SUNXI_PINCTRL_PIN(I, 3),
> + SUNXI_FUNCTION(0x0, "gpio_in"),
> + SUNXI_FUNCTION(0x1, "gpio_out"),
> + SUNXI_FUNCTION(0x2, "emac0"), /* ERXD0 */
> + SUNXI_FUNCTION(0x3, "dmic"), /* DATA2 */
> + SUNXI_FUNCTION(0x4, "h_i2s0"), /* DO0 */
> + SUNXI_FUNCTION(0x5, "h_i2s0_a"), /* DI1 */
> + SUNXI_FUNCTION_IRQ_BANK(0x6, 7, 3)), /* PI_EINT3 */
The way we dealt with this for the A100 is that we put the function as a
suffix which is more natural, so h_i2s0_dout0 and h_i2s0_din1
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 04/21] pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, linux-gpio
There are only two pins left now, used to connect to the PMIC via I2C.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
drivers/pinctrl/sunxi/Kconfig | 5 ++
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +++++++++++++++++++
3 files changed, 60 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 73e88ce71a48..33751a6a0757 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -124,4 +124,9 @@ config PINCTRL_SUN50I_H616
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H616_R
+ bool "Support for the Allwinner H616 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 5359327a3c8f..d3440c42b9d6 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -24,5 +24,6 @@ obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN50I_H6) += pinctrl-sun50i-h6.o
obj-$(CONFIG_PINCTRL_SUN50I_H6_R) += pinctrl-sun50i-h6-r.o
obj-$(CONFIG_PINCTRL_SUN50I_H616) += pinctrl-sun50i-h616.o
+obj-$(CONFIG_PINCTRL_SUN50I_H616_R) += pinctrl-sun50i-h616-r.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
new file mode 100644
index 000000000000..52783dd98b18
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Allwinner H616 R_PIO pin controller driver
+ *
+ * Copyright (C) 2020 Arm Ltd.
+ * Based on former work, which is:
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/reset.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun50i_h616_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_i2c")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_i2c")), /* SDA */
+};
+
+static const struct sunxi_pinctrl_desc sun50i_h616_r_pinctrl_data = {
+ .pins = sun50i_h616_r_pins,
+ .npins = ARRAY_SIZE(sun50i_h616_r_pins),
+ .pin_base = PL_BASE,
+};
+
+static int sun50i_h616_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun50i_h616_r_pinctrl_data);
+}
+
+static const struct of_device_id sun50i_h616_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h616-r-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun50i_h616_r_pinctrl_driver = {
+ .probe = sun50i_h616_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h616-r-pinctrl",
+ .of_match_table = sun50i_h616_r_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun50i_h616_r_pinctrl_driver);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 04/21] pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel, linux-gpio,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
There are only two pins left now, used to connect to the PMIC via I2C.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
---
drivers/pinctrl/sunxi/Kconfig | 5 ++
drivers/pinctrl/sunxi/Makefile | 1 +
drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +++++++++++++++++++
3 files changed, 60 insertions(+)
create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
diff --git a/drivers/pinctrl/sunxi/Kconfig b/drivers/pinctrl/sunxi/Kconfig
index 73e88ce71a48..33751a6a0757 100644
--- a/drivers/pinctrl/sunxi/Kconfig
+++ b/drivers/pinctrl/sunxi/Kconfig
@@ -124,4 +124,9 @@ config PINCTRL_SUN50I_H616
default ARM64 && ARCH_SUNXI
select PINCTRL_SUNXI
+config PINCTRL_SUN50I_H616_R
+ bool "Support for the Allwinner H616 R-PIO"
+ default ARM64 && ARCH_SUNXI
+ select PINCTRL_SUNXI
+
endif
diff --git a/drivers/pinctrl/sunxi/Makefile b/drivers/pinctrl/sunxi/Makefile
index 5359327a3c8f..d3440c42b9d6 100644
--- a/drivers/pinctrl/sunxi/Makefile
+++ b/drivers/pinctrl/sunxi/Makefile
@@ -24,5 +24,6 @@ obj-$(CONFIG_PINCTRL_SUN50I_H5) += pinctrl-sun50i-h5.o
obj-$(CONFIG_PINCTRL_SUN50I_H6) += pinctrl-sun50i-h6.o
obj-$(CONFIG_PINCTRL_SUN50I_H6_R) += pinctrl-sun50i-h6-r.o
obj-$(CONFIG_PINCTRL_SUN50I_H616) += pinctrl-sun50i-h616.o
+obj-$(CONFIG_PINCTRL_SUN50I_H616_R) += pinctrl-sun50i-h616-r.o
obj-$(CONFIG_PINCTRL_SUN9I_A80) += pinctrl-sun9i-a80.o
obj-$(CONFIG_PINCTRL_SUN9I_A80_R) += pinctrl-sun9i-a80-r.o
diff --git a/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
new file mode 100644
index 000000000000..52783dd98b18
--- /dev/null
+++ b/drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Allwinner H616 R_PIO pin controller driver
+ *
+ * Copyright (C) 2020 Arm Ltd.
+ * Based on former work, which is:
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/reset.h>
+
+#include "pinctrl-sunxi.h"
+
+static const struct sunxi_desc_pin sun50i_h616_r_pins[] = {
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 0),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_i2c")), /* SCK */
+ SUNXI_PIN(SUNXI_PINCTRL_PIN(L, 1),
+ SUNXI_FUNCTION(0x0, "gpio_in"),
+ SUNXI_FUNCTION(0x1, "gpio_out"),
+ SUNXI_FUNCTION(0x3, "s_i2c")), /* SDA */
+};
+
+static const struct sunxi_pinctrl_desc sun50i_h616_r_pinctrl_data = {
+ .pins = sun50i_h616_r_pins,
+ .npins = ARRAY_SIZE(sun50i_h616_r_pins),
+ .pin_base = PL_BASE,
+};
+
+static int sun50i_h616_r_pinctrl_probe(struct platform_device *pdev)
+{
+ return sunxi_pinctrl_init(pdev,
+ &sun50i_h616_r_pinctrl_data);
+}
+
+static const struct of_device_id sun50i_h616_r_pinctrl_match[] = {
+ { .compatible = "allwinner,sun50i-h616-r-pinctrl", },
+ {}
+};
+
+static struct platform_driver sun50i_h616_r_pinctrl_driver = {
+ .probe = sun50i_h616_r_pinctrl_probe,
+ .driver = {
+ .name = "sun50i-h616-r-pinctrl",
+ .of_match_table = sun50i_h616_r_pinctrl_match,
+ },
+};
+builtin_platform_driver(sun50i_h616_r_pinctrl_driver);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 05/21] dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, linux-clk, devicetree
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 3b45344ed758..b7e891803bb4 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -41,6 +41,8 @@ properties:
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
+ - allwinner,sun50i-h616-ccu
+ - allwinner,sun50i-h616-r-ccu
- allwinner,suniv-f1c100s-ccu
- nextthing,gr8-ccu
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 05/21] dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-clk, Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 3b45344ed758..b7e891803bb4 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -41,6 +41,8 @@ properties:
- allwinner,sun50i-h5-ccu
- allwinner,sun50i-h6-ccu
- allwinner,sun50i-h6-r-ccu
+ - allwinner,sun50i-h616-ccu
+ - allwinner,sun50i-h616-r-ccu
- allwinner,suniv-f1c100s-ccu
- nextthing,gr8-ccu
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 05/21] dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:53 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:53 UTC (permalink / raw)
To: Andre Przywara
Cc: Clément Péron, Yangtao Li, linux-arm-kernel,
devicetree, Michael Turquette, linux-clk, Stephen Boyd,
Chen-Yu Tsai, Jernej Skrabec, Linus Walleij, Icenowy Zheng,
Maxime Ripard, linux-kernel, linux-sunxi, Shuosheng Huang
On Fri, 11 Dec 2020 01:19:18 +0000, Andre Przywara wrote:
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 05/21] dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner H616
@ 2020-12-14 22:53 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:53 UTC (permalink / raw)
To: Andre Przywara
Cc: devicetree, Jernej Skrabec, Linus Walleij, Yangtao Li,
Michael Turquette, linux-sunxi, linux-kernel, Maxime Ripard,
Stephen Boyd, Chen-Yu Tsai, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-clk, linux-arm-kernel
On Fri, 11 Dec 2020 01:19:18 +0000, Andre Przywara wrote:
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml | 2 ++
> 1 file changed, 2 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 06/21] clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, Philipp Zabel, linux-clk
The clocks itself are identical to the H6 R-CCU, it's just that the H616
has not all of them implemented (or connected).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +++++++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
3 files changed, 49 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index ce5f5847d5d3..feeb8d2074ee 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -33,7 +33,7 @@ config SUN50I_H6_CCU
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
config SUN50I_H6_R_CCU
- bool "Support for the Allwinner H6 PRCM CCU"
+ bool "Support for the Allwinner H6 and H616 PRCM CCU"
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index 50f8d1bc7046..0ca35f383975 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -136,6 +136,15 @@ static struct ccu_common *sun50i_h6_r_ccu_clks[] = {
&w1_clk.common,
};
+static struct ccu_common *sun50i_h616_r_ccu_clks[] = {
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb2_i2c_clk.common,
+ &r_apb1_ir_clk.common,
+ &ir_clk.common,
+};
+
static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
.hws = {
[CLK_AR100] = &ar100_clk.common.hw,
@@ -152,7 +161,20 @@ static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
[CLK_IR] = &ir_clk.common.hw,
[CLK_W1] = &w1_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H6,
+};
+
+static struct clk_hw_onecell_data sun50i_h616_r_hw_clks = {
+ .hws = {
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB2_I2C] = &r_apb2_i2c_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_clk.common.hw,
+ [CLK_IR] = &ir_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H616,
};
static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
@@ -165,6 +187,12 @@ static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
[RST_R_APB1_W1] = { 0x1ec, BIT(16) },
};
+static struct ccu_reset_map sun50i_h616_r_ccu_resets[] = {
+ [RST_R_APB1_TWD] = { 0x12c, BIT(16) },
+ [RST_R_APB2_I2C] = { 0x19c, BIT(16) },
+ [RST_R_APB1_IR] = { 0x1cc, BIT(16) },
+};
+
static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
.ccu_clks = sun50i_h6_r_ccu_clks,
.num_ccu_clks = ARRAY_SIZE(sun50i_h6_r_ccu_clks),
@@ -175,6 +203,16 @@ static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
.num_resets = ARRAY_SIZE(sun50i_h6_r_ccu_resets),
};
+static const struct sunxi_ccu_desc sun50i_h616_r_ccu_desc = {
+ .ccu_clks = sun50i_h616_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h616_r_ccu_clks),
+
+ .hw_clks = &sun50i_h616_r_hw_clks,
+
+ .resets = sun50i_h616_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h616_r_ccu_resets),
+};
+
static void __init sunxi_r_ccu_init(struct device_node *node,
const struct sunxi_ccu_desc *desc)
{
@@ -195,3 +233,10 @@ static void __init sun50i_h6_r_ccu_setup(struct device_node *node)
}
CLK_OF_DECLARE(sun50i_h6_r_ccu, "allwinner,sun50i-h6-r-ccu",
sun50i_h6_r_ccu_setup);
+
+static void __init sun50i_h616_r_ccu_setup(struct device_node *node)
+{
+ sunxi_r_ccu_init(node, &sun50i_h616_r_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h616_r_ccu, "allwinner,sun50i-h616-r-ccu",
+ sun50i_h616_r_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
index 782117dc0b28..128302696ca1 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
@@ -14,6 +14,7 @@
#define CLK_R_APB2 3
-#define CLK_NUMBER (CLK_W1 + 1)
+#define CLK_NUMBER_H6 (CLK_W1 + 1)
+#define CLK_NUMBER_H616 (CLK_IR + 1)
#endif /* _CCU_SUN50I_H6_R_H */
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 06/21] clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel, linux-clk,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Philipp Zabel, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
The clocks itself are identical to the H6 R-CCU, it's just that the H616
has not all of them implemented (or connected).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/clk/sunxi-ng/Kconfig | 2 +-
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +++++++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
3 files changed, 49 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index ce5f5847d5d3..feeb8d2074ee 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -33,7 +33,7 @@ config SUN50I_H6_CCU
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
config SUN50I_H6_R_CCU
- bool "Support for the Allwinner H6 PRCM CCU"
+ bool "Support for the Allwinner H6 and H616 PRCM CCU"
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
index 50f8d1bc7046..0ca35f383975 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c
@@ -136,6 +136,15 @@ static struct ccu_common *sun50i_h6_r_ccu_clks[] = {
&w1_clk.common,
};
+static struct ccu_common *sun50i_h616_r_ccu_clks[] = {
+ &r_apb1_clk.common,
+ &r_apb2_clk.common,
+ &r_apb1_twd_clk.common,
+ &r_apb2_i2c_clk.common,
+ &r_apb1_ir_clk.common,
+ &ir_clk.common,
+};
+
static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
.hws = {
[CLK_AR100] = &ar100_clk.common.hw,
@@ -152,7 +161,20 @@ static struct clk_hw_onecell_data sun50i_h6_r_hw_clks = {
[CLK_IR] = &ir_clk.common.hw,
[CLK_W1] = &w1_clk.common.hw,
},
- .num = CLK_NUMBER,
+ .num = CLK_NUMBER_H6,
+};
+
+static struct clk_hw_onecell_data sun50i_h616_r_hw_clks = {
+ .hws = {
+ [CLK_R_AHB] = &r_ahb_clk.hw,
+ [CLK_R_APB1] = &r_apb1_clk.common.hw,
+ [CLK_R_APB2] = &r_apb2_clk.common.hw,
+ [CLK_R_APB1_TWD] = &r_apb1_twd_clk.common.hw,
+ [CLK_R_APB2_I2C] = &r_apb2_i2c_clk.common.hw,
+ [CLK_R_APB1_IR] = &r_apb1_ir_clk.common.hw,
+ [CLK_IR] = &ir_clk.common.hw,
+ },
+ .num = CLK_NUMBER_H616,
};
static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
@@ -165,6 +187,12 @@ static struct ccu_reset_map sun50i_h6_r_ccu_resets[] = {
[RST_R_APB1_W1] = { 0x1ec, BIT(16) },
};
+static struct ccu_reset_map sun50i_h616_r_ccu_resets[] = {
+ [RST_R_APB1_TWD] = { 0x12c, BIT(16) },
+ [RST_R_APB2_I2C] = { 0x19c, BIT(16) },
+ [RST_R_APB1_IR] = { 0x1cc, BIT(16) },
+};
+
static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
.ccu_clks = sun50i_h6_r_ccu_clks,
.num_ccu_clks = ARRAY_SIZE(sun50i_h6_r_ccu_clks),
@@ -175,6 +203,16 @@ static const struct sunxi_ccu_desc sun50i_h6_r_ccu_desc = {
.num_resets = ARRAY_SIZE(sun50i_h6_r_ccu_resets),
};
+static const struct sunxi_ccu_desc sun50i_h616_r_ccu_desc = {
+ .ccu_clks = sun50i_h616_r_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h616_r_ccu_clks),
+
+ .hw_clks = &sun50i_h616_r_hw_clks,
+
+ .resets = sun50i_h616_r_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h616_r_ccu_resets),
+};
+
static void __init sunxi_r_ccu_init(struct device_node *node,
const struct sunxi_ccu_desc *desc)
{
@@ -195,3 +233,10 @@ static void __init sun50i_h6_r_ccu_setup(struct device_node *node)
}
CLK_OF_DECLARE(sun50i_h6_r_ccu, "allwinner,sun50i-h6-r-ccu",
sun50i_h6_r_ccu_setup);
+
+static void __init sun50i_h616_r_ccu_setup(struct device_node *node)
+{
+ sunxi_r_ccu_init(node, &sun50i_h616_r_ccu_desc);
+}
+CLK_OF_DECLARE(sun50i_h616_r_ccu, "allwinner,sun50i-h616-r-ccu",
+ sun50i_h616_r_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
index 782117dc0b28..128302696ca1 100644
--- a/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h
@@ -14,6 +14,7 @@
#define CLK_R_APB2 3
-#define CLK_NUMBER (CLK_W1 + 1)
+#define CLK_NUMBER_H6 (CLK_W1 + 1)
+#define CLK_NUMBER_H616 (CLK_IR + 1)
#endif /* _CCU_SUN50I_H6_R_H */
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 07/21] clk: sunxi-ng: Add support for the Allwinner H616 CCU
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, Philipp Zabel, linux-clk
While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.
Derived from the H6 clock driver, and adjusted according to the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/clk/sunxi-ng/Kconfig | 5 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150 +++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
include/dt-bindings/reset/sun50i-h616-ccu.h | 70 ++
6 files changed, 1397 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index feeb8d2074ee..cd46d8853876 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -32,6 +32,11 @@ config SUN50I_H6_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_H616_CCU
+ bool "Support for the Allwinner H616 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_R_CCU
bool "Support for the Allwinner H6 and H616 PRCM CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 3eb5cff40eac..96c324306d97 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
+obj-$(CONFIG_SUN50I_H616_CCU) += ccu-sun50i-h616.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
new file mode 100644
index 000000000000..19db5636a80d
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
@@ -0,0 +1,1150 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Arm Ltd.
+ * Based on the H6 CCU driver, which is:
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-h616.h"
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_H616_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "osc24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_H616_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_DDR1_REG 0x018
+static struct ccu_nkmp pll_ddr1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x018,
+ .hw.init = CLK_HW_INIT("pll-ddr1", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_H616_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_DE_REG 0x060
+static struct ccu_nkmp pll_de_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x060,
+ .hw.init = CLK_HW_INIT("pll-de", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * TODO: Determine SDM settings for the audio PLL. The manual suggests
+ * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b
+ * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2,
+ * pattern=0xe001288c for 22.5792 MHz.
+ * This clashes with our fixed PLL_POST_DIV_P.
+ */
+#define SUN50I_H616_PLL_AUDIO_REG 0x078
+static struct ccu_nm pll_audio_hs_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .common = {
+ .reg = 0x078,
+ .hw.init = CLK_HW_INIT("pll-audio-hs", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "osc24M", "osc32k",
+ "iosc", "pll-cpux", "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "osc24M", "osc32k",
+ "iosc", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents,
+ 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "osc24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-ddr0", "pll-ddr1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-de", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
+ de_parents,
+ 0x620,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "psi-ahb1-ahb2",
+ 0x62c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d", de_parents, 0x630,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu0_parents[] = { "pll-gpu", "gpu1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu0_clk, "gpu0", gpu0_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_GATE(gpu1_clk, "gpu1", "pll-periph0-2x", 0x674,
+ 0, 2, /* M */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "osc24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 1, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1" };
+static struct ccu_div dram_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0x800,
+ .hw.init = CLK_HW_INIT_PARENTS("dram",
+ dram_parents,
+ &ccu_div_ops,
+ CLK_IS_CRITICAL),
+ },
+};
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_ts_clk, "mbus-ts", "mbus",
+ 0x804, BIT(3), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "osc24M", "pll-periph0",
+ "pll-periph1", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2", 0x90c, BIT(5), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2", 0x91c, BIT(4), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac0_clk, "bus-emac0", "ahb3", 0x97c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_emac1_clk, "bus-emac1", "ahb3", 0x97c, BIT(1), 0);
+
+static const char * const ts_parents[] = { "osc24M", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x9b0,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 1, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb3", 0x9bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio-1x", "pll-audio-2x",
+ "pll-audio-4x", "pll-audio-hs" };
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa20,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_1x_clk, "audio-codec-1x",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+static struct ccu_div audio_hub_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa60,
+ .hw.init = CLK_HW_INIT_PARENTS("audio-hub",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_audio_hub_clk, "bus-audio-hub", "apb1", 0xa6c, BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for the four USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_H616_USB0_CLK_REG 0xa70
+#define SUN50I_H616_USB1_CLK_REG 0xa74
+#define SUN50I_H616_USB2_CLK_REG 0xa78
+#define SUN50I_H616_USB3_CLK_REG 0xa7c
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc12M", 0xa78, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M", 0xa78, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc12M", 0xa7c, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy3_clk, "usb-phy3", "osc24M", 0xa7c, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb3", 0xa8c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_ohci3_clk, "bus-ohci3", "ahb3", 0xa8c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb3", 0xa8c, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_ehci3_clk, "bus-ehci3", "ahb3", 0xa8c, BIT(7), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_keyadc_clk, "bus-keyadc", "apb1", 0xa9c, BIT(0), 0);
+
+static const char * const hdmi_parents[] = { "pll-video0", "pll-video0-4x",
+ "pll-video2", "pll-video2-4x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents, 0xb00,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M", 0xb04, BIT(31), 0);
+
+static const char * const hdmi_cec_parents[] = { "osc32k", "pll-periph0-2x" };
+static const struct ccu_mux_fixed_prediv hdmi_cec_predivs[] = {
+ { .index = 1, .div = 36621 },
+};
+
+#define SUN50I_H616_HDMI_CEC_CLK_REG 0xb10
+static struct ccu_mux hdmi_cec_clk = {
+ .enable = BIT(31),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .fixed_predivs = hdmi_cec_predivs,
+ .n_predivs = ARRAY_SIZE(hdmi_cec_predivs),
+ },
+
+ .common = {
+ .reg = 0xb10,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("hdmi-cec",
+ hdmi_cec_parents,
+ &ccu_mux_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb3", 0xb1c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb3",
+ 0xb5c, BIT(0), 0);
+
+static const char * const tcon_tv_parents[] = { "pll-video0",
+ "pll-video0-4x",
+ "pll-video1",
+ "pll-video1-4x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv0_clk, "tcon-tv0",
+ tcon_tv_parents, 0xb80,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv1_clk, "tcon-tv1",
+ tcon_tv_parents, 0xb84,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tcon_tv0_clk, "bus-tcon-tv0", "ahb3",
+ 0xb9c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tcon_tv1_clk, "bus-tcon-tv1", "ahb3",
+ 0xb9c, BIT(1), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(tve0_clk, "tve0",
+ tcon_tv_parents, 0xbb0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb3",
+ 0xbbc, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb3",
+ 0xbbc, BIT(1), 0);
+
+static const char * const hdcp_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdcp_clk, "hdcp", hdcp_parents, 0xc40,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_hdcp_clk, "bus-hdcp", "ahb3", 0xc4c, BIT(0), 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static const struct clk_hw *clk_parent_pll_audio[] = {
+ &pll_audio_hs_clk.common.hw
+};
+
+/*
+ * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200
+ * rates can be set exactly in conjunction with sigma-delta modulation.
+ */
+static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x",
+ clk_parent_pll_audio,
+ 96, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x",
+ clk_parent_pll_audio,
+ 48, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x",
+ clk_parent_pll_audio,
+ 24, 1, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_periph0_parents[] = {
+ &pll_periph0_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph0_2x_clk, "pll-periph0-2x",
+ pll_periph0_parents,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_periph1_parents[] = {
+ &pll_periph1_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph1_2x_clk, "pll-periph1-2x",
+ pll_periph1_parents,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_video0_4x_clk, "pll-video0-4x",
+ &pll_video0_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video1_4x_clk, "pll-video1-4x",
+ &pll_video1_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video2_4x_clk, "pll-video2-4x",
+ &pll_video2_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_h616_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_ddr1_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_ve_clk.common,
+ &pll_de_clk.common,
+ &pll_audio_hs_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &deinterlace_clk.common,
+ &bus_deinterlace_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu0_clk.common,
+ &bus_gpu_clk.common,
+ &gpu1_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &dram_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_ts_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_uart5_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &bus_i2c4_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac0_clk.common,
+ &bus_emac1_clk.common,
+ &ts_clk.common,
+ &bus_ts_clk.common,
+ &bus_ths_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_1x_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &audio_hub_clk.common,
+ &bus_audio_hub_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_phy2_clk.common,
+ &usb_ohci3_clk.common,
+ &usb_phy3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_otg_clk.common,
+ &bus_keyadc_clk.common,
+ &hdmi_clk.common,
+ &hdmi_slow_clk.common,
+ &hdmi_cec_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_tcon_top_clk.common,
+ &tcon_tv0_clk.common,
+ &tcon_tv1_clk.common,
+ &bus_tcon_tv0_clk.common,
+ &bus_tcon_tv1_clk.common,
+ &tve0_clk.common,
+ &bus_tve_top_clk.common,
+ &bus_tve0_clk.common,
+ &hdcp_clk.common,
+ &bus_hdcp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_h616_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_DDR1] = &pll_ddr1_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_PLL_AUDIO_HS] = &pll_audio_hs_clk.common.hw,
+ [CLK_PLL_AUDIO_1X] = &pll_audio_1x_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU0] = &gpu0_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_GPU1] = &gpu1_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_TS] = &mbus_ts_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_UART5] = &bus_uart5_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_BUS_I2C4] = &bus_i2c4_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC0] = &bus_emac0_clk.common.hw,
+ [CLK_BUS_EMAC1] = &bus_emac1_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_CODEC_1X] = &audio_codec_1x_clk.common.hw,
+ [CLK_AUDIO_CODEC_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_AUDIO_HUB] = &audio_hub_clk.common.hw,
+ [CLK_BUS_AUDIO_HUB] = &bus_audio_hub_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_KEYADC] = &bus_keyadc_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
+ [CLK_HDMI_CEC] = &hdmi_cec_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_TCON_TOP] = &bus_tcon_top_clk.common.hw,
+ [CLK_TCON_TV0] = &tcon_tv0_clk.common.hw,
+ [CLK_TCON_TV1] = &tcon_tv1_clk.common.hw,
+ [CLK_BUS_TCON_TV0] = &bus_tcon_tv0_clk.common.hw,
+ [CLK_BUS_TCON_TV1] = &bus_tcon_tv1_clk.common.hw,
+ [CLK_TVE0] = &tve0_clk.common.hw,
+ [CLK_BUS_TVE_TOP] = &bus_tve_top_clk.common.hw,
+ [CLK_BUS_TVE0] = &bus_tve0_clk.common.hw,
+ [CLK_HDCP] = &hdcp_clk.common.hw,
+ [CLK_BUS_HDCP] = &bus_hdcp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_h616_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_DEINTERLACE] = { 0x62c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_IOMMU] = { 0x7bc, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_UART5] = { 0x90c, BIT(21) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_I2C4] = { 0x91c, BIT(20) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_EMAC0] = { 0x97c, BIT(16) },
+ [RST_BUS_EMAC1] = { 0x97c, BIT(17) },
+ [RST_BUS_TS] = { 0x9bc, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+ [RST_BUS_AUDIO_HUB] = { 0xa6c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+ [RST_USB_PHY2] = { 0xa78, BIT(30) },
+ [RST_USB_PHY3] = { 0xa7c, BIT(30) },
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_OHCI2] = { 0xa8c, BIT(18) },
+ [RST_BUS_OHCI3] = { 0xa8c, BIT(19) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_EHCI2] = { 0xa8c, BIT(22) },
+ [RST_BUS_EHCI3] = { 0xa8c, BIT(23) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+ [RST_BUS_KEYADC] = { 0xa9c, BIT(16) },
+
+ [RST_BUS_HDMI] = { 0xb1c, BIT(16) },
+ [RST_BUS_HDMI_SUB] = { 0xb1c, BIT(17) },
+ [RST_BUS_TCON_TOP] = { 0xb5c, BIT(16) },
+ [RST_BUS_TCON_TV0] = { 0xb9c, BIT(16) },
+ [RST_BUS_TCON_TV1] = { 0xb9c, BIT(17) },
+ [RST_BUS_TVE_TOP] = { 0xbbc, BIT(16) },
+ [RST_BUS_TVE0] = { 0xbbc, BIT(17) },
+ [RST_BUS_HDCP] = { 0xc4c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_h616_ccu_desc = {
+ .ccu_clks = sun50i_h616_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h616_ccu_clks),
+
+ .hw_clks = &sun50i_h616_hw_clks,
+
+ .resets = sun50i_h616_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h616_ccu_resets),
+};
+
+static const u32 pll_regs[] = {
+ SUN50I_H616_PLL_CPUX_REG,
+ SUN50I_H616_PLL_DDR0_REG,
+ SUN50I_H616_PLL_DDR1_REG,
+ SUN50I_H616_PLL_PERIPH0_REG,
+ SUN50I_H616_PLL_PERIPH1_REG,
+ SUN50I_H616_PLL_GPU_REG,
+ SUN50I_H616_PLL_VIDEO0_REG,
+ SUN50I_H616_PLL_VIDEO1_REG,
+ SUN50I_H616_PLL_VIDEO2_REG,
+ SUN50I_H616_PLL_VE_REG,
+ SUN50I_H616_PLL_DE_REG,
+ SUN50I_H616_PLL_AUDIO_REG,
+};
+
+static const u32 pll_video_regs[] = {
+ SUN50I_H616_PLL_VIDEO0_REG,
+ SUN50I_H616_PLL_VIDEO1_REG,
+ SUN50I_H616_PLL_VIDEO2_REG,
+};
+
+static const u32 usb2_clk_regs[] = {
+ SUN50I_H616_USB0_CLK_REG,
+ SUN50I_H616_USB1_CLK_REG,
+ SUN50I_H616_USB2_CLK_REG,
+ SUN50I_H616_USB3_CLK_REG,
+};
+
+static void __init sun50i_h616_ccu_setup(struct device_node *node)
+{
+ void __iomem *reg;
+ u32 val;
+ int i;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg)) {
+ pr_err("%pOF: Could not map clock registers\n", node);
+ return;
+ }
+
+ /* Enable the lock bits and the output enable bits on all PLLs */
+ for (i = 0; i < ARRAY_SIZE(pll_regs); i++) {
+ val = readl(reg + pll_regs[i]);
+ val |= BIT(29) | BIT(27);
+ writel(val, reg + pll_regs[i]);
+ }
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(pll_video_regs); i++) {
+ val = readl(reg + pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + pll_video_regs[i]);
+ }
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(usb2_clk_regs); i++) {
+ val = readl(reg + usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + usb2_clk_regs[i]);
+ }
+
+ /*
+ * Force the post-divider of pll-audio to 12 and the output divider
+ * of it to 2, so 24576000 and 22579200 rates can be set exactly.
+ */
+ val = readl(reg + SUN50I_H616_PLL_AUDIO_REG);
+ val &= ~(GENMASK(21, 16) | BIT(0));
+ writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG);
+
+ /*
+ * First clock parent (osc32K) is unusable for CEC. But since there
+ * is no good way to force parent switch (both run with same frequency),
+ * just set second clock parent here.
+ */
+ val = readl(reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+ val |= BIT(24);
+ writel(val, reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+
+ i = sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
+ if (i)
+ pr_err("%pOF: probing clocks fails: %d\n", node, i);
+}
+
+CLK_OF_DECLARE(sun50i_h616_ccu, "allwinner,sun50i-h616-ccu",
+ sun50i_h616_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.h b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
new file mode 100644
index 000000000000..dd671b413f22
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2020 Arm Ltd.
+ */
+
+#ifndef _CCU_SUN50I_H616_H_
+#define _CCU_SUN50I_H616_H_
+
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+#define CLK_PLL_DDR1 3
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 5
+#define CLK_PLL_PERIPH1 6
+#define CLK_PLL_PERIPH1_2X 7
+#define CLK_PLL_GPU 8
+#define CLK_PLL_VIDEO0 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_4X 12
+#define CLK_PLL_VIDEO2 13
+#define CLK_PLL_VIDEO2_4X 14
+#define CLK_PLL_VE 15
+#define CLK_PLL_DE 16
+#define CLK_PLL_AUDIO_HS 17
+#define CLK_PLL_AUDIO_1X 18
+#define CLK_PLL_AUDIO_2X 19
+#define CLK_PLL_AUDIO_4X 20
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 22
+#define CLK_CPUX_APB 23
+#define CLK_PSI_AHB1_AHB2 24
+#define CLK_AHB3 25
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 27
+#define CLK_MBUS 28
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_DRAM 49
+
+#define CLK_BUS_DRAM 56
+
+#define CLK_NUMBER (CLK_BUS_HDCP + 1)
+
+#endif /* _CCU_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..4fc08b0df2f3
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_H616_H_
+#define _DT_BINDINGS_CLK_SUN50I_H616_H_
+
+#define CLK_PLL_PERIPH0 4
+
+#define CLK_CPUX 21
+
+#define CLK_APB1 26
+
+#define CLK_DE 29
+#define CLK_BUS_DE 30
+#define CLK_DEINTERLACE 31
+#define CLK_BUS_DEINTERLACE 32
+#define CLK_G2D 33
+#define CLK_BUS_G2D 34
+#define CLK_GPU0 35
+#define CLK_BUS_GPU 36
+#define CLK_GPU1 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_HSTIMER 43
+#define CLK_AVS 44
+#define CLK_BUS_DBG 45
+#define CLK_BUS_PSI 46
+#define CLK_BUS_PWM 47
+#define CLK_BUS_IOMMU 48
+
+#define CLK_MBUS_DMA 50
+#define CLK_MBUS_VE 51
+#define CLK_MBUS_CE 52
+#define CLK_MBUS_TS 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_G2D 55
+
+#define CLK_NAND0 57
+#define CLK_NAND1 58
+#define CLK_BUS_NAND 59
+#define CLK_MMC0 60
+#define CLK_MMC1 61
+#define CLK_MMC2 62
+#define CLK_BUS_MMC0 63
+#define CLK_BUS_MMC1 64
+#define CLK_BUS_MMC2 65
+#define CLK_BUS_UART0 66
+#define CLK_BUS_UART1 67
+#define CLK_BUS_UART2 68
+#define CLK_BUS_UART3 69
+#define CLK_BUS_UART4 70
+#define CLK_BUS_UART5 71
+#define CLK_BUS_I2C0 72
+#define CLK_BUS_I2C1 73
+#define CLK_BUS_I2C2 74
+#define CLK_BUS_I2C3 75
+#define CLK_BUS_I2C4 76
+#define CLK_SPI0 77
+#define CLK_SPI1 78
+#define CLK_BUS_SPI0 79
+#define CLK_BUS_SPI1 80
+#define CLK_EMAC_25M 81
+#define CLK_BUS_EMAC0 82
+#define CLK_BUS_EMAC1 83
+#define CLK_TS 84
+#define CLK_BUS_TS 85
+#define CLK_BUS_THS 86
+#define CLK_SPDIF 87
+#define CLK_BUS_SPDIF 88
+#define CLK_DMIC 89
+#define CLK_BUS_DMIC 90
+#define CLK_AUDIO_CODEC_1X 91
+#define CLK_AUDIO_CODEC_4X 92
+#define CLK_BUS_AUDIO_CODEC 93
+#define CLK_AUDIO_HUB 94
+#define CLK_BUS_AUDIO_HUB 95
+#define CLK_USB_OHCI0 96
+#define CLK_USB_PHY0 97
+#define CLK_USB_OHCI1 98
+#define CLK_USB_PHY1 99
+#define CLK_USB_OHCI2 100
+#define CLK_USB_PHY2 101
+#define CLK_USB_OHCI3 102
+#define CLK_USB_PHY3 103
+#define CLK_BUS_OHCI0 104
+#define CLK_BUS_OHCI1 105
+#define CLK_BUS_OHCI2 106
+#define CLK_BUS_OHCI3 107
+#define CLK_BUS_EHCI0 108
+#define CLK_BUS_EHCI1 109
+#define CLK_BUS_EHCI2 110
+#define CLK_BUS_EHCI3 111
+#define CLK_BUS_OTG 112
+#define CLK_BUS_KEYADC 113
+#define CLK_HDMI 114
+#define CLK_HDMI_SLOW 115
+#define CLK_HDMI_CEC 116
+#define CLK_BUS_HDMI 117
+#define CLK_BUS_TCON_TOP 118
+#define CLK_TCON_TV0 119
+#define CLK_TCON_TV1 120
+#define CLK_BUS_TCON_TV0 121
+#define CLK_BUS_TCON_TV1 122
+#define CLK_TVE0 123
+#define CLK_BUS_TVE_TOP 124
+#define CLK_BUS_TVE0 125
+#define CLK_HDCP 126
+#define CLK_BUS_HDCP 127
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..cb6285a8d128
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_H616_H_
+#define _DT_BINDINGS_RESET_SUN50I_H616_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_DEINTERLACE 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_HSTIMER 7
+#define RST_BUS_DBG 8
+#define RST_BUS_PSI 9
+#define RST_BUS_PWM 10
+#define RST_BUS_IOMMU 11
+#define RST_BUS_DRAM 12
+#define RST_BUS_NAND 13
+#define RST_BUS_MMC0 14
+#define RST_BUS_MMC1 15
+#define RST_BUS_MMC2 16
+#define RST_BUS_UART0 17
+#define RST_BUS_UART1 18
+#define RST_BUS_UART2 19
+#define RST_BUS_UART3 20
+#define RST_BUS_UART4 21
+#define RST_BUS_UART5 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_I2C4 27
+#define RST_BUS_SPI0 28
+#define RST_BUS_SPI1 29
+#define RST_BUS_EMAC0 30
+#define RST_BUS_EMAC1 31
+#define RST_BUS_TS 32
+#define RST_BUS_THS 33
+#define RST_BUS_SPDIF 34
+#define RST_BUS_DMIC 35
+#define RST_BUS_AUDIO_CODEC 36
+#define RST_BUS_AUDIO_HUB 37
+#define RST_USB_PHY0 38
+#define RST_USB_PHY1 39
+#define RST_USB_PHY2 40
+#define RST_USB_PHY3 41
+#define RST_BUS_OHCI0 42
+#define RST_BUS_OHCI1 43
+#define RST_BUS_OHCI2 44
+#define RST_BUS_OHCI3 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_EHCI2 48
+#define RST_BUS_EHCI3 49
+#define RST_BUS_OTG 50
+#define RST_BUS_HDMI 51
+#define RST_BUS_HDMI_SUB 52
+#define RST_BUS_TCON_TOP 53
+#define RST_BUS_TCON_TV0 54
+#define RST_BUS_TCON_TV1 55
+#define RST_BUS_TVE_TOP 56
+#define RST_BUS_TVE0 57
+#define RST_BUS_HDCP 58
+#define RST_BUS_KEYADC 59
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_H616_H_ */
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 07/21] clk: sunxi-ng: Add support for the Allwinner H616 CCU
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel, linux-clk,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Philipp Zabel, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.
Derived from the H6 clock driver, and adjusted according to the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/clk/sunxi-ng/Kconfig | 5 +
drivers/clk/sunxi-ng/Makefile | 1 +
drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150 +++++++++++++++++++
drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
include/dt-bindings/reset/sun50i-h616-ccu.h | 70 ++
6 files changed, 1397 insertions(+)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index feeb8d2074ee..cd46d8853876 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -32,6 +32,11 @@ config SUN50I_H6_CCU
default ARM64 && ARCH_SUNXI
depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+config SUN50I_H616_CCU
+ bool "Support for the Allwinner H616 CCU"
+ default ARM64 && ARCH_SUNXI
+ depends on (ARM64 && ARCH_SUNXI) || COMPILE_TEST
+
config SUN50I_H6_R_CCU
bool "Support for the Allwinner H6 and H616 PRCM CCU"
default ARM64 && ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 3eb5cff40eac..96c324306d97 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -26,6 +26,7 @@ obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
obj-$(CONFIG_SUN50I_A100_CCU) += ccu-sun50i-a100.o
obj-$(CONFIG_SUN50I_A100_R_CCU) += ccu-sun50i-a100-r.o
obj-$(CONFIG_SUN50I_H6_CCU) += ccu-sun50i-h6.o
+obj-$(CONFIG_SUN50I_H616_CCU) += ccu-sun50i-h616.o
obj-$(CONFIG_SUN50I_H6_R_CCU) += ccu-sun50i-h6-r.o
obj-$(CONFIG_SUN4I_A10_CCU) += ccu-sun4i-a10.o
obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.c b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
new file mode 100644
index 000000000000..19db5636a80d
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.c
@@ -0,0 +1,1150 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 Arm Ltd.
+ * Based on the H6 CCU driver, which is:
+ * Copyright (c) 2017 Icenowy Zheng <icenowy@aosc.io>
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+
+#include "ccu-sun50i-h616.h"
+
+/*
+ * The CPU PLL is actually NP clock, with P being /1, /2 or /4. However
+ * P should only be used for output frequencies lower than 288 MHz.
+ *
+ * For now we can just model it as a multiplier clock, and force P to /1.
+ *
+ * The M factor is present in the register's description, but not in the
+ * frequency formula, and it's documented as "M is only used for backdoor
+ * testing", so it's not modelled and then force to 0.
+ */
+#define SUN50I_H616_PLL_CPUX_REG 0x000
+static struct ccu_mult pll_cpux_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .mult = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-cpux", "osc24M",
+ &ccu_mult_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/* Some PLLs are input * N / div1 / P. Model them as NKMP with no K */
+#define SUN50I_H616_PLL_DDR0_REG 0x010
+static struct ccu_nkmp pll_ddr0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x010,
+ .hw.init = CLK_HW_INIT("pll-ddr0", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_DDR1_REG 0x018
+static struct ccu_nkmp pll_ddr1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x018,
+ .hw.init = CLK_HW_INIT("pll-ddr1", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_PERIPH0_REG 0x020
+static struct ccu_nkmp pll_periph0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x020,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph0", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_PERIPH1_REG 0x028
+static struct ccu_nkmp pll_periph1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph1", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_GPU_REG 0x030
+static struct ccu_nkmp pll_gpu_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x030,
+ .hw.init = CLK_HW_INIT("pll-gpu", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * For Video PLLs, the output divider is described as "used for testing"
+ * in the user manual. So it's not modelled and forced to 0.
+ */
+#define SUN50I_H616_PLL_VIDEO0_REG 0x040
+static struct ccu_nm pll_video0_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x040,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video0", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VIDEO1_REG 0x048
+static struct ccu_nm pll_video1_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x048,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video1", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VIDEO2_REG 0x050
+static struct ccu_nm pll_video2_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .fixed_post_div = 4,
+ .min_rate = 288000000,
+ .max_rate = 2400000000UL,
+ .common = {
+ .reg = 0x050,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-video2", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_VE_REG 0x058
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x058,
+ .hw.init = CLK_HW_INIT("pll-ve", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+#define SUN50I_H616_PLL_DE_REG 0x060
+static struct ccu_nkmp pll_de_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .p = _SUNXI_CCU_DIV(0, 1), /* output divider */
+ .common = {
+ .reg = 0x060,
+ .hw.init = CLK_HW_INIT("pll-de", "osc24M",
+ &ccu_nkmp_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+/*
+ * TODO: Determine SDM settings for the audio PLL. The manual suggests
+ * PLL_FACTOR_N=16, PLL_POST_DIV_P=2, OUTPUT_DIV=2, pattern=0xe000c49b
+ * for 24.576 MHz, and PLL_FACTOR_N=22, PLL_POST_DIV_P=3, OUTPUT_DIV=2,
+ * pattern=0xe001288c for 22.5792 MHz.
+ * This clashes with our fixed PLL_POST_DIV_P.
+ */
+#define SUN50I_H616_PLL_AUDIO_REG 0x078
+static struct ccu_nm pll_audio_hs_clk = {
+ .enable = BIT(31),
+ .lock = BIT(28),
+ .n = _SUNXI_CCU_MULT_MIN(8, 8, 12),
+ .m = _SUNXI_CCU_DIV(1, 1), /* input divider */
+ .common = {
+ .reg = 0x078,
+ .hw.init = CLK_HW_INIT("pll-audio-hs", "osc24M",
+ &ccu_nm_ops,
+ CLK_SET_RATE_UNGATE),
+ },
+};
+
+static const char * const cpux_parents[] = { "osc24M", "osc32k",
+ "iosc", "pll-cpux", "pll-periph0" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+ 0x500, 24, 3, CLK_SET_RATE_PARENT | CLK_IS_CRITICAL);
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x500, 0, 2, 0);
+static SUNXI_CCU_M(cpux_apb_clk, "cpux-apb", "cpux", 0x500, 8, 2, 0);
+
+static const char * const psi_ahb1_ahb2_parents[] = { "osc24M", "osc32k",
+ "iosc", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(psi_ahb1_ahb2_clk, "psi-ahb1-ahb2",
+ psi_ahb1_ahb2_parents,
+ 0x510,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static const char * const ahb3_apb1_apb2_parents[] = { "osc24M", "osc32k",
+ "psi-ahb1-ahb2",
+ "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX(ahb3_clk, "ahb3", ahb3_apb1_apb2_parents, 0x51c,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", ahb3_apb1_apb2_parents, 0x520,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", ahb3_apb1_apb2_parents, 0x524,
+ 0, 2, /* M */
+ 8, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-ddr0", "pll-ddr1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x540,
+ 0, 3, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_IS_CRITICAL);
+
+static const char * const de_parents[] = { "pll-de", "pll-periph0-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents, 0x600,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "psi-ahb1-ahb2",
+ 0x60c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(deinterlace_clk, "deinterlace",
+ de_parents,
+ 0x620,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_deinterlace_clk, "bus-deinterlace", "psi-ahb1-ahb2",
+ 0x62c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(g2d_clk, "g2d", de_parents, 0x630,
+ 0, 4, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_g2d_clk, "bus-g2d", "psi-ahb1-ahb2",
+ 0x63c, BIT(0), 0);
+
+static const char * const gpu0_parents[] = { "pll-gpu", "gpu1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu0_clk, "gpu0", gpu0_parents, 0x670,
+ 0, 2, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_GATE(gpu1_clk, "gpu1", "pll-periph0-2x", 0x674,
+ 0, 2, /* M */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_gpu_clk, "bus-gpu", "psi-ahb1-ahb2",
+ 0x67c, BIT(0), 0);
+
+static const char * const ce_parents[] = { "osc24M", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ce_clk, "ce", ce_parents, 0x680,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 1, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ce_clk, "bus-ce", "psi-ahb1-ahb2",
+ 0x68c, BIT(0), 0);
+
+static const char * const ve_parents[] = { "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(ve_clk, "ve", ve_parents, 0x690,
+ 0, 3, /* M */
+ 24, 1, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_ve_clk, "bus-ve", "psi-ahb1-ahb2",
+ 0x69c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "psi-ahb1-ahb2",
+ 0x70c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_hstimer_clk, "bus-hstimer", "psi-ahb1-ahb2",
+ 0x73c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "osc24M", 0x740, BIT(31), 0);
+
+static SUNXI_CCU_GATE(bus_dbg_clk, "bus-dbg", "psi-ahb1-ahb2",
+ 0x78c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_psi_clk, "bus-psi", "psi-ahb1-ahb2",
+ 0x79c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_pwm_clk, "bus-pwm", "apb1", 0x7ac, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_iommu_clk, "bus-iommu", "apb1", 0x7bc, BIT(0), 0);
+
+static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1" };
+static struct ccu_div dram_clk = {
+ .div = _SUNXI_CCU_DIV(0, 2),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0x800,
+ .hw.init = CLK_HW_INIT_PARENTS("dram",
+ dram_parents,
+ &ccu_div_ops,
+ CLK_IS_CRITICAL),
+ },
+};
+
+static SUNXI_CCU_GATE(mbus_dma_clk, "mbus-dma", "mbus",
+ 0x804, BIT(0), 0);
+static SUNXI_CCU_GATE(mbus_ve_clk, "mbus-ve", "mbus",
+ 0x804, BIT(1), 0);
+static SUNXI_CCU_GATE(mbus_ce_clk, "mbus-ce", "mbus",
+ 0x804, BIT(2), 0);
+static SUNXI_CCU_GATE(mbus_ts_clk, "mbus-ts", "mbus",
+ 0x804, BIT(3), 0);
+static SUNXI_CCU_GATE(mbus_nand_clk, "mbus-nand", "mbus",
+ 0x804, BIT(5), 0);
+static SUNXI_CCU_GATE(mbus_g2d_clk, "mbus-g2d", "mbus",
+ 0x804, BIT(10), 0);
+
+static SUNXI_CCU_GATE(bus_dram_clk, "bus-dram", "psi-ahb1-ahb2",
+ 0x80c, BIT(0), CLK_IS_CRITICAL);
+
+static const char * const nand_spi_parents[] = { "osc24M", "pll-periph0",
+ "pll-periph1", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand0_clk, "nand0", nand_spi_parents, 0x810,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand1_clk, "nand1", nand_spi_parents, 0x814,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb3", 0x82c, BIT(0), 0);
+
+static const char * const mmc_parents[] = { "osc24M", "pll-periph0-2x",
+ "pll-periph1-2x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc0_clk, "mmc0", mmc_parents, 0x830,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc1_clk, "mmc1", mmc_parents, 0x834,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mmc_parents, 0x838,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 2, /* post-div */
+ 0);
+
+static SUNXI_CCU_GATE(bus_mmc0_clk, "bus-mmc0", "ahb3", 0x84c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_mmc1_clk, "bus-mmc1", "ahb3", 0x84c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_mmc2_clk, "bus-mmc2", "ahb3", 0x84c, BIT(2), 0);
+
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2", 0x90c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2", 0x90c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2", 0x90c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2", 0x90c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2", 0x90c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2", 0x90c, BIT(5), 0);
+
+static SUNXI_CCU_GATE(bus_i2c0_clk, "bus-i2c0", "apb2", 0x91c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_i2c1_clk, "bus-i2c1", "apb2", 0x91c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_i2c2_clk, "bus-i2c2", "apb2", 0x91c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_i2c3_clk, "bus-i2c3", "apb2", 0x91c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_i2c4_clk, "bus-i2c4", "apb2", 0x91c, BIT(4), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", nand_spi_parents, 0x940,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", nand_spi_parents, 0x944,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 3, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb3", 0x96c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb3", 0x96c, BIT(1), 0);
+
+static SUNXI_CCU_GATE(emac_25m_clk, "emac-25m", "ahb3", 0x970,
+ BIT(31) | BIT(30), 0);
+
+static SUNXI_CCU_GATE(bus_emac0_clk, "bus-emac0", "ahb3", 0x97c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_emac1_clk, "bus-emac1", "ahb3", 0x97c, BIT(1), 0);
+
+static const char * const ts_parents[] = { "osc24M", "pll-periph0" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", ts_parents, 0x9b0,
+ 0, 4, /* M */
+ 8, 2, /* N */
+ 24, 1, /* mux */
+ BIT(31),/* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_ts_clk, "bus-ts", "ahb3", 0x9bc, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1", 0x9fc, BIT(0), 0);
+
+static const char * const audio_parents[] = { "pll-audio-1x", "pll-audio-2x",
+ "pll-audio-4x", "pll-audio-hs" };
+static struct ccu_div spdif_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa20,
+ .hw.init = CLK_HW_INIT_PARENTS("spdif",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1", 0xa2c, BIT(0), 0);
+
+static struct ccu_div dmic_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa40,
+ .hw.init = CLK_HW_INIT_PARENTS("dmic",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1", 0xa4c, BIT(0), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_1x_clk, "audio-codec-1x",
+ audio_parents, 0xa50,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(audio_codec_4x_clk, "audio-codec-4x",
+ audio_parents, 0xa54,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_audio_codec_clk, "bus-audio-codec", "apb1", 0xa5c,
+ BIT(0), 0);
+
+static struct ccu_div audio_hub_clk = {
+ .enable = BIT(31),
+ .div = _SUNXI_CCU_DIV_FLAGS(8, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = _SUNXI_CCU_MUX(24, 2),
+ .common = {
+ .reg = 0xa60,
+ .hw.init = CLK_HW_INIT_PARENTS("audio-hub",
+ audio_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_audio_hub_clk, "bus-audio-hub", "apb1", 0xa6c, BIT(0), 0);
+
+/*
+ * There are OHCI 12M clock source selection bits for the four USB 2.0 ports.
+ * We will force them to 0 (12M divided from 48M).
+ */
+#define SUN50I_H616_USB0_CLK_REG 0xa70
+#define SUN50I_H616_USB1_CLK_REG 0xa74
+#define SUN50I_H616_USB2_CLK_REG 0xa78
+#define SUN50I_H616_USB3_CLK_REG 0xa7c
+
+static SUNXI_CCU_GATE(usb_ohci0_clk, "usb-ohci0", "osc12M", 0xa70, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "osc24M", 0xa70, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci1_clk, "usb-ohci1", "osc12M", 0xa74, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "osc24M", 0xa74, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci2_clk, "usb-ohci2", "osc12M", 0xa78, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy2_clk, "usb-phy2", "osc24M", 0xa78, BIT(29), 0);
+
+static SUNXI_CCU_GATE(usb_ohci3_clk, "usb-ohci3", "osc12M", 0xa7c, BIT(31), 0);
+static SUNXI_CCU_GATE(usb_phy3_clk, "usb-phy3", "osc24M", 0xa7c, BIT(29), 0);
+
+static SUNXI_CCU_GATE(bus_ohci0_clk, "bus-ohci0", "ahb3", 0xa8c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_ohci1_clk, "bus-ohci1", "ahb3", 0xa8c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_ohci2_clk, "bus-ohci2", "ahb3", 0xa8c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_ohci3_clk, "bus-ohci3", "ahb3", 0xa8c, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_ehci0_clk, "bus-ehci0", "ahb3", 0xa8c, BIT(4), 0);
+static SUNXI_CCU_GATE(bus_ehci1_clk, "bus-ehci1", "ahb3", 0xa8c, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_ehci2_clk, "bus-ehci2", "ahb3", 0xa8c, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_ehci3_clk, "bus-ehci3", "ahb3", 0xa8c, BIT(7), 0);
+static SUNXI_CCU_GATE(bus_otg_clk, "bus-otg", "ahb3", 0xa8c, BIT(8), 0);
+
+static SUNXI_CCU_GATE(bus_keyadc_clk, "bus-keyadc", "apb1", 0xa9c, BIT(0), 0);
+
+static const char * const hdmi_parents[] = { "pll-video0", "pll-video0-4x",
+ "pll-video2", "pll-video2-4x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdmi_clk, "hdmi", hdmi_parents, 0xb00,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(hdmi_slow_clk, "hdmi-slow", "osc24M", 0xb04, BIT(31), 0);
+
+static const char * const hdmi_cec_parents[] = { "osc32k", "pll-periph0-2x" };
+static const struct ccu_mux_fixed_prediv hdmi_cec_predivs[] = {
+ { .index = 1, .div = 36621 },
+};
+
+#define SUN50I_H616_HDMI_CEC_CLK_REG 0xb10
+static struct ccu_mux hdmi_cec_clk = {
+ .enable = BIT(31),
+
+ .mux = {
+ .shift = 24,
+ .width = 2,
+
+ .fixed_predivs = hdmi_cec_predivs,
+ .n_predivs = ARRAY_SIZE(hdmi_cec_predivs),
+ },
+
+ .common = {
+ .reg = 0xb10,
+ .features = CCU_FEATURE_VARIABLE_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("hdmi-cec",
+ hdmi_cec_parents,
+ &ccu_mux_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(bus_hdmi_clk, "bus-hdmi", "ahb3", 0xb1c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(bus_tcon_top_clk, "bus-tcon-top", "ahb3",
+ 0xb5c, BIT(0), 0);
+
+static const char * const tcon_tv_parents[] = { "pll-video0",
+ "pll-video0-4x",
+ "pll-video1",
+ "pll-video1-4x" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv0_clk, "tcon-tv0",
+ tcon_tv_parents, 0xb80,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+static SUNXI_CCU_MP_WITH_MUX_GATE(tcon_tv1_clk, "tcon-tv1",
+ tcon_tv_parents, 0xb84,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tcon_tv0_clk, "bus-tcon-tv0", "ahb3",
+ 0xb9c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tcon_tv1_clk, "bus-tcon-tv1", "ahb3",
+ 0xb9c, BIT(1), 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(tve0_clk, "tve0",
+ tcon_tv_parents, 0xbb0,
+ 0, 4, /* M */
+ 8, 2, /* P */
+ 24, 3, /* mux */
+ BIT(31), /* gate */
+ CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(bus_tve_top_clk, "bus-tve-top", "ahb3",
+ 0xbbc, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_tve0_clk, "bus-tve0", "ahb3",
+ 0xbbc, BIT(1), 0);
+
+static const char * const hdcp_parents[] = { "pll-periph0", "pll-periph1" };
+static SUNXI_CCU_M_WITH_MUX_GATE(hdcp_clk, "hdcp", hdcp_parents, 0xc40,
+ 0, 4, /* M */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_GATE(bus_hdcp_clk, "bus-hdcp", "ahb3", 0xc4c, BIT(0), 0);
+
+/* Fixed factor clocks */
+static CLK_FIXED_FACTOR_FW_NAME(osc12M_clk, "osc12M", "hosc", 2, 1, 0);
+
+static const struct clk_hw *clk_parent_pll_audio[] = {
+ &pll_audio_hs_clk.common.hw
+};
+
+/*
+ * The divider of pll-audio is fixed to 24 for now, so 24576000 and 22579200
+ * rates can be set exactly in conjunction with sigma-delta modulation.
+ */
+static CLK_FIXED_FACTOR_HWS(pll_audio_1x_clk, "pll-audio-1x",
+ clk_parent_pll_audio,
+ 96, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_2x_clk, "pll-audio-2x",
+ clk_parent_pll_audio,
+ 48, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HWS(pll_audio_4x_clk, "pll-audio-4x",
+ clk_parent_pll_audio,
+ 24, 1, CLK_SET_RATE_PARENT);
+
+static const struct clk_hw *pll_periph0_parents[] = {
+ &pll_periph0_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph0_2x_clk, "pll-periph0-2x",
+ pll_periph0_parents,
+ 1, 2, 0);
+
+static const struct clk_hw *pll_periph1_parents[] = {
+ &pll_periph1_clk.common.hw
+};
+
+static CLK_FIXED_FACTOR_HWS(pll_periph1_2x_clk, "pll-periph1-2x",
+ pll_periph1_parents,
+ 1, 2, 0);
+
+static CLK_FIXED_FACTOR_HW(pll_video0_4x_clk, "pll-video0-4x",
+ &pll_video0_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video1_4x_clk, "pll-video1-4x",
+ &pll_video1_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR_HW(pll_video2_4x_clk, "pll-video2-4x",
+ &pll_video2_clk.common.hw,
+ 1, 4, CLK_SET_RATE_PARENT);
+
+static struct ccu_common *sun50i_h616_ccu_clks[] = {
+ &pll_cpux_clk.common,
+ &pll_ddr0_clk.common,
+ &pll_ddr1_clk.common,
+ &pll_periph0_clk.common,
+ &pll_periph1_clk.common,
+ &pll_gpu_clk.common,
+ &pll_video0_clk.common,
+ &pll_video1_clk.common,
+ &pll_video2_clk.common,
+ &pll_ve_clk.common,
+ &pll_de_clk.common,
+ &pll_audio_hs_clk.common,
+ &cpux_clk.common,
+ &axi_clk.common,
+ &cpux_apb_clk.common,
+ &psi_ahb1_ahb2_clk.common,
+ &ahb3_clk.common,
+ &apb1_clk.common,
+ &apb2_clk.common,
+ &mbus_clk.common,
+ &de_clk.common,
+ &bus_de_clk.common,
+ &deinterlace_clk.common,
+ &bus_deinterlace_clk.common,
+ &g2d_clk.common,
+ &bus_g2d_clk.common,
+ &gpu0_clk.common,
+ &bus_gpu_clk.common,
+ &gpu1_clk.common,
+ &ce_clk.common,
+ &bus_ce_clk.common,
+ &ve_clk.common,
+ &bus_ve_clk.common,
+ &bus_dma_clk.common,
+ &bus_hstimer_clk.common,
+ &avs_clk.common,
+ &bus_dbg_clk.common,
+ &bus_psi_clk.common,
+ &bus_pwm_clk.common,
+ &bus_iommu_clk.common,
+ &dram_clk.common,
+ &mbus_dma_clk.common,
+ &mbus_ve_clk.common,
+ &mbus_ce_clk.common,
+ &mbus_ts_clk.common,
+ &mbus_nand_clk.common,
+ &mbus_g2d_clk.common,
+ &bus_dram_clk.common,
+ &nand0_clk.common,
+ &nand1_clk.common,
+ &bus_nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &bus_mmc0_clk.common,
+ &bus_mmc1_clk.common,
+ &bus_mmc2_clk.common,
+ &bus_uart0_clk.common,
+ &bus_uart1_clk.common,
+ &bus_uart2_clk.common,
+ &bus_uart3_clk.common,
+ &bus_uart4_clk.common,
+ &bus_uart5_clk.common,
+ &bus_i2c0_clk.common,
+ &bus_i2c1_clk.common,
+ &bus_i2c2_clk.common,
+ &bus_i2c3_clk.common,
+ &bus_i2c4_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &bus_spi0_clk.common,
+ &bus_spi1_clk.common,
+ &emac_25m_clk.common,
+ &bus_emac0_clk.common,
+ &bus_emac1_clk.common,
+ &ts_clk.common,
+ &bus_ts_clk.common,
+ &bus_ths_clk.common,
+ &spdif_clk.common,
+ &bus_spdif_clk.common,
+ &dmic_clk.common,
+ &bus_dmic_clk.common,
+ &audio_codec_1x_clk.common,
+ &audio_codec_4x_clk.common,
+ &bus_audio_codec_clk.common,
+ &audio_hub_clk.common,
+ &bus_audio_hub_clk.common,
+ &usb_ohci0_clk.common,
+ &usb_phy0_clk.common,
+ &usb_ohci1_clk.common,
+ &usb_phy1_clk.common,
+ &usb_ohci2_clk.common,
+ &usb_phy2_clk.common,
+ &usb_ohci3_clk.common,
+ &usb_phy3_clk.common,
+ &bus_ohci0_clk.common,
+ &bus_ohci1_clk.common,
+ &bus_ohci2_clk.common,
+ &bus_ohci3_clk.common,
+ &bus_ehci0_clk.common,
+ &bus_ehci1_clk.common,
+ &bus_ehci2_clk.common,
+ &bus_ehci3_clk.common,
+ &bus_otg_clk.common,
+ &bus_keyadc_clk.common,
+ &hdmi_clk.common,
+ &hdmi_slow_clk.common,
+ &hdmi_cec_clk.common,
+ &bus_hdmi_clk.common,
+ &bus_tcon_top_clk.common,
+ &tcon_tv0_clk.common,
+ &tcon_tv1_clk.common,
+ &bus_tcon_tv0_clk.common,
+ &bus_tcon_tv1_clk.common,
+ &tve0_clk.common,
+ &bus_tve_top_clk.common,
+ &bus_tve0_clk.common,
+ &hdcp_clk.common,
+ &bus_hdcp_clk.common,
+};
+
+static struct clk_hw_onecell_data sun50i_h616_hw_clks = {
+ .hws = {
+ [CLK_OSC12M] = &osc12M_clk.hw,
+ [CLK_PLL_CPUX] = &pll_cpux_clk.common.hw,
+ [CLK_PLL_DDR0] = &pll_ddr0_clk.common.hw,
+ [CLK_PLL_DDR1] = &pll_ddr1_clk.common.hw,
+ [CLK_PLL_PERIPH0] = &pll_periph0_clk.common.hw,
+ [CLK_PLL_PERIPH0_2X] = &pll_periph0_2x_clk.hw,
+ [CLK_PLL_PERIPH1] = &pll_periph1_clk.common.hw,
+ [CLK_PLL_PERIPH1_2X] = &pll_periph1_2x_clk.hw,
+ [CLK_PLL_GPU] = &pll_gpu_clk.common.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_4X] = &pll_video0_4x_clk.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_4X] = &pll_video1_4x_clk.hw,
+ [CLK_PLL_VIDEO2] = &pll_video2_clk.common.hw,
+ [CLK_PLL_VIDEO2_4X] = &pll_video2_4x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DE] = &pll_de_clk.common.hw,
+ [CLK_PLL_AUDIO_HS] = &pll_audio_hs_clk.common.hw,
+ [CLK_PLL_AUDIO_1X] = &pll_audio_1x_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_CPUX] = &cpux_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_CPUX_APB] = &cpux_apb_clk.common.hw,
+ [CLK_PSI_AHB1_AHB2] = &psi_ahb1_ahb2_clk.common.hw,
+ [CLK_AHB3] = &ahb3_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_APB2] = &apb2_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_DE] = &de_clk.common.hw,
+ [CLK_BUS_DE] = &bus_de_clk.common.hw,
+ [CLK_DEINTERLACE] = &deinterlace_clk.common.hw,
+ [CLK_BUS_DEINTERLACE] = &bus_deinterlace_clk.common.hw,
+ [CLK_G2D] = &g2d_clk.common.hw,
+ [CLK_BUS_G2D] = &bus_g2d_clk.common.hw,
+ [CLK_GPU0] = &gpu0_clk.common.hw,
+ [CLK_BUS_GPU] = &bus_gpu_clk.common.hw,
+ [CLK_GPU1] = &gpu1_clk.common.hw,
+ [CLK_CE] = &ce_clk.common.hw,
+ [CLK_BUS_CE] = &bus_ce_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_BUS_VE] = &bus_ve_clk.common.hw,
+ [CLK_BUS_DMA] = &bus_dma_clk.common.hw,
+ [CLK_BUS_HSTIMER] = &bus_hstimer_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_BUS_DBG] = &bus_dbg_clk.common.hw,
+ [CLK_BUS_PSI] = &bus_psi_clk.common.hw,
+ [CLK_BUS_PWM] = &bus_pwm_clk.common.hw,
+ [CLK_BUS_IOMMU] = &bus_iommu_clk.common.hw,
+ [CLK_DRAM] = &dram_clk.common.hw,
+ [CLK_MBUS_DMA] = &mbus_dma_clk.common.hw,
+ [CLK_MBUS_VE] = &mbus_ve_clk.common.hw,
+ [CLK_MBUS_CE] = &mbus_ce_clk.common.hw,
+ [CLK_MBUS_TS] = &mbus_ts_clk.common.hw,
+ [CLK_MBUS_NAND] = &mbus_nand_clk.common.hw,
+ [CLK_MBUS_G2D] = &mbus_g2d_clk.common.hw,
+ [CLK_BUS_DRAM] = &bus_dram_clk.common.hw,
+ [CLK_NAND0] = &nand0_clk.common.hw,
+ [CLK_NAND1] = &nand1_clk.common.hw,
+ [CLK_BUS_NAND] = &bus_nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_BUS_MMC0] = &bus_mmc0_clk.common.hw,
+ [CLK_BUS_MMC1] = &bus_mmc1_clk.common.hw,
+ [CLK_BUS_MMC2] = &bus_mmc2_clk.common.hw,
+ [CLK_BUS_UART0] = &bus_uart0_clk.common.hw,
+ [CLK_BUS_UART1] = &bus_uart1_clk.common.hw,
+ [CLK_BUS_UART2] = &bus_uart2_clk.common.hw,
+ [CLK_BUS_UART3] = &bus_uart3_clk.common.hw,
+ [CLK_BUS_UART4] = &bus_uart4_clk.common.hw,
+ [CLK_BUS_UART5] = &bus_uart5_clk.common.hw,
+ [CLK_BUS_I2C0] = &bus_i2c0_clk.common.hw,
+ [CLK_BUS_I2C1] = &bus_i2c1_clk.common.hw,
+ [CLK_BUS_I2C2] = &bus_i2c2_clk.common.hw,
+ [CLK_BUS_I2C3] = &bus_i2c3_clk.common.hw,
+ [CLK_BUS_I2C4] = &bus_i2c4_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_BUS_SPI0] = &bus_spi0_clk.common.hw,
+ [CLK_BUS_SPI1] = &bus_spi1_clk.common.hw,
+ [CLK_EMAC_25M] = &emac_25m_clk.common.hw,
+ [CLK_BUS_EMAC0] = &bus_emac0_clk.common.hw,
+ [CLK_BUS_EMAC1] = &bus_emac1_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_BUS_TS] = &bus_ts_clk.common.hw,
+ [CLK_BUS_THS] = &bus_ths_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_BUS_SPDIF] = &bus_spdif_clk.common.hw,
+ [CLK_DMIC] = &dmic_clk.common.hw,
+ [CLK_BUS_DMIC] = &bus_dmic_clk.common.hw,
+ [CLK_AUDIO_CODEC_1X] = &audio_codec_1x_clk.common.hw,
+ [CLK_AUDIO_CODEC_4X] = &audio_codec_4x_clk.common.hw,
+ [CLK_BUS_AUDIO_CODEC] = &bus_audio_codec_clk.common.hw,
+ [CLK_AUDIO_HUB] = &audio_hub_clk.common.hw,
+ [CLK_BUS_AUDIO_HUB] = &bus_audio_hub_clk.common.hw,
+ [CLK_USB_OHCI0] = &usb_ohci0_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_OHCI1] = &usb_ohci1_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_USB_OHCI2] = &usb_ohci2_clk.common.hw,
+ [CLK_USB_PHY2] = &usb_phy2_clk.common.hw,
+ [CLK_USB_OHCI3] = &usb_ohci3_clk.common.hw,
+ [CLK_USB_PHY3] = &usb_phy3_clk.common.hw,
+ [CLK_BUS_OHCI0] = &bus_ohci0_clk.common.hw,
+ [CLK_BUS_OHCI1] = &bus_ohci1_clk.common.hw,
+ [CLK_BUS_OHCI2] = &bus_ohci2_clk.common.hw,
+ [CLK_BUS_OHCI3] = &bus_ohci3_clk.common.hw,
+ [CLK_BUS_EHCI0] = &bus_ehci0_clk.common.hw,
+ [CLK_BUS_EHCI1] = &bus_ehci1_clk.common.hw,
+ [CLK_BUS_EHCI2] = &bus_ehci2_clk.common.hw,
+ [CLK_BUS_EHCI3] = &bus_ehci3_clk.common.hw,
+ [CLK_BUS_OTG] = &bus_otg_clk.common.hw,
+ [CLK_BUS_KEYADC] = &bus_keyadc_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_HDMI_SLOW] = &hdmi_slow_clk.common.hw,
+ [CLK_HDMI_CEC] = &hdmi_cec_clk.common.hw,
+ [CLK_BUS_HDMI] = &bus_hdmi_clk.common.hw,
+ [CLK_BUS_TCON_TOP] = &bus_tcon_top_clk.common.hw,
+ [CLK_TCON_TV0] = &tcon_tv0_clk.common.hw,
+ [CLK_TCON_TV1] = &tcon_tv1_clk.common.hw,
+ [CLK_BUS_TCON_TV0] = &bus_tcon_tv0_clk.common.hw,
+ [CLK_BUS_TCON_TV1] = &bus_tcon_tv1_clk.common.hw,
+ [CLK_TVE0] = &tve0_clk.common.hw,
+ [CLK_BUS_TVE_TOP] = &bus_tve_top_clk.common.hw,
+ [CLK_BUS_TVE0] = &bus_tve0_clk.common.hw,
+ [CLK_HDCP] = &hdcp_clk.common.hw,
+ [CLK_BUS_HDCP] = &bus_hdcp_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun50i_h616_ccu_resets[] = {
+ [RST_MBUS] = { 0x540, BIT(30) },
+
+ [RST_BUS_DE] = { 0x60c, BIT(16) },
+ [RST_BUS_DEINTERLACE] = { 0x62c, BIT(16) },
+ [RST_BUS_GPU] = { 0x67c, BIT(16) },
+ [RST_BUS_CE] = { 0x68c, BIT(16) },
+ [RST_BUS_VE] = { 0x69c, BIT(16) },
+ [RST_BUS_DMA] = { 0x70c, BIT(16) },
+ [RST_BUS_HSTIMER] = { 0x73c, BIT(16) },
+ [RST_BUS_DBG] = { 0x78c, BIT(16) },
+ [RST_BUS_PSI] = { 0x79c, BIT(16) },
+ [RST_BUS_PWM] = { 0x7ac, BIT(16) },
+ [RST_BUS_IOMMU] = { 0x7bc, BIT(16) },
+ [RST_BUS_DRAM] = { 0x80c, BIT(16) },
+ [RST_BUS_NAND] = { 0x82c, BIT(16) },
+ [RST_BUS_MMC0] = { 0x84c, BIT(16) },
+ [RST_BUS_MMC1] = { 0x84c, BIT(17) },
+ [RST_BUS_MMC2] = { 0x84c, BIT(18) },
+ [RST_BUS_UART0] = { 0x90c, BIT(16) },
+ [RST_BUS_UART1] = { 0x90c, BIT(17) },
+ [RST_BUS_UART2] = { 0x90c, BIT(18) },
+ [RST_BUS_UART3] = { 0x90c, BIT(19) },
+ [RST_BUS_UART4] = { 0x90c, BIT(20) },
+ [RST_BUS_UART5] = { 0x90c, BIT(21) },
+ [RST_BUS_I2C0] = { 0x91c, BIT(16) },
+ [RST_BUS_I2C1] = { 0x91c, BIT(17) },
+ [RST_BUS_I2C2] = { 0x91c, BIT(18) },
+ [RST_BUS_I2C3] = { 0x91c, BIT(19) },
+ [RST_BUS_I2C4] = { 0x91c, BIT(20) },
+ [RST_BUS_SPI0] = { 0x96c, BIT(16) },
+ [RST_BUS_SPI1] = { 0x96c, BIT(17) },
+ [RST_BUS_EMAC0] = { 0x97c, BIT(16) },
+ [RST_BUS_EMAC1] = { 0x97c, BIT(17) },
+ [RST_BUS_TS] = { 0x9bc, BIT(16) },
+ [RST_BUS_THS] = { 0x9fc, BIT(16) },
+ [RST_BUS_SPDIF] = { 0xa2c, BIT(16) },
+ [RST_BUS_DMIC] = { 0xa4c, BIT(16) },
+ [RST_BUS_AUDIO_CODEC] = { 0xa5c, BIT(16) },
+ [RST_BUS_AUDIO_HUB] = { 0xa6c, BIT(16) },
+
+ [RST_USB_PHY0] = { 0xa70, BIT(30) },
+ [RST_USB_PHY1] = { 0xa74, BIT(30) },
+ [RST_USB_PHY2] = { 0xa78, BIT(30) },
+ [RST_USB_PHY3] = { 0xa7c, BIT(30) },
+ [RST_BUS_OHCI0] = { 0xa8c, BIT(16) },
+ [RST_BUS_OHCI1] = { 0xa8c, BIT(17) },
+ [RST_BUS_OHCI2] = { 0xa8c, BIT(18) },
+ [RST_BUS_OHCI3] = { 0xa8c, BIT(19) },
+ [RST_BUS_EHCI0] = { 0xa8c, BIT(20) },
+ [RST_BUS_EHCI1] = { 0xa8c, BIT(21) },
+ [RST_BUS_EHCI2] = { 0xa8c, BIT(22) },
+ [RST_BUS_EHCI3] = { 0xa8c, BIT(23) },
+ [RST_BUS_OTG] = { 0xa8c, BIT(24) },
+ [RST_BUS_KEYADC] = { 0xa9c, BIT(16) },
+
+ [RST_BUS_HDMI] = { 0xb1c, BIT(16) },
+ [RST_BUS_HDMI_SUB] = { 0xb1c, BIT(17) },
+ [RST_BUS_TCON_TOP] = { 0xb5c, BIT(16) },
+ [RST_BUS_TCON_TV0] = { 0xb9c, BIT(16) },
+ [RST_BUS_TCON_TV1] = { 0xb9c, BIT(17) },
+ [RST_BUS_TVE_TOP] = { 0xbbc, BIT(16) },
+ [RST_BUS_TVE0] = { 0xbbc, BIT(17) },
+ [RST_BUS_HDCP] = { 0xc4c, BIT(16) },
+};
+
+static const struct sunxi_ccu_desc sun50i_h616_ccu_desc = {
+ .ccu_clks = sun50i_h616_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun50i_h616_ccu_clks),
+
+ .hw_clks = &sun50i_h616_hw_clks,
+
+ .resets = sun50i_h616_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun50i_h616_ccu_resets),
+};
+
+static const u32 pll_regs[] = {
+ SUN50I_H616_PLL_CPUX_REG,
+ SUN50I_H616_PLL_DDR0_REG,
+ SUN50I_H616_PLL_DDR1_REG,
+ SUN50I_H616_PLL_PERIPH0_REG,
+ SUN50I_H616_PLL_PERIPH1_REG,
+ SUN50I_H616_PLL_GPU_REG,
+ SUN50I_H616_PLL_VIDEO0_REG,
+ SUN50I_H616_PLL_VIDEO1_REG,
+ SUN50I_H616_PLL_VIDEO2_REG,
+ SUN50I_H616_PLL_VE_REG,
+ SUN50I_H616_PLL_DE_REG,
+ SUN50I_H616_PLL_AUDIO_REG,
+};
+
+static const u32 pll_video_regs[] = {
+ SUN50I_H616_PLL_VIDEO0_REG,
+ SUN50I_H616_PLL_VIDEO1_REG,
+ SUN50I_H616_PLL_VIDEO2_REG,
+};
+
+static const u32 usb2_clk_regs[] = {
+ SUN50I_H616_USB0_CLK_REG,
+ SUN50I_H616_USB1_CLK_REG,
+ SUN50I_H616_USB2_CLK_REG,
+ SUN50I_H616_USB3_CLK_REG,
+};
+
+static void __init sun50i_h616_ccu_setup(struct device_node *node)
+{
+ void __iomem *reg;
+ u32 val;
+ int i;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg)) {
+ pr_err("%pOF: Could not map clock registers\n", node);
+ return;
+ }
+
+ /* Enable the lock bits and the output enable bits on all PLLs */
+ for (i = 0; i < ARRAY_SIZE(pll_regs); i++) {
+ val = readl(reg + pll_regs[i]);
+ val |= BIT(29) | BIT(27);
+ writel(val, reg + pll_regs[i]);
+ }
+
+ /*
+ * Force the output divider of video PLLs to 0.
+ *
+ * See the comment before pll-video0 definition for the reason.
+ */
+ for (i = 0; i < ARRAY_SIZE(pll_video_regs); i++) {
+ val = readl(reg + pll_video_regs[i]);
+ val &= ~BIT(0);
+ writel(val, reg + pll_video_regs[i]);
+ }
+
+ /*
+ * Force OHCI 12M clock sources to 00 (12MHz divided from 48MHz)
+ *
+ * This clock mux is still mysterious, and the code just enforces
+ * it to have a valid clock parent.
+ */
+ for (i = 0; i < ARRAY_SIZE(usb2_clk_regs); i++) {
+ val = readl(reg + usb2_clk_regs[i]);
+ val &= ~GENMASK(25, 24);
+ writel(val, reg + usb2_clk_regs[i]);
+ }
+
+ /*
+ * Force the post-divider of pll-audio to 12 and the output divider
+ * of it to 2, so 24576000 and 22579200 rates can be set exactly.
+ */
+ val = readl(reg + SUN50I_H616_PLL_AUDIO_REG);
+ val &= ~(GENMASK(21, 16) | BIT(0));
+ writel(val | (11 << 16) | BIT(0), reg + SUN50I_H616_PLL_AUDIO_REG);
+
+ /*
+ * First clock parent (osc32K) is unusable for CEC. But since there
+ * is no good way to force parent switch (both run with same frequency),
+ * just set second clock parent here.
+ */
+ val = readl(reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+ val |= BIT(24);
+ writel(val, reg + SUN50I_H616_HDMI_CEC_CLK_REG);
+
+ i = sunxi_ccu_probe(node, reg, &sun50i_h616_ccu_desc);
+ if (i)
+ pr_err("%pOF: probing clocks fails: %d\n", node, i);
+}
+
+CLK_OF_DECLARE(sun50i_h616_ccu, "allwinner,sun50i-h616-ccu",
+ sun50i_h616_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun50i-h616.h b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
new file mode 100644
index 000000000000..dd671b413f22
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun50i-h616.h
@@ -0,0 +1,56 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright 2020 Arm Ltd.
+ */
+
+#ifndef _CCU_SUN50I_H616_H_
+#define _CCU_SUN50I_H616_H_
+
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+
+#define CLK_OSC12M 0
+#define CLK_PLL_CPUX 1
+#define CLK_PLL_DDR0 2
+#define CLK_PLL_DDR1 3
+
+/* PLL_PERIPH0 exported for PRCM */
+
+#define CLK_PLL_PERIPH0_2X 5
+#define CLK_PLL_PERIPH1 6
+#define CLK_PLL_PERIPH1_2X 7
+#define CLK_PLL_GPU 8
+#define CLK_PLL_VIDEO0 9
+#define CLK_PLL_VIDEO0_4X 10
+#define CLK_PLL_VIDEO1 11
+#define CLK_PLL_VIDEO1_4X 12
+#define CLK_PLL_VIDEO2 13
+#define CLK_PLL_VIDEO2_4X 14
+#define CLK_PLL_VE 15
+#define CLK_PLL_DE 16
+#define CLK_PLL_AUDIO_HS 17
+#define CLK_PLL_AUDIO_1X 18
+#define CLK_PLL_AUDIO_2X 19
+#define CLK_PLL_AUDIO_4X 20
+
+/* CPUX clock exported for DVFS */
+
+#define CLK_AXI 22
+#define CLK_CPUX_APB 23
+#define CLK_PSI_AHB1_AHB2 24
+#define CLK_AHB3 25
+
+/* APB1 clock exported for PIO */
+
+#define CLK_APB2 27
+#define CLK_MBUS 28
+
+/* All module clocks and bus gates are exported except DRAM */
+
+#define CLK_DRAM 49
+
+#define CLK_BUS_DRAM 56
+
+#define CLK_NUMBER (CLK_BUS_HDCP + 1)
+
+#endif /* _CCU_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/clock/sun50i-h616-ccu.h b/include/dt-bindings/clock/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..4fc08b0df2f3
--- /dev/null
+++ b/include/dt-bindings/clock/sun50i-h616-ccu.h
@@ -0,0 +1,115 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN50I_H616_H_
+#define _DT_BINDINGS_CLK_SUN50I_H616_H_
+
+#define CLK_PLL_PERIPH0 4
+
+#define CLK_CPUX 21
+
+#define CLK_APB1 26
+
+#define CLK_DE 29
+#define CLK_BUS_DE 30
+#define CLK_DEINTERLACE 31
+#define CLK_BUS_DEINTERLACE 32
+#define CLK_G2D 33
+#define CLK_BUS_G2D 34
+#define CLK_GPU0 35
+#define CLK_BUS_GPU 36
+#define CLK_GPU1 37
+#define CLK_CE 38
+#define CLK_BUS_CE 39
+#define CLK_VE 40
+#define CLK_BUS_VE 41
+#define CLK_BUS_DMA 42
+#define CLK_BUS_HSTIMER 43
+#define CLK_AVS 44
+#define CLK_BUS_DBG 45
+#define CLK_BUS_PSI 46
+#define CLK_BUS_PWM 47
+#define CLK_BUS_IOMMU 48
+
+#define CLK_MBUS_DMA 50
+#define CLK_MBUS_VE 51
+#define CLK_MBUS_CE 52
+#define CLK_MBUS_TS 53
+#define CLK_MBUS_NAND 54
+#define CLK_MBUS_G2D 55
+
+#define CLK_NAND0 57
+#define CLK_NAND1 58
+#define CLK_BUS_NAND 59
+#define CLK_MMC0 60
+#define CLK_MMC1 61
+#define CLK_MMC2 62
+#define CLK_BUS_MMC0 63
+#define CLK_BUS_MMC1 64
+#define CLK_BUS_MMC2 65
+#define CLK_BUS_UART0 66
+#define CLK_BUS_UART1 67
+#define CLK_BUS_UART2 68
+#define CLK_BUS_UART3 69
+#define CLK_BUS_UART4 70
+#define CLK_BUS_UART5 71
+#define CLK_BUS_I2C0 72
+#define CLK_BUS_I2C1 73
+#define CLK_BUS_I2C2 74
+#define CLK_BUS_I2C3 75
+#define CLK_BUS_I2C4 76
+#define CLK_SPI0 77
+#define CLK_SPI1 78
+#define CLK_BUS_SPI0 79
+#define CLK_BUS_SPI1 80
+#define CLK_EMAC_25M 81
+#define CLK_BUS_EMAC0 82
+#define CLK_BUS_EMAC1 83
+#define CLK_TS 84
+#define CLK_BUS_TS 85
+#define CLK_BUS_THS 86
+#define CLK_SPDIF 87
+#define CLK_BUS_SPDIF 88
+#define CLK_DMIC 89
+#define CLK_BUS_DMIC 90
+#define CLK_AUDIO_CODEC_1X 91
+#define CLK_AUDIO_CODEC_4X 92
+#define CLK_BUS_AUDIO_CODEC 93
+#define CLK_AUDIO_HUB 94
+#define CLK_BUS_AUDIO_HUB 95
+#define CLK_USB_OHCI0 96
+#define CLK_USB_PHY0 97
+#define CLK_USB_OHCI1 98
+#define CLK_USB_PHY1 99
+#define CLK_USB_OHCI2 100
+#define CLK_USB_PHY2 101
+#define CLK_USB_OHCI3 102
+#define CLK_USB_PHY3 103
+#define CLK_BUS_OHCI0 104
+#define CLK_BUS_OHCI1 105
+#define CLK_BUS_OHCI2 106
+#define CLK_BUS_OHCI3 107
+#define CLK_BUS_EHCI0 108
+#define CLK_BUS_EHCI1 109
+#define CLK_BUS_EHCI2 110
+#define CLK_BUS_EHCI3 111
+#define CLK_BUS_OTG 112
+#define CLK_BUS_KEYADC 113
+#define CLK_HDMI 114
+#define CLK_HDMI_SLOW 115
+#define CLK_HDMI_CEC 116
+#define CLK_BUS_HDMI 117
+#define CLK_BUS_TCON_TOP 118
+#define CLK_TCON_TV0 119
+#define CLK_TCON_TV1 120
+#define CLK_BUS_TCON_TV0 121
+#define CLK_BUS_TCON_TV1 122
+#define CLK_TVE0 123
+#define CLK_BUS_TVE_TOP 124
+#define CLK_BUS_TVE0 125
+#define CLK_HDCP 126
+#define CLK_BUS_HDCP 127
+
+#endif /* _DT_BINDINGS_CLK_SUN50I_H616_H_ */
diff --git a/include/dt-bindings/reset/sun50i-h616-ccu.h b/include/dt-bindings/reset/sun50i-h616-ccu.h
new file mode 100644
index 000000000000..cb6285a8d128
--- /dev/null
+++ b/include/dt-bindings/reset/sun50i-h616-ccu.h
@@ -0,0 +1,70 @@
+/* SPDX-License-Identifier: (GPL-2.0+ or MIT) */
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+#ifndef _DT_BINDINGS_RESET_SUN50I_H616_H_
+#define _DT_BINDINGS_RESET_SUN50I_H616_H_
+
+#define RST_MBUS 0
+#define RST_BUS_DE 1
+#define RST_BUS_DEINTERLACE 2
+#define RST_BUS_GPU 3
+#define RST_BUS_CE 4
+#define RST_BUS_VE 5
+#define RST_BUS_DMA 6
+#define RST_BUS_HSTIMER 7
+#define RST_BUS_DBG 8
+#define RST_BUS_PSI 9
+#define RST_BUS_PWM 10
+#define RST_BUS_IOMMU 11
+#define RST_BUS_DRAM 12
+#define RST_BUS_NAND 13
+#define RST_BUS_MMC0 14
+#define RST_BUS_MMC1 15
+#define RST_BUS_MMC2 16
+#define RST_BUS_UART0 17
+#define RST_BUS_UART1 18
+#define RST_BUS_UART2 19
+#define RST_BUS_UART3 20
+#define RST_BUS_UART4 21
+#define RST_BUS_UART5 22
+#define RST_BUS_I2C0 23
+#define RST_BUS_I2C1 24
+#define RST_BUS_I2C2 25
+#define RST_BUS_I2C3 26
+#define RST_BUS_I2C4 27
+#define RST_BUS_SPI0 28
+#define RST_BUS_SPI1 29
+#define RST_BUS_EMAC0 30
+#define RST_BUS_EMAC1 31
+#define RST_BUS_TS 32
+#define RST_BUS_THS 33
+#define RST_BUS_SPDIF 34
+#define RST_BUS_DMIC 35
+#define RST_BUS_AUDIO_CODEC 36
+#define RST_BUS_AUDIO_HUB 37
+#define RST_USB_PHY0 38
+#define RST_USB_PHY1 39
+#define RST_USB_PHY2 40
+#define RST_USB_PHY3 41
+#define RST_BUS_OHCI0 42
+#define RST_BUS_OHCI1 43
+#define RST_BUS_OHCI2 44
+#define RST_BUS_OHCI3 45
+#define RST_BUS_EHCI0 46
+#define RST_BUS_EHCI1 47
+#define RST_BUS_EHCI2 48
+#define RST_BUS_EHCI3 49
+#define RST_BUS_OTG 50
+#define RST_BUS_HDMI 51
+#define RST_BUS_HDMI_SUB 52
+#define RST_BUS_TCON_TOP 53
+#define RST_BUS_TCON_TV0 54
+#define RST_BUS_TCON_TV1 55
+#define RST_BUS_TVE_TOP 56
+#define RST_BUS_TVE0 57
+#define RST_BUS_HDCP 58
+#define RST_BUS_KEYADC 59
+
+#endif /* _DT_BINDINGS_RESET_SUN50I_H616_H_ */
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Ulf Hansson,
devicetree
From: Yangtao Li <frank@allwinnertech.com>
Add binding for A100's and H616's mmc and emmc controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
index e82c9a07b6fb..e75b3a8ba816 100644
--- a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
+++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
@@ -26,6 +26,8 @@ properties:
- const: allwinner,sun9i-a80-mmc
- const: allwinner,sun50i-a64-emmc
- const: allwinner,sun50i-a64-mmc
+ - const: allwinner,sun50i-a100-emmc
+ - const: allwinner,sun50i-a100-mmc
- items:
- const: allwinner,sun8i-a83t-mmc
- const: allwinner,sun7i-a20-mmc
@@ -47,6 +49,12 @@ properties:
- items:
- const: allwinner,sun50i-h6-mmc
- const: allwinner,sun50i-a64-mmc
+ - items:
+ - const: allwinner,sun50i-h616-emmc
+ - const: allwinner,sun50i-a100-emmc
+ - items:
+ - const: allwinner,sun50i-h616-mmc
+ - const: allwinner,sun50i-a100-mmc
reg:
maxItems: 1
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Ulf Hansson, devicetree, Yangtao Li, Linus Walleij,
linux-kernel, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Add binding for A100's and H616's mmc and emmc controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
1 file changed, 8 insertions(+)
diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
index e82c9a07b6fb..e75b3a8ba816 100644
--- a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
+++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
@@ -26,6 +26,8 @@ properties:
- const: allwinner,sun9i-a80-mmc
- const: allwinner,sun50i-a64-emmc
- const: allwinner,sun50i-a64-mmc
+ - const: allwinner,sun50i-a100-emmc
+ - const: allwinner,sun50i-a100-mmc
- items:
- const: allwinner,sun8i-a83t-mmc
- const: allwinner,sun7i-a20-mmc
@@ -47,6 +49,12 @@ properties:
- items:
- const: allwinner,sun50i-h6-mmc
- const: allwinner,sun50i-a64-mmc
+ - items:
+ - const: allwinner,sun50i-h616-emmc
+ - const: allwinner,sun50i-a100-emmc
+ - items:
+ - const: allwinner,sun50i-h616-mmc
+ - const: allwinner,sun50i-a100-mmc
reg:
maxItems: 1
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:54 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:54 UTC (permalink / raw)
To: Andre Przywara
Cc: Jernej Skrabec, linux-kernel, linux-arm-kernel, Ulf Hansson,
Chen-Yu Tsai, Yangtao Li, linux-sunxi, Linus Walleij,
Clément Péron, Maxime Ripard, Icenowy Zheng,
devicetree, Shuosheng Huang
On Fri, 11 Dec 2020 01:19:21 +0000, Andre Przywara wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add binding for A100's and H616's mmc and emmc controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
@ 2020-12-14 22:54 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:54 UTC (permalink / raw)
To: Andre Przywara
Cc: devicetree, Ulf Hansson, Yangtao Li, linux-sunxi, Jernej Skrabec,
Maxime Ripard, linux-kernel, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
Linus Walleij, linux-arm-kernel
On Fri, 11 Dec 2020 01:19:21 +0000, Andre Przywara wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add binding for A100's and H616's mmc and emmc controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
2020-12-11 1:19 ` Andre Przywara
@ 2021-01-11 18:06 ` Ulf Hansson
-1 siblings, 0 replies; 98+ messages in thread
From: Ulf Hansson @ 2021-01-11 18:06 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, Linux ARM,
Linux Kernel Mailing List, linux-sunxi, DTML
On Fri, 11 Dec 2020 at 02:20, Andre Przywara <andre.przywara@arm.com> wrote:
>
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add binding for A100's and H616's mmc and emmc controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Applied for next to my mmc tree, thanks!
Kind regards
Uffe
> ---
> .../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> index e82c9a07b6fb..e75b3a8ba816 100644
> --- a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> +++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> @@ -26,6 +26,8 @@ properties:
> - const: allwinner,sun9i-a80-mmc
> - const: allwinner,sun50i-a64-emmc
> - const: allwinner,sun50i-a64-mmc
> + - const: allwinner,sun50i-a100-emmc
> + - const: allwinner,sun50i-a100-mmc
> - items:
> - const: allwinner,sun8i-a83t-mmc
> - const: allwinner,sun7i-a20-mmc
> @@ -47,6 +49,12 @@ properties:
> - items:
> - const: allwinner,sun50i-h6-mmc
> - const: allwinner,sun50i-a64-mmc
> + - items:
> + - const: allwinner,sun50i-h616-emmc
> + - const: allwinner,sun50i-a100-emmc
> + - items:
> + - const: allwinner,sun50i-h616-mmc
> + - const: allwinner,sun50i-a100-mmc
>
> reg:
> maxItems: 1
> --
> 2.17.5
>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 08/21] dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
@ 2021-01-11 18:06 ` Ulf Hansson
0 siblings, 0 replies; 98+ messages in thread
From: Ulf Hansson @ 2021-01-11 18:06 UTC (permalink / raw)
To: Andre Przywara
Cc: Jernej Skrabec, DTML, Yangtao Li, Linus Walleij, linux-sunxi,
Linux Kernel Mailing List, Maxime Ripard, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
Linux ARM
On Fri, 11 Dec 2020 at 02:20, Andre Przywara <andre.przywara@arm.com> wrote:
>
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add binding for A100's and H616's mmc and emmc controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Applied for next to my mmc tree, thanks!
Kind regards
Uffe
> ---
> .../devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 ++++++++
> 1 file changed, 8 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> index e82c9a07b6fb..e75b3a8ba816 100644
> --- a/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> +++ b/Documentation/devicetree/bindings/mmc/allwinner,sun4i-a10-mmc.yaml
> @@ -26,6 +26,8 @@ properties:
> - const: allwinner,sun9i-a80-mmc
> - const: allwinner,sun50i-a64-emmc
> - const: allwinner,sun50i-a64-mmc
> + - const: allwinner,sun50i-a100-emmc
> + - const: allwinner,sun50i-a100-mmc
> - items:
> - const: allwinner,sun8i-a83t-mmc
> - const: allwinner,sun7i-a20-mmc
> @@ -47,6 +49,12 @@ properties:
> - items:
> - const: allwinner,sun50i-h6-mmc
> - const: allwinner,sun50i-a64-mmc
> + - items:
> + - const: allwinner,sun50i-h616-emmc
> + - const: allwinner,sun50i-a100-emmc
> + - items:
> + - const: allwinner,sun50i-h616-mmc
> + - const: allwinner,sun50i-a100-mmc
>
> reg:
> maxItems: 1
> --
> 2.17.5
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 09/21] mmc: sunxi: add support for A100 mmc controller
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Ulf Hansson,
linux-mmc
From: Yangtao Li <frank@allwinnertech.com>
This patch adds support for A100 MMC controller, which use word address
for internal dma.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/mmc/host/sunxi-mmc.c | 28 +++++++++++++++++++++++++---
1 file changed, 25 insertions(+), 3 deletions(-)
diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
index fc62773602ec..1518b64112b7 100644
--- a/drivers/mmc/host/sunxi-mmc.c
+++ b/drivers/mmc/host/sunxi-mmc.c
@@ -244,6 +244,7 @@ struct sunxi_idma_des {
struct sunxi_mmc_cfg {
u32 idma_des_size_bits;
+ u32 idma_des_shift;
const struct sunxi_mmc_clk_delay *clk_delays;
/* does the IP block support autocalibration? */
@@ -343,7 +344,7 @@ static int sunxi_mmc_init_host(struct sunxi_mmc_host *host)
/* Enable CEATA support */
mmc_writel(host, REG_FUNS, SDXC_CEATA_ON);
/* Set DMA descriptor list base address */
- mmc_writel(host, REG_DLBA, host->sg_dma);
+ mmc_writel(host, REG_DLBA, host->sg_dma >> host->cfg->idma_des_shift);
rval = mmc_readl(host, REG_GCTRL);
rval |= SDXC_INTERRUPT_ENABLE_BIT;
@@ -373,8 +374,10 @@ static void sunxi_mmc_init_idma_des(struct sunxi_mmc_host *host,
next_desc += sizeof(struct sunxi_idma_des);
pdes[i].buf_addr_ptr1 =
- cpu_to_le32(sg_dma_address(&data->sg[i]));
- pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc);
+ cpu_to_le32(sg_dma_address(&data->sg[i]) >>
+ host->cfg->idma_des_shift);
+ pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc >>
+ host->cfg->idma_des_shift);
}
pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
@@ -1178,6 +1181,23 @@ static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
.needs_new_timings = true,
};
+static const struct sunxi_mmc_cfg sun50i_a100_cfg = {
+ .idma_des_size_bits = 16,
+ .idma_des_shift = 2,
+ .clk_delays = NULL,
+ .can_calibrate = true,
+ .mask_data0 = true,
+ .needs_new_timings = true,
+};
+
+static const struct sunxi_mmc_cfg sun50i_a100_emmc_cfg = {
+ .idma_des_size_bits = 13,
+ .idma_des_shift = 2,
+ .clk_delays = NULL,
+ .can_calibrate = true,
+ .needs_new_timings = true,
+};
+
static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
{ .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
@@ -1186,6 +1206,8 @@ static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
{ .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
{ .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
+ { .compatible = "allwinner,sun50i-a100-mmc", .data = &sun50i_a100_cfg },
+ { .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 09/21] mmc: sunxi: add support for A100 mmc controller
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Ulf Hansson, Yangtao Li, Linus Walleij, linux-mmc,
linux-kernel, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
This patch adds support for A100 MMC controller, which use word address
for internal dma.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/mmc/host/sunxi-mmc.c | 28 +++++++++++++++++++++++++---
1 file changed, 25 insertions(+), 3 deletions(-)
diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
index fc62773602ec..1518b64112b7 100644
--- a/drivers/mmc/host/sunxi-mmc.c
+++ b/drivers/mmc/host/sunxi-mmc.c
@@ -244,6 +244,7 @@ struct sunxi_idma_des {
struct sunxi_mmc_cfg {
u32 idma_des_size_bits;
+ u32 idma_des_shift;
const struct sunxi_mmc_clk_delay *clk_delays;
/* does the IP block support autocalibration? */
@@ -343,7 +344,7 @@ static int sunxi_mmc_init_host(struct sunxi_mmc_host *host)
/* Enable CEATA support */
mmc_writel(host, REG_FUNS, SDXC_CEATA_ON);
/* Set DMA descriptor list base address */
- mmc_writel(host, REG_DLBA, host->sg_dma);
+ mmc_writel(host, REG_DLBA, host->sg_dma >> host->cfg->idma_des_shift);
rval = mmc_readl(host, REG_GCTRL);
rval |= SDXC_INTERRUPT_ENABLE_BIT;
@@ -373,8 +374,10 @@ static void sunxi_mmc_init_idma_des(struct sunxi_mmc_host *host,
next_desc += sizeof(struct sunxi_idma_des);
pdes[i].buf_addr_ptr1 =
- cpu_to_le32(sg_dma_address(&data->sg[i]));
- pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc);
+ cpu_to_le32(sg_dma_address(&data->sg[i]) >>
+ host->cfg->idma_des_shift);
+ pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc >>
+ host->cfg->idma_des_shift);
}
pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
@@ -1178,6 +1181,23 @@ static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
.needs_new_timings = true,
};
+static const struct sunxi_mmc_cfg sun50i_a100_cfg = {
+ .idma_des_size_bits = 16,
+ .idma_des_shift = 2,
+ .clk_delays = NULL,
+ .can_calibrate = true,
+ .mask_data0 = true,
+ .needs_new_timings = true,
+};
+
+static const struct sunxi_mmc_cfg sun50i_a100_emmc_cfg = {
+ .idma_des_size_bits = 13,
+ .idma_des_shift = 2,
+ .clk_delays = NULL,
+ .can_calibrate = true,
+ .needs_new_timings = true,
+};
+
static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
{ .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
@@ -1186,6 +1206,8 @@ static const struct of_device_id sunxi_mmc_of_match[] = {
{ .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
{ .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
{ .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
+ { .compatible = "allwinner,sun50i-a100-mmc", .data = &sun50i_a100_cfg },
+ { .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
{ /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 09/21] mmc: sunxi: add support for A100 mmc controller
2020-12-11 1:19 ` Andre Przywara
@ 2021-01-11 18:06 ` Ulf Hansson
-1 siblings, 0 replies; 98+ messages in thread
From: Ulf Hansson @ 2021-01-11 18:06 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, Linux ARM,
Linux Kernel Mailing List, linux-sunxi, linux-mmc
On Fri, 11 Dec 2020 at 02:20, Andre Przywara <andre.przywara@arm.com> wrote:
>
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch adds support for A100 MMC controller, which use word address
> for internal dma.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Applied for next to my mmc tree, thanks!
Kind regards
Uffe
> ---
> drivers/mmc/host/sunxi-mmc.c | 28 +++++++++++++++++++++++++---
> 1 file changed, 25 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
> index fc62773602ec..1518b64112b7 100644
> --- a/drivers/mmc/host/sunxi-mmc.c
> +++ b/drivers/mmc/host/sunxi-mmc.c
> @@ -244,6 +244,7 @@ struct sunxi_idma_des {
>
> struct sunxi_mmc_cfg {
> u32 idma_des_size_bits;
> + u32 idma_des_shift;
> const struct sunxi_mmc_clk_delay *clk_delays;
>
> /* does the IP block support autocalibration? */
> @@ -343,7 +344,7 @@ static int sunxi_mmc_init_host(struct sunxi_mmc_host *host)
> /* Enable CEATA support */
> mmc_writel(host, REG_FUNS, SDXC_CEATA_ON);
> /* Set DMA descriptor list base address */
> - mmc_writel(host, REG_DLBA, host->sg_dma);
> + mmc_writel(host, REG_DLBA, host->sg_dma >> host->cfg->idma_des_shift);
>
> rval = mmc_readl(host, REG_GCTRL);
> rval |= SDXC_INTERRUPT_ENABLE_BIT;
> @@ -373,8 +374,10 @@ static void sunxi_mmc_init_idma_des(struct sunxi_mmc_host *host,
>
> next_desc += sizeof(struct sunxi_idma_des);
> pdes[i].buf_addr_ptr1 =
> - cpu_to_le32(sg_dma_address(&data->sg[i]));
> - pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc);
> + cpu_to_le32(sg_dma_address(&data->sg[i]) >>
> + host->cfg->idma_des_shift);
> + pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc >>
> + host->cfg->idma_des_shift);
> }
>
> pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
> @@ -1178,6 +1181,23 @@ static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
> .needs_new_timings = true,
> };
>
> +static const struct sunxi_mmc_cfg sun50i_a100_cfg = {
> + .idma_des_size_bits = 16,
> + .idma_des_shift = 2,
> + .clk_delays = NULL,
> + .can_calibrate = true,
> + .mask_data0 = true,
> + .needs_new_timings = true,
> +};
> +
> +static const struct sunxi_mmc_cfg sun50i_a100_emmc_cfg = {
> + .idma_des_size_bits = 13,
> + .idma_des_shift = 2,
> + .clk_delays = NULL,
> + .can_calibrate = true,
> + .needs_new_timings = true,
> +};
> +
> static const struct of_device_id sunxi_mmc_of_match[] = {
> { .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
> { .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
> @@ -1186,6 +1206,8 @@ static const struct of_device_id sunxi_mmc_of_match[] = {
> { .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
> { .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
> { .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
> + { .compatible = "allwinner,sun50i-a100-mmc", .data = &sun50i_a100_cfg },
> + { .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
> --
> 2.17.5
>
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 09/21] mmc: sunxi: add support for A100 mmc controller
@ 2021-01-11 18:06 ` Ulf Hansson
0 siblings, 0 replies; 98+ messages in thread
From: Ulf Hansson @ 2021-01-11 18:06 UTC (permalink / raw)
To: Andre Przywara
Cc: Jernej Skrabec, Yangtao Li, Linus Walleij, linux-sunxi,
linux-mmc, Linux Kernel Mailing List, Maxime Ripard,
Chen-Yu Tsai, Clément Péron, Icenowy Zheng,
Shuosheng Huang, Linux ARM
On Fri, 11 Dec 2020 at 02:20, Andre Przywara <andre.przywara@arm.com> wrote:
>
> From: Yangtao Li <frank@allwinnertech.com>
>
> This patch adds support for A100 MMC controller, which use word address
> for internal dma.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Applied for next to my mmc tree, thanks!
Kind regards
Uffe
> ---
> drivers/mmc/host/sunxi-mmc.c | 28 +++++++++++++++++++++++++---
> 1 file changed, 25 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/mmc/host/sunxi-mmc.c b/drivers/mmc/host/sunxi-mmc.c
> index fc62773602ec..1518b64112b7 100644
> --- a/drivers/mmc/host/sunxi-mmc.c
> +++ b/drivers/mmc/host/sunxi-mmc.c
> @@ -244,6 +244,7 @@ struct sunxi_idma_des {
>
> struct sunxi_mmc_cfg {
> u32 idma_des_size_bits;
> + u32 idma_des_shift;
> const struct sunxi_mmc_clk_delay *clk_delays;
>
> /* does the IP block support autocalibration? */
> @@ -343,7 +344,7 @@ static int sunxi_mmc_init_host(struct sunxi_mmc_host *host)
> /* Enable CEATA support */
> mmc_writel(host, REG_FUNS, SDXC_CEATA_ON);
> /* Set DMA descriptor list base address */
> - mmc_writel(host, REG_DLBA, host->sg_dma);
> + mmc_writel(host, REG_DLBA, host->sg_dma >> host->cfg->idma_des_shift);
>
> rval = mmc_readl(host, REG_GCTRL);
> rval |= SDXC_INTERRUPT_ENABLE_BIT;
> @@ -373,8 +374,10 @@ static void sunxi_mmc_init_idma_des(struct sunxi_mmc_host *host,
>
> next_desc += sizeof(struct sunxi_idma_des);
> pdes[i].buf_addr_ptr1 =
> - cpu_to_le32(sg_dma_address(&data->sg[i]));
> - pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc);
> + cpu_to_le32(sg_dma_address(&data->sg[i]) >>
> + host->cfg->idma_des_shift);
> + pdes[i].buf_addr_ptr2 = cpu_to_le32((u32)next_desc >>
> + host->cfg->idma_des_shift);
> }
>
> pdes[0].config |= cpu_to_le32(SDXC_IDMAC_DES0_FD);
> @@ -1178,6 +1181,23 @@ static const struct sunxi_mmc_cfg sun50i_a64_emmc_cfg = {
> .needs_new_timings = true,
> };
>
> +static const struct sunxi_mmc_cfg sun50i_a100_cfg = {
> + .idma_des_size_bits = 16,
> + .idma_des_shift = 2,
> + .clk_delays = NULL,
> + .can_calibrate = true,
> + .mask_data0 = true,
> + .needs_new_timings = true,
> +};
> +
> +static const struct sunxi_mmc_cfg sun50i_a100_emmc_cfg = {
> + .idma_des_size_bits = 13,
> + .idma_des_shift = 2,
> + .clk_delays = NULL,
> + .can_calibrate = true,
> + .needs_new_timings = true,
> +};
> +
> static const struct of_device_id sunxi_mmc_of_match[] = {
> { .compatible = "allwinner,sun4i-a10-mmc", .data = &sun4i_a10_cfg },
> { .compatible = "allwinner,sun5i-a13-mmc", .data = &sun5i_a13_cfg },
> @@ -1186,6 +1206,8 @@ static const struct of_device_id sunxi_mmc_of_match[] = {
> { .compatible = "allwinner,sun9i-a80-mmc", .data = &sun9i_a80_cfg },
> { .compatible = "allwinner,sun50i-a64-mmc", .data = &sun50i_a64_cfg },
> { .compatible = "allwinner,sun50i-a64-emmc", .data = &sun50i_a64_emmc_cfg },
> + { .compatible = "allwinner,sun50i-a100-mmc", .data = &sun50i_a100_cfg },
> + { .compatible = "allwinner,sun50i-a100-emmc", .data = &sun50i_a100_emmc_cfg },
> { /* sentinel */ }
> };
> MODULE_DEVICE_TABLE(of, sunxi_mmc_of_match);
> --
> 2.17.5
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 10/21] mfd: axp20x: Allow AXP chips without interrupt lines
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Lee Jones
Currently the AXP chip requires to have its IRQ line connected to some
interrupt controller, and will fail probing when this is not the case.
On a new Allwinner SoC (H616) there is no NMI pin anymore, so the
interrupt functionality of the AXP chip is simply not available.
Check whether the DT describes the AXP chip as an interrupt controller
before trying to register the irqchip, to avoid probe failures on
setups without an interrupt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/mfd/axp20x.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index aa59496e4376..a52595c49d40 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -959,12 +959,17 @@ int axp20x_device_probe(struct axp20x_dev *axp20x)
AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE);
}
- ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
- IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
- -1, axp20x->regmap_irq_chip, &axp20x->regmap_irqc);
- if (ret) {
- dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret);
- return ret;
+ if (!axp20x->dev->of_node ||
+ of_property_read_bool(axp20x->dev->of_node, "interrupt-controller")) {
+ ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
+ IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
+ -1, axp20x->regmap_irq_chip,
+ &axp20x->regmap_irqc);
+ if (ret) {
+ dev_err(axp20x->dev, "failed to add irq chip: %d\n",
+ ret);
+ return ret;
+ }
}
ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 10/21] mfd: axp20x: Allow AXP chips without interrupt lines
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, Lee Jones, linux-arm-kernel
Currently the AXP chip requires to have its IRQ line connected to some
interrupt controller, and will fail probing when this is not the case.
On a new Allwinner SoC (H616) there is no NMI pin anymore, so the
interrupt functionality of the AXP chip is simply not available.
Check whether the DT describes the AXP chip as an interrupt controller
before trying to register the irqchip, to avoid probe failures on
setups without an interrupt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/mfd/axp20x.c | 17 +++++++++++------
1 file changed, 11 insertions(+), 6 deletions(-)
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index aa59496e4376..a52595c49d40 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -959,12 +959,17 @@ int axp20x_device_probe(struct axp20x_dev *axp20x)
AXP806_REG_ADDR_EXT_ADDR_SLAVE_MODE);
}
- ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
- IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
- -1, axp20x->regmap_irq_chip, &axp20x->regmap_irqc);
- if (ret) {
- dev_err(axp20x->dev, "failed to add irq chip: %d\n", ret);
- return ret;
+ if (!axp20x->dev->of_node ||
+ of_property_read_bool(axp20x->dev->of_node, "interrupt-controller")) {
+ ret = regmap_add_irq_chip(axp20x->regmap, axp20x->irq,
+ IRQF_ONESHOT | IRQF_SHARED | axp20x->irq_flags,
+ -1, axp20x->regmap_irq_chip,
+ &axp20x->regmap_irqc);
+ if (ret) {
+ dev_err(axp20x->dev, "failed to add irq chip: %d\n",
+ ret);
+ return ret;
+ }
}
ret = mfd_add_devices(axp20x->dev, -1, axp20x->cells,
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 11/21] dt-bindings: sram: sunxi-sram: Add H616 compatible string
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, devicetree
The H616 adds a second EMAC clock register. We don't know about the
exact SRAM properties yet, so this gets omitted for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/sram/allwinner,sun4i-a10-system-control.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
index b66a07e21d1e..1c426c211e36 100644
--- a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
+++ b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
@@ -49,6 +49,7 @@ properties:
- items:
- const: allwinner,suniv-f1c100s-system-control
- const: allwinner,sun4i-a10-system-control
+ - const: allwinner,sun50i-h616-system-control
reg:
maxItems: 1
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 11/21] dt-bindings: sram: sunxi-sram: Add H616 compatible string
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
The H616 adds a second EMAC clock register. We don't know about the
exact SRAM properties yet, so this gets omitted for now.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/sram/allwinner,sun4i-a10-system-control.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
index b66a07e21d1e..1c426c211e36 100644
--- a/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
+++ b/Documentation/devicetree/bindings/sram/allwinner,sun4i-a10-system-control.yaml
@@ -49,6 +49,7 @@ properties:
- items:
- const: allwinner,suniv-f1c100s-system-control
- const: allwinner,sun4i-a10-system-control
+ - const: allwinner,sun50i-h616-system-control
reg:
maxItems: 1
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 11/21] dt-bindings: sram: sunxi-sram: Add H616 compatible string
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:54 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:54 UTC (permalink / raw)
To: Andre Przywara
Cc: devicetree, Jernej Skrabec, Chen-Yu Tsai, Yangtao Li,
linux-kernel, linux-sunxi, Linus Walleij, Maxime Ripard,
Icenowy Zheng, Clément Péron, linux-arm-kernel,
Shuosheng Huang
On Fri, 11 Dec 2020 01:19:24 +0000, Andre Przywara wrote:
> The H616 adds a second EMAC clock register. We don't know about the
> exact SRAM properties yet, so this gets omitted for now.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/sram/allwinner,sun4i-a10-system-control.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 11/21] dt-bindings: sram: sunxi-sram: Add H616 compatible string
@ 2020-12-14 22:54 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:54 UTC (permalink / raw)
To: Andre Przywara
Cc: devicetree, Jernej Skrabec, Yangtao Li, Linus Walleij,
Chen-Yu Tsai, Maxime Ripard, linux-kernel, linux-sunxi,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
On Fri, 11 Dec 2020 01:19:24 +0000, Andre Przywara wrote:
> The H616 adds a second EMAC clock register. We don't know about the
> exact SRAM properties yet, so this gets omitted for now.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/sram/allwinner,sun4i-a10-system-control.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 12/21] soc: sunxi: sram: Add support for more than one EMAC clock
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi
The Allwinner H616 adds a second EMAC clock register at offset 0x34, for
controlling the second EMAC in this chip.
Allow to extend the regmap in this case, to cover more than the current
4 bytes exported.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/soc/sunxi/sunxi_sram.c | 31 +++++++++++++++++++++++--------
1 file changed, 23 insertions(+), 8 deletions(-)
diff --git a/drivers/soc/sunxi/sunxi_sram.c b/drivers/soc/sunxi/sunxi_sram.c
index d4c7bd59429e..42833e33a96c 100644
--- a/drivers/soc/sunxi/sunxi_sram.c
+++ b/drivers/soc/sunxi/sunxi_sram.c
@@ -283,7 +283,7 @@ int sunxi_sram_release(struct device *dev)
EXPORT_SYMBOL(sunxi_sram_release);
struct sunxi_sramc_variant {
- bool has_emac_clock;
+ int num_emac_clocks;
};
static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
@@ -291,20 +291,31 @@ static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
};
static const struct sunxi_sramc_variant sun8i_h3_sramc_variant = {
- .has_emac_clock = true,
+ .num_emac_clocks = 1,
};
static const struct sunxi_sramc_variant sun50i_a64_sramc_variant = {
- .has_emac_clock = true,
+ .num_emac_clocks = 1,
+};
+
+static const struct sunxi_sramc_variant sun50i_h616_sramc_variant = {
+ .num_emac_clocks = 2,
};
#define SUNXI_SRAM_EMAC_CLOCK_REG 0x30
static bool sunxi_sram_regmap_accessible_reg(struct device *dev,
unsigned int reg)
{
- if (reg == SUNXI_SRAM_EMAC_CLOCK_REG)
- return true;
- return false;
+ const struct sunxi_sramc_variant *variant;
+
+ variant = of_device_get_match_data(dev);
+
+ if (reg < SUNXI_SRAM_EMAC_CLOCK_REG)
+ return false;
+ if (reg > SUNXI_SRAM_EMAC_CLOCK_REG + variant->num_emac_clocks * 4)
+ return false;
+
+ return true;
}
static struct regmap_config sunxi_sram_emac_clock_regmap = {
@@ -312,7 +323,7 @@ static struct regmap_config sunxi_sram_emac_clock_regmap = {
.val_bits = 32,
.reg_stride = 4,
/* last defined register */
- .max_register = SUNXI_SRAM_EMAC_CLOCK_REG,
+ .max_register = SUNXI_SRAM_EMAC_CLOCK_REG + 4,
/* other devices have no business accessing other registers */
.readable_reg = sunxi_sram_regmap_accessible_reg,
.writeable_reg = sunxi_sram_regmap_accessible_reg,
@@ -343,7 +354,7 @@ static int sunxi_sram_probe(struct platform_device *pdev)
if (!d)
return -ENOMEM;
- if (variant->has_emac_clock) {
+ if (variant->num_emac_clocks > 0) {
emac_clock = devm_regmap_init_mmio(&pdev->dev, base,
&sunxi_sram_emac_clock_regmap);
@@ -387,6 +398,10 @@ static const struct of_device_id sunxi_sram_dt_match[] = {
.compatible = "allwinner,sun50i-h5-system-control",
.data = &sun50i_a64_sramc_variant,
},
+ {
+ .compatible = "allwinner,sun50i-h616-system-control",
+ .data = &sun50i_h616_sramc_variant,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, sunxi_sram_dt_match);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 12/21] soc: sunxi: sram: Add support for more than one EMAC clock
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
The Allwinner H616 adds a second EMAC clock register at offset 0x34, for
controlling the second EMAC in this chip.
Allow to extend the regmap in this case, to cover more than the current
4 bytes exported.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/soc/sunxi/sunxi_sram.c | 31 +++++++++++++++++++++++--------
1 file changed, 23 insertions(+), 8 deletions(-)
diff --git a/drivers/soc/sunxi/sunxi_sram.c b/drivers/soc/sunxi/sunxi_sram.c
index d4c7bd59429e..42833e33a96c 100644
--- a/drivers/soc/sunxi/sunxi_sram.c
+++ b/drivers/soc/sunxi/sunxi_sram.c
@@ -283,7 +283,7 @@ int sunxi_sram_release(struct device *dev)
EXPORT_SYMBOL(sunxi_sram_release);
struct sunxi_sramc_variant {
- bool has_emac_clock;
+ int num_emac_clocks;
};
static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
@@ -291,20 +291,31 @@ static const struct sunxi_sramc_variant sun4i_a10_sramc_variant = {
};
static const struct sunxi_sramc_variant sun8i_h3_sramc_variant = {
- .has_emac_clock = true,
+ .num_emac_clocks = 1,
};
static const struct sunxi_sramc_variant sun50i_a64_sramc_variant = {
- .has_emac_clock = true,
+ .num_emac_clocks = 1,
+};
+
+static const struct sunxi_sramc_variant sun50i_h616_sramc_variant = {
+ .num_emac_clocks = 2,
};
#define SUNXI_SRAM_EMAC_CLOCK_REG 0x30
static bool sunxi_sram_regmap_accessible_reg(struct device *dev,
unsigned int reg)
{
- if (reg == SUNXI_SRAM_EMAC_CLOCK_REG)
- return true;
- return false;
+ const struct sunxi_sramc_variant *variant;
+
+ variant = of_device_get_match_data(dev);
+
+ if (reg < SUNXI_SRAM_EMAC_CLOCK_REG)
+ return false;
+ if (reg > SUNXI_SRAM_EMAC_CLOCK_REG + variant->num_emac_clocks * 4)
+ return false;
+
+ return true;
}
static struct regmap_config sunxi_sram_emac_clock_regmap = {
@@ -312,7 +323,7 @@ static struct regmap_config sunxi_sram_emac_clock_regmap = {
.val_bits = 32,
.reg_stride = 4,
/* last defined register */
- .max_register = SUNXI_SRAM_EMAC_CLOCK_REG,
+ .max_register = SUNXI_SRAM_EMAC_CLOCK_REG + 4,
/* other devices have no business accessing other registers */
.readable_reg = sunxi_sram_regmap_accessible_reg,
.writeable_reg = sunxi_sram_regmap_accessible_reg,
@@ -343,7 +354,7 @@ static int sunxi_sram_probe(struct platform_device *pdev)
if (!d)
return -ENOMEM;
- if (variant->has_emac_clock) {
+ if (variant->num_emac_clocks > 0) {
emac_clock = devm_regmap_init_mmio(&pdev->dev, base,
&sunxi_sram_emac_clock_regmap);
@@ -387,6 +398,10 @@ static const struct of_device_id sunxi_sram_dt_match[] = {
.compatible = "allwinner,sun50i-h5-system-control",
.data = &sun50i_a64_sramc_variant,
},
+ {
+ .compatible = "allwinner,sun50i-h616-system-control",
+ .data = &sun50i_h616_sramc_variant,
+ },
{ },
};
MODULE_DEVICE_TABLE(of, sunxi_sram_dt_match);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 13/21] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Giuseppe Cavallaro,
Alexandre Torgue, Jose Abreu, David S . Miller, Jakub Kicinski,
netdev
The Allwinner H616 SoC has two EMAC controllers, with the second one
being tied to the internal PHY, but also using a separate EMAC clock
register.
To tell the driver about which clock register to use, we add a parameter
to our syscon phandle. The driver will use this value as an index into
the regmap, so that we can address more than the first register, if
needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index 58e0511badba..00c10ec7b693 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -1129,6 +1129,8 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
struct stmmac_priv *priv;
struct net_device *ndev;
struct regmap *regmap;
+ struct reg_field syscon_field;
+ u32 syscon_idx = 0;
ret = stmmac_get_platform_resources(pdev, &stmmac_res);
if (ret)
@@ -1190,8 +1192,12 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
return ret;
}
- gmac->regmap_field = devm_regmap_field_alloc(dev, regmap,
- *gmac->variant->syscon_field);
+ syscon_field = *gmac->variant->syscon_field;
+ ret = of_property_read_u32_index(pdev->dev.of_node, "syscon", 1,
+ &syscon_idx);
+ if (!ret)
+ syscon_field.reg += syscon_idx * sizeof(u32);
+ gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, syscon_field);
if (IS_ERR(gmac->regmap_field)) {
ret = PTR_ERR(gmac->regmap_field);
dev_err(dev, "Unable to map syscon register: %d\n", ret);
@@ -1263,6 +1269,8 @@ static const struct of_device_id sun8i_dwmac_match[] = {
.data = &emac_variant_a64 },
{ .compatible = "allwinner,sun50i-h6-emac",
.data = &emac_variant_h6 },
+ { .compatible = "allwinner,sun50i-h616-emac",
+ .data = &emac_variant_h6 },
{ }
};
MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 13/21] net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Alexandre Torgue, Yangtao Li, netdev, Linus Walleij,
linux-kernel, Jakub Kicinski, linux-sunxi, Jose Abreu,
Clément Péron, Icenowy Zheng, Giuseppe Cavallaro,
Shuosheng Huang, David S . Miller, linux-arm-kernel
The Allwinner H616 SoC has two EMAC controllers, with the second one
being tied to the internal PHY, but also using a separate EMAC clock
register.
To tell the driver about which clock register to use, we add a parameter
to our syscon phandle. The driver will use this value as an index into
the regmap, so that we can address more than the first register, if
needed.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
index 58e0511badba..00c10ec7b693 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-sun8i.c
@@ -1129,6 +1129,8 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
struct stmmac_priv *priv;
struct net_device *ndev;
struct regmap *regmap;
+ struct reg_field syscon_field;
+ u32 syscon_idx = 0;
ret = stmmac_get_platform_resources(pdev, &stmmac_res);
if (ret)
@@ -1190,8 +1192,12 @@ static int sun8i_dwmac_probe(struct platform_device *pdev)
return ret;
}
- gmac->regmap_field = devm_regmap_field_alloc(dev, regmap,
- *gmac->variant->syscon_field);
+ syscon_field = *gmac->variant->syscon_field;
+ ret = of_property_read_u32_index(pdev->dev.of_node, "syscon", 1,
+ &syscon_idx);
+ if (!ret)
+ syscon_field.reg += syscon_idx * sizeof(u32);
+ gmac->regmap_field = devm_regmap_field_alloc(dev, regmap, syscon_field);
if (IS_ERR(gmac->regmap_field)) {
ret = PTR_ERR(gmac->regmap_field);
dev_err(dev, "Unable to map syscon register: %d\n", ret);
@@ -1263,6 +1269,8 @@ static const struct of_device_id sun8i_dwmac_match[] = {
.data = &emac_variant_a64 },
{ .compatible = "allwinner,sun50i-h6-emac",
.data = &emac_variant_h6 },
+ { .compatible = "allwinner,sun50i-h616-emac",
+ .data = &emac_variant_h6 },
{ }
};
MODULE_DEVICE_TABLE(of, sun8i_dwmac_match);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread
* [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
Newer SoCs (A100, H616) need to clear a different bit in our "unknown"
PMU PHY register.
Generalise the existing code by allowing configs to specify a bitmask
of bits to clear.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++----------------
1 file changed, 11 insertions(+), 17 deletions(-)
diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 651d5e2a25ce..4ba0699e0bb4 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
int hsic_index;
enum sun4i_usb_phy_type type;
u32 disc_thresh;
+ u32 pmu_unk1_clrbits;
u8 phyctl_offset;
bool dedicated_clocks;
- bool enable_pmu_unk1;
bool phy0_dual_route;
int missing_phys;
};
@@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
return ret;
}
+ if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
+ val = readl(phy->pmu + REG_PMU_UNK1);
+ val &= ~data->cfg->pmu_unk1_clrbits;
+ writel(val, phy->pmu + REG_PMU_UNK1);
+ }
+
if (data->cfg->type == sun8i_a83t_phy ||
data->cfg->type == sun50i_h6_phy) {
if (phy->index == 0) {
@@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
writel(val, data->base + data->cfg->phyctl_offset);
}
} else {
- if (phy->pmu && data->cfg->enable_pmu_unk1) {
- val = readl(phy->pmu + REG_PMU_UNK1);
- writel(val & ~2, phy->pmu + REG_PMU_UNK1);
- }
-
/* Enable USB 45 Ohm resistor calibration */
if (phy->index == 0)
sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
@@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
.disc_thresh = 2,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
.disc_thresh = 2,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
@@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
.phy0_dual_route = true,
.missing_phys = BIT(1) | BIT(2),
};
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Vinod Koul, Yangtao Li, Linus Walleij, linux-kernel,
Kishon Vijay Abraham I, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
Newer SoCs (A100, H616) need to clear a different bit in our "unknown"
PMU PHY register.
Generalise the existing code by allowing configs to specify a bitmask
of bits to clear.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++----------------
1 file changed, 11 insertions(+), 17 deletions(-)
diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 651d5e2a25ce..4ba0699e0bb4 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
int hsic_index;
enum sun4i_usb_phy_type type;
u32 disc_thresh;
+ u32 pmu_unk1_clrbits;
u8 phyctl_offset;
bool dedicated_clocks;
- bool enable_pmu_unk1;
bool phy0_dual_route;
int missing_phys;
};
@@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
return ret;
}
+ if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
+ val = readl(phy->pmu + REG_PMU_UNK1);
+ val &= ~data->cfg->pmu_unk1_clrbits;
+ writel(val, phy->pmu + REG_PMU_UNK1);
+ }
+
if (data->cfg->type == sun8i_a83t_phy ||
data->cfg->type == sun50i_h6_phy) {
if (phy->index == 0) {
@@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
writel(val, data->base + data->cfg->phyctl_offset);
}
} else {
- if (phy->pmu && data->cfg->enable_pmu_unk1) {
- val = readl(phy->pmu + REG_PMU_UNK1);
- writel(val & ~2, phy->pmu + REG_PMU_UNK1);
- }
-
/* Enable USB 45 Ohm resistor calibration */
if (phy->index == 0)
sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
@@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg sun4i_a10_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
@@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
.disc_thresh = 2,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
@@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
@@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
.disc_thresh = 2,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = false,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
@@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A10,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
@@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = false,
};
static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
@@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg sun8i_r40_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg sun8i_v3s_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg sun50i_a64_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
+ .pmu_unk1_clrbits = BIT(1),
.phy0_dual_route = true,
};
@@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = {
.disc_thresh = 3,
.phyctl_offset = REG_PHYCTL_A33,
.dedicated_clocks = true,
- .enable_pmu_unk1 = true,
.phy0_dual_route = true,
.missing_phys = BIT(1) | BIT(2),
};
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-13 18:24 ` Icenowy Zheng
-1 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-13 18:24 UTC (permalink / raw)
To: Andre Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> Newer SoCs (A100, H616) need to clear a different bit in our
> "unknown"
> PMU PHY register.
It looks like that the unknown PHY register is PHYCTL register for each
individual PHY, and the bit that is cleared is
called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
>
> Generalise the existing code by allowing configs to specify a bitmask
> of bits to clear.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++------------
> ----
> 1 file changed, 11 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
> b/drivers/phy/allwinner/phy-sun4i-usb.c
> index 651d5e2a25ce..4ba0699e0bb4 100644
> --- a/drivers/phy/allwinner/phy-sun4i-usb.c
> +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
> @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
> int hsic_index;
> enum sun4i_usb_phy_type type;
> u32 disc_thresh;
> + u32 pmu_unk1_clrbits;
> u8 phyctl_offset;
> bool dedicated_clocks;
> - bool enable_pmu_unk1;
> bool phy0_dual_route;
> int missing_phys;
> };
> @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> return ret;
> }
>
> + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
> + val = readl(phy->pmu + REG_PMU_UNK1);
> + val &= ~data->cfg->pmu_unk1_clrbits;
> + writel(val, phy->pmu + REG_PMU_UNK1);
> + }
> +
> if (data->cfg->type == sun8i_a83t_phy ||
> data->cfg->type == sun50i_h6_phy) {
> if (phy->index == 0) {
> @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> writel(val, data->base + data->cfg-
> >phyctl_offset);
> }
> } else {
> - if (phy->pmu && data->cfg->enable_pmu_unk1) {
> - val = readl(phy->pmu + REG_PMU_UNK1);
> - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
> - }
> -
> /* Enable USB 45 Ohm resistor calibration */
> if (phy->index == 0)
> sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
> 0x01, 1);
> @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
> sun4i_a10_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
> @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
> sun5i_a13_cfg = {
> .disc_thresh = 2,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
> @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
> sun6i_a31_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
> @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
> sun7i_a20_cfg = {
> .disc_thresh = 2,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
> @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
> sun8i_a23_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
> @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
> sun8i_a33_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
> @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_h3_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_r40_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_v3s_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
> sun50i_a64_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
> sun50i_h6_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> .phy0_dual_route = true,
> .missing_phys = BIT(1) | BIT(2),
> };
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
@ 2020-12-13 18:24 ` Icenowy Zheng
0 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-13 18:24 UTC (permalink / raw)
To: Andre Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Vinod Koul, Yangtao Li, Linus Walleij, linux-kernel,
Kishon Vijay Abraham I, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> Newer SoCs (A100, H616) need to clear a different bit in our
> "unknown"
> PMU PHY register.
It looks like that the unknown PHY register is PHYCTL register for each
individual PHY, and the bit that is cleared is
called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
>
> Generalise the existing code by allowing configs to specify a bitmask
> of bits to clear.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++------------
> ----
> 1 file changed, 11 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
> b/drivers/phy/allwinner/phy-sun4i-usb.c
> index 651d5e2a25ce..4ba0699e0bb4 100644
> --- a/drivers/phy/allwinner/phy-sun4i-usb.c
> +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
> @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
> int hsic_index;
> enum sun4i_usb_phy_type type;
> u32 disc_thresh;
> + u32 pmu_unk1_clrbits;
> u8 phyctl_offset;
> bool dedicated_clocks;
> - bool enable_pmu_unk1;
> bool phy0_dual_route;
> int missing_phys;
> };
> @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> return ret;
> }
>
> + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
> + val = readl(phy->pmu + REG_PMU_UNK1);
> + val &= ~data->cfg->pmu_unk1_clrbits;
> + writel(val, phy->pmu + REG_PMU_UNK1);
> + }
> +
> if (data->cfg->type == sun8i_a83t_phy ||
> data->cfg->type == sun50i_h6_phy) {
> if (phy->index == 0) {
> @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
> writel(val, data->base + data->cfg-
> >phyctl_offset);
> }
> } else {
> - if (phy->pmu && data->cfg->enable_pmu_unk1) {
> - val = readl(phy->pmu + REG_PMU_UNK1);
> - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
> - }
> -
> /* Enable USB 45 Ohm resistor calibration */
> if (phy->index == 0)
> sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
> 0x01, 1);
> @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
> sun4i_a10_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
> @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
> sun5i_a13_cfg = {
> .disc_thresh = 2,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
> @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
> sun6i_a31_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
> @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
> sun7i_a20_cfg = {
> .disc_thresh = 2,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = false,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
> @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
> sun8i_a23_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A10,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
> @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
> sun8i_a33_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = false,
> };
>
> static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
> @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_h3_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_r40_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
> sun8i_v3s_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
> sun50i_a64_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> + .pmu_unk1_clrbits = BIT(1),
> .phy0_dual_route = true,
> };
>
> @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
> sun50i_h6_cfg = {
> .disc_thresh = 3,
> .phyctl_offset = REG_PHYCTL_A33,
> .dedicated_clocks = true,
> - .enable_pmu_unk1 = true,
> .phy0_dual_route = true,
> .missing_phys = BIT(1) | BIT(2),
> };
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
2020-12-13 18:24 ` Icenowy Zheng
@ 2020-12-14 1:35 ` André Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: André Przywara @ 2020-12-14 1:35 UTC (permalink / raw)
To: Icenowy Zheng, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
On 13/12/2020 18:24, Icenowy Zheng wrote:
> 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
>> Newer SoCs (A100, H616) need to clear a different bit in our
>> "unknown"
>> PMU PHY register.
>
> It looks like that the unknown PHY register is PHYCTL register for each
> individual PHY, and the bit that is cleared is
> called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
> the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
Oh, right, somehow I failed to find this in the BSP, I guess I got
confused over that similar symbol. I will put proper names to it.
Thanks!
Andre
>>
>> Generalise the existing code by allowing configs to specify a bitmask
>> of bits to clear.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> ---
>> drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++------------
>> ----
>> 1 file changed, 11 insertions(+), 17 deletions(-)
>>
>> diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
>> b/drivers/phy/allwinner/phy-sun4i-usb.c
>> index 651d5e2a25ce..4ba0699e0bb4 100644
>> --- a/drivers/phy/allwinner/phy-sun4i-usb.c
>> +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
>> @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
>> int hsic_index;
>> enum sun4i_usb_phy_type type;
>> u32 disc_thresh;
>> + u32 pmu_unk1_clrbits;
>> u8 phyctl_offset;
>> bool dedicated_clocks;
>> - bool enable_pmu_unk1;
>> bool phy0_dual_route;
>> int missing_phys;
>> };
>> @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
>> return ret;
>> }
>>
>> + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
>> + val = readl(phy->pmu + REG_PMU_UNK1);
>> + val &= ~data->cfg->pmu_unk1_clrbits;
>> + writel(val, phy->pmu + REG_PMU_UNK1);
>> + }
>> +
>> if (data->cfg->type == sun8i_a83t_phy ||
>> data->cfg->type == sun50i_h6_phy) {
>> if (phy->index == 0) {
>> @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
>> writel(val, data->base + data->cfg-
>>> phyctl_offset);
>> }
>> } else {
>> - if (phy->pmu && data->cfg->enable_pmu_unk1) {
>> - val = readl(phy->pmu + REG_PMU_UNK1);
>> - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
>> - }
>> -
>> /* Enable USB 45 Ohm resistor calibration */
>> if (phy->index == 0)
>> sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
>> 0x01, 1);
>> @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
>> sun4i_a10_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
>> @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
>> sun5i_a13_cfg = {
>> .disc_thresh = 2,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
>> @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
>> sun6i_a31_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
>> @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
>> sun7i_a20_cfg = {
>> .disc_thresh = 2,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
>> @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_a23_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
>> @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_a33_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
>> @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_h3_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_r40_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_v3s_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
>> sun50i_a64_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
>> sun50i_h6_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> .phy0_dual_route = true,
>> .missing_phys = BIT(1) | BIT(2),
>> };
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
@ 2020-12-14 1:35 ` André Przywara
0 siblings, 0 replies; 98+ messages in thread
From: André Przywara @ 2020-12-14 1:35 UTC (permalink / raw)
To: Icenowy Zheng, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Vinod Koul, Yangtao Li, Linus Walleij, linux-kernel,
Kishon Vijay Abraham I, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
On 13/12/2020 18:24, Icenowy Zheng wrote:
> 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
>> Newer SoCs (A100, H616) need to clear a different bit in our
>> "unknown"
>> PMU PHY register.
>
> It looks like that the unknown PHY register is PHYCTL register for each
> individual PHY, and the bit that is cleared is
> called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
> the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
Oh, right, somehow I failed to find this in the BSP, I guess I got
confused over that similar symbol. I will put proper names to it.
Thanks!
Andre
>>
>> Generalise the existing code by allowing configs to specify a bitmask
>> of bits to clear.
>>
>> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
>> ---
>> drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++------------
>> ----
>> 1 file changed, 11 insertions(+), 17 deletions(-)
>>
>> diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
>> b/drivers/phy/allwinner/phy-sun4i-usb.c
>> index 651d5e2a25ce..4ba0699e0bb4 100644
>> --- a/drivers/phy/allwinner/phy-sun4i-usb.c
>> +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
>> @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
>> int hsic_index;
>> enum sun4i_usb_phy_type type;
>> u32 disc_thresh;
>> + u32 pmu_unk1_clrbits;
>> u8 phyctl_offset;
>> bool dedicated_clocks;
>> - bool enable_pmu_unk1;
>> bool phy0_dual_route;
>> int missing_phys;
>> };
>> @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy *_phy)
>> return ret;
>> }
>>
>> + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
>> + val = readl(phy->pmu + REG_PMU_UNK1);
>> + val &= ~data->cfg->pmu_unk1_clrbits;
>> + writel(val, phy->pmu + REG_PMU_UNK1);
>> + }
>> +
>> if (data->cfg->type == sun8i_a83t_phy ||
>> data->cfg->type == sun50i_h6_phy) {
>> if (phy->index == 0) {
>> @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy *_phy)
>> writel(val, data->base + data->cfg-
>>> phyctl_offset);
>> }
>> } else {
>> - if (phy->pmu && data->cfg->enable_pmu_unk1) {
>> - val = readl(phy->pmu + REG_PMU_UNK1);
>> - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
>> - }
>> -
>> /* Enable USB 45 Ohm resistor calibration */
>> if (phy->index == 0)
>> sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
>> 0x01, 1);
>> @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
>> sun4i_a10_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
>> @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
>> sun5i_a13_cfg = {
>> .disc_thresh = 2,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
>> @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
>> sun6i_a31_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
>> @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
>> sun7i_a20_cfg = {
>> .disc_thresh = 2,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = false,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
>> @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_a23_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A10,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
>> @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_a33_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = false,
>> };
>>
>> static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
>> @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_h3_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_r40_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
>> sun8i_v3s_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
>> sun50i_a64_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> + .pmu_unk1_clrbits = BIT(1),
>> .phy0_dual_route = true,
>> };
>>
>> @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
>> sun50i_h6_cfg = {
>> .disc_thresh = 3,
>> .phyctl_offset = REG_PHYCTL_A33,
>> .dedicated_clocks = true,
>> - .enable_pmu_unk1 = true,
>> .phy0_dual_route = true,
>> .missing_phys = BIT(1) | BIT(2),
>> };
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
2020-12-14 1:35 ` André Przywara
@ 2020-12-14 4:45 ` Icenowy Zheng
-1 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-14 4:45 UTC (permalink / raw)
To: André Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
在 2020-12-14星期一的 01:35 +0000，André Przywara写道：
> On 13/12/2020 18:24, Icenowy Zheng wrote:
> > 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> > > Newer SoCs (A100, H616) need to clear a different bit in our
> > > "unknown"
> > > PMU PHY register.
> >
> > It looks like that the unknown PHY register is PHYCTL register for
> > each
> > individual PHY, and the bit that is cleared is
> > called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
> > the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
In addition, both the BIT(1) in old PHYs and the BIT(3) in new PHYs are
SIDDQ. (In BSP it's a #define inside #if)
Should we add some flag for 28nm PHY?
>
> Oh, right, somehow I failed to find this in the BSP, I guess I got
> confused over that similar symbol. I will put proper names to it.
In addition, the region at 0x800 is not PMU at all, but some [OE]HCI-
related control registers. The name "PMU" can only cover the first
register here.
We may need to address this.
>
> Thanks!
> Andre
>
> > > Generalise the existing code by allowing configs to specify a
> > > bitmask
> > > of bits to clear.
> > >
> > > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > > ---
> > > drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++--------
> > > ----
> > > ----
> > > 1 file changed, 11 insertions(+), 17 deletions(-)
> > >
> > > diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
> > > b/drivers/phy/allwinner/phy-sun4i-usb.c
> > > index 651d5e2a25ce..4ba0699e0bb4 100644
> > > --- a/drivers/phy/allwinner/phy-sun4i-usb.c
> > > +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
> > > @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
> > > int hsic_index;
> > > enum sun4i_usb_phy_type type;
> > > u32 disc_thresh;
> > > + u32 pmu_unk1_clrbits;
> > > u8 phyctl_offset;
> > > bool dedicated_clocks;
> > > - bool enable_pmu_unk1;
> > > bool phy0_dual_route;
> > > int missing_phys;
> > > };
> > > @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy
> > > *_phy)
> > > return ret;
> > > }
> > >
> > > + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
> > > + val = readl(phy->pmu + REG_PMU_UNK1);
> > > + val &= ~data->cfg->pmu_unk1_clrbits;
> > > + writel(val, phy->pmu + REG_PMU_UNK1);
> > > + }
> > > +
> > > if (data->cfg->type == sun8i_a83t_phy ||
> > > data->cfg->type == sun50i_h6_phy) {
> > > if (phy->index == 0) {
> > > @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy
> > > *_phy)
> > > writel(val, data->base + data->cfg-
> > > > phyctl_offset);
> > > }
> > > } else {
> > > - if (phy->pmu && data->cfg->enable_pmu_unk1) {
> > > - val = readl(phy->pmu + REG_PMU_UNK1);
> > > - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
> > > - }
> > > -
> > > /* Enable USB 45 Ohm resistor calibration */
> > > if (phy->index == 0)
> > > sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
> > > 0x01, 1);
> > > @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun4i_a10_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
> > > @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun5i_a13_cfg = {
> > > .disc_thresh = 2,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
> > > @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun6i_a31_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
> > > @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun7i_a20_cfg = {
> > > .disc_thresh = 2,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
> > > @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_a23_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
> > > @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_a33_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
> > > @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_h3_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_r40_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_v3s_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun50i_a64_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun50i_h6_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > .phy0_dual_route = true,
> > > .missing_phys = BIT(1) | BIT(2),
> > > };
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 14/21] phy: sun4i-usb: Rework "pmu_unk1" handling
@ 2020-12-14 4:45 ` Icenowy Zheng
0 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-14 4:45 UTC (permalink / raw)
To: André Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Vinod Koul, Yangtao Li, Linus Walleij, linux-kernel,
Kishon Vijay Abraham I, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
在 2020-12-14星期一的 01:35 +0000，André Przywara写道：
> On 13/12/2020 18:24, Icenowy Zheng wrote:
> > 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> > > Newer SoCs (A100, H616) need to clear a different bit in our
> > > "unknown"
> > > PMU PHY register.
> >
> > It looks like that the unknown PHY register is PHYCTL register for
> > each
> > individual PHY, and the bit that is cleared is
> > called SUNXI_HCI_PHY_CTRL_SIDDQ in the BSP (similar to
> > the USBC_PHY_CTL_SIDDQ we cleared for main PHYCTL).
In addition, both the BIT(1) in old PHYs and the BIT(3) in new PHYs are
SIDDQ. (In BSP it's a #define inside #if)
Should we add some flag for 28nm PHY?
>
> Oh, right, somehow I failed to find this in the BSP, I guess I got
> confused over that similar symbol. I will put proper names to it.
In addition, the region at 0x800 is not PMU at all, but some [OE]HCI-
related control registers. The name "PMU" can only cover the first
register here.
We may need to address this.
>
> Thanks!
> Andre
>
> > > Generalise the existing code by allowing configs to specify a
> > > bitmask
> > > of bits to clear.
> > >
> > > Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> > > ---
> > > drivers/phy/allwinner/phy-sun4i-usb.c | 28 +++++++++++--------
> > > ----
> > > ----
> > > 1 file changed, 11 insertions(+), 17 deletions(-)
> > >
> > > diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c
> > > b/drivers/phy/allwinner/phy-sun4i-usb.c
> > > index 651d5e2a25ce..4ba0699e0bb4 100644
> > > --- a/drivers/phy/allwinner/phy-sun4i-usb.c
> > > +++ b/drivers/phy/allwinner/phy-sun4i-usb.c
> > > @@ -115,9 +115,9 @@ struct sun4i_usb_phy_cfg {
> > > int hsic_index;
> > > enum sun4i_usb_phy_type type;
> > > u32 disc_thresh;
> > > + u32 pmu_unk1_clrbits;
> > > u8 phyctl_offset;
> > > bool dedicated_clocks;
> > > - bool enable_pmu_unk1;
> > > bool phy0_dual_route;
> > > int missing_phys;
> > > };
> > > @@ -288,6 +288,12 @@ static int sun4i_usb_phy_init(struct phy
> > > *_phy)
> > > return ret;
> > > }
> > >
> > > + if (phy->pmu && data->cfg->pmu_unk1_clrbits) {
> > > + val = readl(phy->pmu + REG_PMU_UNK1);
> > > + val &= ~data->cfg->pmu_unk1_clrbits;
> > > + writel(val, phy->pmu + REG_PMU_UNK1);
> > > + }
> > > +
> > > if (data->cfg->type == sun8i_a83t_phy ||
> > > data->cfg->type == sun50i_h6_phy) {
> > > if (phy->index == 0) {
> > > @@ -297,11 +303,6 @@ static int sun4i_usb_phy_init(struct phy
> > > *_phy)
> > > writel(val, data->base + data->cfg-
> > > > phyctl_offset);
> > > }
> > > } else {
> > > - if (phy->pmu && data->cfg->enable_pmu_unk1) {
> > > - val = readl(phy->pmu + REG_PMU_UNK1);
> > > - writel(val & ~2, phy->pmu + REG_PMU_UNK1);
> > > - }
> > > -
> > > /* Enable USB 45 Ohm resistor calibration */
> > > if (phy->index == 0)
> > > sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN,
> > > 0x01, 1);
> > > @@ -867,7 +868,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun4i_a10_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun5i_a13_cfg = {
> > > @@ -876,7 +876,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun5i_a13_cfg = {
> > > .disc_thresh = 2,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun6i_a31_cfg = {
> > > @@ -885,7 +884,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun6i_a31_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun7i_a20_cfg = {
> > > @@ -894,7 +892,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun7i_a20_cfg = {
> > > .disc_thresh = 2,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = false,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a23_cfg = {
> > > @@ -903,7 +900,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_a23_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A10,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
> > > @@ -912,7 +908,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_a33_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = false,
> > > };
> > >
> > > static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
> > > @@ -929,7 +924,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_h3_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -939,7 +934,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_r40_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -949,7 +944,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun8i_v3s_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -959,7 +954,7 @@ static const struct sun4i_usb_phy_cfg
> > > sun50i_a64_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > + .pmu_unk1_clrbits = BIT(1),
> > > .phy0_dual_route = true,
> > > };
> > >
> > > @@ -969,7 +964,6 @@ static const struct sun4i_usb_phy_cfg
> > > sun50i_h6_cfg = {
> > > .disc_thresh = 3,
> > > .phyctl_offset = REG_PHYCTL_A33,
> > > .dedicated_clocks = true,
> > > - .enable_pmu_unk1 = true,
> > > .phy0_dual_route = true,
> > > .missing_phys = BIT(1) | BIT(2),
> > > };
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 15/21] phy: sun4i-usb: Add support for the H616 USB PHY
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
The USB PHY used in the Allwinner H616 SoC inherits some traits from its
various predecessors: it has four full PHYs like the H3, needs some
extra bits to be set like the H6, and clears a different bit in the
PMU_UNK1 register like the A100.
Name all those properties in a new config struct and assign a new
compatible name to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/phy/allwinner/phy-sun4i-usb.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 4ba0699e0bb4..671c5cc59433 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -968,6 +968,16 @@ static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = {
.missing_phys = BIT(1) | BIT(2),
};
+static const struct sun4i_usb_phy_cfg sun50i_h616_cfg = {
+ .num_phys = 4,
+ .type = sun50i_h6_phy,
+ .disc_thresh = 3,
+ .phyctl_offset = REG_PHYCTL_A33,
+ .dedicated_clocks = true,
+ .phy0_dual_route = true,
+ .pmu_unk1_clrbits = BIT(3),
+};
+
static const struct of_device_id sun4i_usb_phy_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg },
{ .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg },
@@ -982,6 +992,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
{ .compatible = "allwinner,sun50i-a64-usb-phy",
.data = &sun50i_a64_cfg},
{ .compatible = "allwinner,sun50i-h6-usb-phy", .data = &sun50i_h6_cfg },
+ { .compatible = "allwinner,sun50i-h616-usb-phy", .data = &sun50i_h616_cfg },
{ },
};
MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 15/21] phy: sun4i-usb: Add support for the H616 USB PHY
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Vinod Koul, Yangtao Li, Linus Walleij, linux-kernel,
Kishon Vijay Abraham I, linux-sunxi, Clément Péron,
Icenowy Zheng, Shuosheng Huang, linux-arm-kernel
The USB PHY used in the Allwinner H616 SoC inherits some traits from its
various predecessors: it has four full PHYs like the H3, needs some
extra bits to be set like the H6, and clears a different bit in the
PMU_UNK1 register like the A100.
Name all those properties in a new config struct and assign a new
compatible name to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/phy/allwinner/phy-sun4i-usb.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/phy/allwinner/phy-sun4i-usb.c b/drivers/phy/allwinner/phy-sun4i-usb.c
index 4ba0699e0bb4..671c5cc59433 100644
--- a/drivers/phy/allwinner/phy-sun4i-usb.c
+++ b/drivers/phy/allwinner/phy-sun4i-usb.c
@@ -968,6 +968,16 @@ static const struct sun4i_usb_phy_cfg sun50i_h6_cfg = {
.missing_phys = BIT(1) | BIT(2),
};
+static const struct sun4i_usb_phy_cfg sun50i_h616_cfg = {
+ .num_phys = 4,
+ .type = sun50i_h6_phy,
+ .disc_thresh = 3,
+ .phyctl_offset = REG_PHYCTL_A33,
+ .dedicated_clocks = true,
+ .phy0_dual_route = true,
+ .pmu_unk1_clrbits = BIT(3),
+};
+
static const struct of_device_id sun4i_usb_phy_of_match[] = {
{ .compatible = "allwinner,sun4i-a10-usb-phy", .data = &sun4i_a10_cfg },
{ .compatible = "allwinner,sun5i-a13-usb-phy", .data = &sun5i_a13_cfg },
@@ -982,6 +992,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
{ .compatible = "allwinner,sun50i-a64-usb-phy",
.data = &sun50i_a64_cfg},
{ .compatible = "allwinner,sun50i-h6-usb-phy", .data = &sun50i_h6_cfg },
+ { .compatible = "allwinner,sun50i-h616-usb-phy", .data = &sun50i_h616_cfg },
{ },
};
MODULE_DEVICE_TABLE(of, sun4i_usb_phy_of_match);
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 15/21] phy: sun4i-usb: Add support for the H616 USB PHY
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 9:52 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:52 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
Kishon Vijay Abraham I, Vinod Koul
[-- Attachment #1: Type: text/plain, Size: 544 bytes --]
On Fri, Dec 11, 2020 at 01:19:28AM +0000, Andre Przywara wrote:
> The USB PHY used in the Allwinner H616 SoC inherits some traits from its
> various predecessors: it has four full PHYs like the H3, needs some
> extra bits to be set like the H6, and clears a different bit in the
> PMU_UNK1 register like the A100.
>
> Name all those properties in a new config struct and assign a new
> compatible name to it.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It looks like you forgot the binding for that one?
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 15/21] phy: sun4i-usb: Add support for the H616 USB PHY
@ 2020-12-14 9:52 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:52 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, Vinod Koul, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Kishon Vijay Abraham I,
Chen-Yu Tsai, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 544 bytes --]
On Fri, Dec 11, 2020 at 01:19:28AM +0000, Andre Przywara wrote:
> The USB PHY used in the Allwinner H616 SoC inherits some traits from its
> various predecessors: it has four full PHYs like the H3, needs some
> extra bits to be set like the H6, and clears a different bit in the
> PMU_UNK1 register like the A100.
>
> Name all those properties in a new config struct and assign a new
> compatible name to it.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It looks like you forgot the binding for that one?
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 16/21] dt-bindings: watchdog: sun4i: Add A100 compatible
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Wim Van Sebroeck,
Guenter Roeck, linux-watchdog, devicetree
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's watchdog controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
index e8f226376108..5ac607de8be4 100644
--- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
@@ -21,6 +21,9 @@ properties:
- items:
- const: allwinner,sun50i-a64-wdt
- const: allwinner,sun6i-a31-wdt
+ - items:
+ - const: allwinner,sun50i-a100-wdt
+ - const: allwinner,sun6i-a31-wdt
- items:
- const: allwinner,sun50i-h6-wdt
- const: allwinner,sun6i-a31-wdt
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 16/21] dt-bindings: watchdog: sun4i: Add A100 compatible
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, linux-watchdog, devicetree, Yangtao Li,
Linus Walleij, Guenter Roeck, linux-kernel, linux-sunxi,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
Wim Van Sebroeck, linux-arm-kernel
From: Yangtao Li <frank@allwinnertech.com>
Add a binding for A100's watchdog controller.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 3 +++
1 file changed, 3 insertions(+)
diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
index e8f226376108..5ac607de8be4 100644
--- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
@@ -21,6 +21,9 @@ properties:
- items:
- const: allwinner,sun50i-a64-wdt
- const: allwinner,sun6i-a31-wdt
+ - items:
+ - const: allwinner,sun50i-a100-wdt
+ - const: allwinner,sun6i-a31-wdt
- items:
- const: allwinner,sun50i-h6-wdt
- const: allwinner,sun6i-a31-wdt
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 16/21] dt-bindings: watchdog: sun4i: Add A100 compatible
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-13 16:12 ` Guenter Roeck
-1 siblings, 0 replies; 98+ messages in thread
From: Guenter Roeck @ 2020-12-13 16:12 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, linux-arm-kernel, linux-kernel,
linux-sunxi, Wim Van Sebroeck, linux-watchdog, devicetree
On Fri, Dec 11, 2020 at 01:19:29AM +0000, Andre Przywara wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's watchdog controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> index e8f226376108..5ac607de8be4 100644
> --- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> @@ -21,6 +21,9 @@ properties:
> - items:
> - const: allwinner,sun50i-a64-wdt
> - const: allwinner,sun6i-a31-wdt
> + - items:
> + - const: allwinner,sun50i-a100-wdt
> + - const: allwinner,sun6i-a31-wdt
> - items:
> - const: allwinner,sun50i-h6-wdt
> - const: allwinner,sun6i-a31-wdt
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 16/21] dt-bindings: watchdog: sun4i: Add A100 compatible
@ 2020-12-13 16:12 ` Guenter Roeck
0 siblings, 0 replies; 98+ messages in thread
From: Guenter Roeck @ 2020-12-13 16:12 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, linux-watchdog, devicetree,
Yangtao Li, Linus Walleij, linux-sunxi, linux-kernel,
Maxime Ripard, Chen-Yu Tsai, Clément Péron,
Icenowy Zheng, Shuosheng Huang, Wim Van Sebroeck,
linux-arm-kernel
On Fri, Dec 11, 2020 at 01:19:29AM +0000, Andre Przywara wrote:
> From: Yangtao Li <frank@allwinnertech.com>
>
> Add a binding for A100's watchdog controller.
>
> Signed-off-by: Yangtao Li <frank@allwinnertech.com>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> index e8f226376108..5ac607de8be4 100644
> --- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> @@ -21,6 +21,9 @@ properties:
> - items:
> - const: allwinner,sun50i-a64-wdt
> - const: allwinner,sun6i-a31-wdt
> + - items:
> + - const: allwinner,sun50i-a100-wdt
> + - const: allwinner,sun6i-a31-wdt
> - items:
> - const: allwinner,sun50i-h6-wdt
> - const: allwinner,sun6i-a31-wdt
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Wim Van Sebroeck,
Guenter Roeck, linux-watchdog, devicetree
Use enums to group all compatible devices together on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
1 file changed, 5 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
index 5ac607de8be4..9aa3c313c49f 100644
--- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
@@ -19,13 +19,11 @@ properties:
- const: allwinner,sun4i-a10-wdt
- const: allwinner,sun6i-a31-wdt
- items:
- - const: allwinner,sun50i-a64-wdt
- - const: allwinner,sun6i-a31-wdt
- - items:
- - const: allwinner,sun50i-a100-wdt
- - const: allwinner,sun6i-a31-wdt
- - items:
- - const: allwinner,sun50i-h6-wdt
+ - enum:
+ - allwinner,sun50i-a64-wdt
+ - allwinner,sun50i-a100-wdt
+ - allwinner,sun50i-h6-wdt
+ - allwinner,sun50i-h616-wdt
- const: allwinner,sun6i-a31-wdt
- items:
- const: allwinner,suniv-f1c100s-wdt
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, linux-watchdog, devicetree, Yangtao Li,
Linus Walleij, Guenter Roeck, linux-kernel, linux-sunxi,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
Wim Van Sebroeck, linux-arm-kernel
Use enums to group all compatible devices together on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
1 file changed, 5 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
index 5ac607de8be4..9aa3c313c49f 100644
--- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
@@ -19,13 +19,11 @@ properties:
- const: allwinner,sun4i-a10-wdt
- const: allwinner,sun6i-a31-wdt
- items:
- - const: allwinner,sun50i-a64-wdt
- - const: allwinner,sun6i-a31-wdt
- - items:
- - const: allwinner,sun50i-a100-wdt
- - const: allwinner,sun6i-a31-wdt
- - items:
- - const: allwinner,sun50i-h6-wdt
+ - enum:
+ - allwinner,sun50i-a64-wdt
+ - allwinner,sun50i-a100-wdt
+ - allwinner,sun50i-h6-wdt
+ - allwinner,sun50i-h616-wdt
- const: allwinner,sun6i-a31-wdt
- items:
- const: allwinner,suniv-f1c100s-wdt
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:55 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:55 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Maxime Ripard, Icenowy Zheng, linux-sunxi,
Shuosheng Huang, Guenter Roeck, devicetree, linux-watchdog,
Linus Walleij, linux-kernel, linux-arm-kernel, Wim Van Sebroeck,
Jernej Skrabec, Yangtao Li, Clément Péron
On Fri, 11 Dec 2020 01:19:30 +0000, Andre Przywara wrote:
> Use enums to group all compatible devices together on the way.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
> 1 file changed, 5 insertions(+), 7 deletions(-)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
@ 2020-12-14 22:55 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:55 UTC (permalink / raw)
To: Andre Przywara
Cc: linux-arm-kernel, devicetree, Jernej Skrabec, linux-watchdog,
Yangtao Li, Linus Walleij, linux-sunxi, Maxime Ripard,
linux-kernel, Chen-Yu Tsai, Shuosheng Huang, Icenowy Zheng,
Clément Péron, Wim Van Sebroeck, Guenter Roeck
On Fri, 11 Dec 2020 01:19:30 +0000, Andre Przywara wrote:
> Use enums to group all compatible devices together on the way.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
> 1 file changed, 5 insertions(+), 7 deletions(-)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
2020-12-11 1:19 ` Andre Przywara
@ 2021-01-23 17:29 ` Guenter Roeck
-1 siblings, 0 replies; 98+ messages in thread
From: Guenter Roeck @ 2021-01-23 17:29 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, linux-arm-kernel, linux-kernel,
linux-sunxi, Wim Van Sebroeck, linux-watchdog, devicetree
On Fri, Dec 11, 2020 at 01:19:30AM +0000, Andre Przywara wrote:
> Use enums to group all compatible devices together on the way.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
> 1 file changed, 5 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> index 5ac607de8be4..9aa3c313c49f 100644
> --- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> @@ -19,13 +19,11 @@ properties:
> - const: allwinner,sun4i-a10-wdt
> - const: allwinner,sun6i-a31-wdt
> - items:
> - - const: allwinner,sun50i-a64-wdt
> - - const: allwinner,sun6i-a31-wdt
> - - items:
> - - const: allwinner,sun50i-a100-wdt
> - - const: allwinner,sun6i-a31-wdt
> - - items:
> - - const: allwinner,sun50i-h6-wdt
> + - enum:
> + - allwinner,sun50i-a64-wdt
> + - allwinner,sun50i-a100-wdt
> + - allwinner,sun50i-h6-wdt
> + - allwinner,sun50i-h616-wdt
> - const: allwinner,sun6i-a31-wdt
> - items:
> - const: allwinner,suniv-f1c100s-wdt
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 17/21] dt-bindings: watchdog: sun4i: Add H616 compatible string
@ 2021-01-23 17:29 ` Guenter Roeck
0 siblings, 0 replies; 98+ messages in thread
From: Guenter Roeck @ 2021-01-23 17:29 UTC (permalink / raw)
To: Andre Przywara
Cc: Jernej Skrabec, linux-watchdog, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Maxime Ripard,
Chen-Yu Tsai, Clément Péron, Icenowy Zheng,
Shuosheng Huang, Wim Van Sebroeck, linux-arm-kernel
On Fri, Dec 11, 2020 at 01:19:30AM +0000, Andre Przywara wrote:
> Use enums to group all compatible devices together on the way.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
> ---
> .../bindings/watchdog/allwinner,sun4i-a10-wdt.yaml | 12 +++++-------
> 1 file changed, 5 insertions(+), 7 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> index 5ac607de8be4..9aa3c313c49f 100644
> --- a/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> +++ b/Documentation/devicetree/bindings/watchdog/allwinner,sun4i-a10-wdt.yaml
> @@ -19,13 +19,11 @@ properties:
> - const: allwinner,sun4i-a10-wdt
> - const: allwinner,sun6i-a31-wdt
> - items:
> - - const: allwinner,sun50i-a64-wdt
> - - const: allwinner,sun6i-a31-wdt
> - - items:
> - - const: allwinner,sun50i-a100-wdt
> - - const: allwinner,sun6i-a31-wdt
> - - items:
> - - const: allwinner,sun50i-h6-wdt
> + - enum:
> + - allwinner,sun50i-a64-wdt
> + - allwinner,sun50i-a100-wdt
> + - allwinner,sun50i-h6-wdt
> + - allwinner,sun50i-h616-wdt
> - const: allwinner,sun6i-a31-wdt
> - items:
> - const: allwinner,suniv-f1c100s-wdt
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Gregory CLEMENT,
Mauro Carvalho Chehab, Alessandro Zummo, Alexandre Belloni,
Mark Brown, linux-i2c, linux-media, linux-rtc, linux-spi,
devicetree
Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
bindings, and pair them with an existing fallback compatible string,
as the devices are compatible.
This covers I2C, infrared, RTC and SPI.
Use enums to group all compatible devices together.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +++++++------------
.../media/allwinner,sun4i-a10-ir.yaml | 16 ++++++--------
.../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +++
.../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
4 files changed, 17 insertions(+), 24 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
index 5b5ae402f97a..eb72dd571def 100644
--- a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
@@ -18,21 +18,14 @@ properties:
- const: allwinner,sun4i-a10-i2c
- const: allwinner,sun6i-a31-i2c
- items:
- - const: allwinner,sun8i-a23-i2c
+ - enum:
+ - allwinner,sun8i-a23-i2c
+ - allwinner,sun8i-a83t-i2c
+ - allwinner,sun50i-a64-i2c
+ - allwinner,sun50i-a100-i2c
+ - allwinner,sun50i-h6-i2c
+ - allwinner,sun50i-h616-i2c
- const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun8i-a83t-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-a64-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-a100-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-h6-i2c
- - const: allwinner,sun6i-a31-i2c
-
- const: marvell,mv64xxx-i2c
- const: marvell,mv78230-i2c
- const: marvell,mv78230-a0-i2c
diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
index 5fa19d4aeaf3..6d8395d6bca0 100644
--- a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
+++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
@@ -20,16 +20,12 @@ properties:
- const: allwinner,sun5i-a13-ir
- const: allwinner,sun6i-a31-ir
- items:
- - const: allwinner,sun8i-a83t-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun8i-r40-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun50i-a64-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun50i-h6-ir
+ - enum:
+ - allwinner,sun8i-a83t-ir
+ - allwinner,sun8i-r40-ir
+ - allwinner,sun50i-a64-ir
+ - allwinner,sun50i-h6-ir
+ - allwinner,sun50i-h616-ir
- const: allwinner,sun6i-a31-ir
reg:
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index 37c2a601c3fa..97928efd2bc9 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -26,6 +26,9 @@ properties:
- const: allwinner,sun50i-a64-rtc
- const: allwinner,sun8i-h3-rtc
- const: allwinner,sun50i-h6-rtc
+ - items:
+ - const: allwinner,sun50i-h616-rtc
+ - const: allwinner,sun50i-h6-rtc
reg:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
index 7866a655d81c..908248260afa 100644
--- a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -25,6 +25,7 @@ properties:
- enum:
- allwinner,sun8i-r40-spi
- allwinner,sun50i-h6-spi
+ - allwinner,sun50i-h616-spi
- const: allwinner,sun8i-h3-spi
reg:
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: linux-rtc, Rob Herring, Alexandre Belloni, linux-media,
Alessandro Zummo, Yangtao Li, Linus Walleij, linux-kernel,
linux-spi, linux-sunxi, Mark Brown, Clément Péron,
Icenowy Zheng, devicetree, Shuosheng Huang,
Mauro Carvalho Chehab, Gregory CLEMENT, linux-arm-kernel,
linux-i2c
Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
bindings, and pair them with an existing fallback compatible string,
as the devices are compatible.
This covers I2C, infrared, RTC and SPI.
Use enums to group all compatible devices together.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +++++++------------
.../media/allwinner,sun4i-a10-ir.yaml | 16 ++++++--------
.../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +++
.../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
4 files changed, 17 insertions(+), 24 deletions(-)
diff --git a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
index 5b5ae402f97a..eb72dd571def 100644
--- a/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
+++ b/Documentation/devicetree/bindings/i2c/marvell,mv64xxx-i2c.yaml
@@ -18,21 +18,14 @@ properties:
- const: allwinner,sun4i-a10-i2c
- const: allwinner,sun6i-a31-i2c
- items:
- - const: allwinner,sun8i-a23-i2c
+ - enum:
+ - allwinner,sun8i-a23-i2c
+ - allwinner,sun8i-a83t-i2c
+ - allwinner,sun50i-a64-i2c
+ - allwinner,sun50i-a100-i2c
+ - allwinner,sun50i-h6-i2c
+ - allwinner,sun50i-h616-i2c
- const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun8i-a83t-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-a64-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-a100-i2c
- - const: allwinner,sun6i-a31-i2c
- - items:
- - const: allwinner,sun50i-h6-i2c
- - const: allwinner,sun6i-a31-i2c
-
- const: marvell,mv64xxx-i2c
- const: marvell,mv78230-i2c
- const: marvell,mv78230-a0-i2c
diff --git a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
index 5fa19d4aeaf3..6d8395d6bca0 100644
--- a/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
+++ b/Documentation/devicetree/bindings/media/allwinner,sun4i-a10-ir.yaml
@@ -20,16 +20,12 @@ properties:
- const: allwinner,sun5i-a13-ir
- const: allwinner,sun6i-a31-ir
- items:
- - const: allwinner,sun8i-a83t-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun8i-r40-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun50i-a64-ir
- - const: allwinner,sun6i-a31-ir
- - items:
- - const: allwinner,sun50i-h6-ir
+ - enum:
+ - allwinner,sun8i-a83t-ir
+ - allwinner,sun8i-r40-ir
+ - allwinner,sun50i-a64-ir
+ - allwinner,sun50i-h6-ir
+ - allwinner,sun50i-h616-ir
- const: allwinner,sun6i-a31-ir
reg:
diff --git a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
index 37c2a601c3fa..97928efd2bc9 100644
--- a/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
+++ b/Documentation/devicetree/bindings/rtc/allwinner,sun6i-a31-rtc.yaml
@@ -26,6 +26,9 @@ properties:
- const: allwinner,sun50i-a64-rtc
- const: allwinner,sun8i-h3-rtc
- const: allwinner,sun50i-h6-rtc
+ - items:
+ - const: allwinner,sun50i-h616-rtc
+ - const: allwinner,sun50i-h6-rtc
reg:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
index 7866a655d81c..908248260afa 100644
--- a/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/allwinner,sun6i-a31-spi.yaml
@@ -25,6 +25,7 @@ properties:
- enum:
- allwinner,sun8i-r40-spi
- allwinner,sun50i-h6-spi
+ - allwinner,sun50i-h616-spi
- const: allwinner,sun8i-h3-spi
reg:
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:56 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:56 UTC (permalink / raw)
To: Andre Przywara
Cc: linux-media, linux-rtc, Clément Péron, Linus Walleij,
linux-sunxi, Chen-Yu Tsai, Icenowy Zheng, linux-i2c,
Gregory CLEMENT, devicetree, linux-kernel, Mark Brown,
Maxime Ripard, Mauro Carvalho Chehab, Shuosheng Huang,
Yangtao Li, Alessandro Zummo, linux-arm-kernel, Jernej Skrabec,
linux-spi, Alexandre Belloni
On Fri, 11 Dec 2020 01:19:31 +0000, Andre Przywara wrote:
> Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
> bindings, and pair them with an existing fallback compatible string,
> as the devices are compatible.
> This covers I2C, infrared, RTC and SPI.
>
> Use enums to group all compatible devices together.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +++++++------------
> .../media/allwinner,sun4i-a10-ir.yaml | 16 ++++++--------
> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +++
> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
> 4 files changed, 17 insertions(+), 24 deletions(-)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
@ 2020-12-14 22:56 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:56 UTC (permalink / raw)
To: Andre Przywara
Cc: linux-rtc, devicetree, Jernej Skrabec, Alexandre Belloni,
Alessandro Zummo, Yangtao Li, Linus Walleij, linux-spi,
linux-sunxi, Maxime Ripard, linux-kernel, linux-i2c,
Chen-Yu Tsai, Mark Brown, Clément Péron, Icenowy Zheng,
Shuosheng Huang, Mauro Carvalho Chehab, Gregory CLEMENT,
linux-arm-kernel, linux-media
On Fri, 11 Dec 2020 01:19:31 +0000, Andre Przywara wrote:
> Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
> bindings, and pair them with an existing fallback compatible string,
> as the devices are compatible.
> This covers I2C, infrared, RTC and SPI.
>
> Use enums to group all compatible devices together.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +++++++------------
> .../media/allwinner,sun4i-a10-ir.yaml | 16 ++++++--------
> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +++
> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
> 4 files changed, 17 insertions(+), 24 deletions(-)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
2020-12-11 1:19 ` Andre Przywara
@ 2021-01-05 16:29 ` Wolfram Sang
-1 siblings, 0 replies; 98+ messages in thread
From: Wolfram Sang @ 2021-01-05 16:29 UTC (permalink / raw)
To: Andre Przywara
Cc: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, linux-arm-kernel, linux-kernel,
linux-sunxi, Gregory CLEMENT, Mauro Carvalho Chehab,
Alessandro Zummo, Alexandre Belloni, Mark Brown, linux-i2c,
linux-media, linux-rtc, linux-spi, devicetree
[-- Attachment #1: Type: text/plain, Size: 461 bytes --]
On Fri, Dec 11, 2020 at 01:19:31AM +0000, Andre Przywara wrote:
> Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
> bindings, and pair them with an existing fallback compatible string,
> as the devices are compatible.
> This covers I2C, infrared, RTC and SPI.
>
> Use enums to group all compatible devices together.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 18/21] dt-bindings: allwinner: Add H616 compatible strings
@ 2021-01-05 16:29 ` Wolfram Sang
0 siblings, 0 replies; 98+ messages in thread
From: Wolfram Sang @ 2021-01-05 16:29 UTC (permalink / raw)
To: Andre Przywara
Cc: Alexandre Belloni, Yangtao Li, Linus Walleij, linux-sunxi,
Icenowy Zheng, linux-rtc, Gregory CLEMENT, Chen-Yu Tsai,
Clément Péron, Shuosheng Huang, linux-media,
devicetree, Maxime Ripard, Mark Brown, Mauro Carvalho Chehab,
linux-arm-kernel, Alessandro Zummo, Jernej Skrabec, linux-kernel,
linux-spi, linux-i2c
[-- Attachment #1.1: Type: text/plain, Size: 461 bytes --]
On Fri, Dec 11, 2020 at 01:19:31AM +0000, Andre Przywara wrote:
> Add simple "allwinner,sun50i-h616-xxx" compatible names to existing
> bindings, and pair them with an existing fallback compatible string,
> as the devices are compatible.
> This covers I2C, infrared, RTC and SPI.
>
> Use enums to group all compatible devices together.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, devicetree
This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
There does not seem to be an extra interrupt controller anymore, also
it lacks the corresponding NMI pin, so no interrupts for the PMIC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++++++++++
1 file changed, 715 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..7202632b061b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,715 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 512KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@40000000 {
+ reg = <0x0 0x40000000 0x0 0x80000>;
+ no-map;
+ };
+ };
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ arm,no-tick-in-suspend;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x40000000>;
+
+ syscon: syscon@3000000 {
+ compatible = "allwinner,sun50i-h616-system-control";
+ reg = <0x03000000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@28000 {
+ compatible = "mmio-sram";
+ reg = <0x00028000 0x30000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00028000 0x30000>;
+ };
+ };
+
+ ccu: clock@3001000 {
+ compatible = "allwinner,sun50i-h616-ccu";
+ reg = <0x03001000 0x1000>;
+ clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ watchdog: watchdog@30090a0 {
+ compatible = "allwinner,sun50i-h616-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x030090a0 0x20>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ pio: pinctrl@300b000 {
+ compatible = "allwinner,sun50i-h616-pinctrl";
+ reg = <0x0300b000 0x400>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ext_rgmii_pins: rgmii-pins {
+ pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+ "PI5", "PI7", "PI8", "PI9", "PI10",
+ "PI11", "PI12", "PI13", "PI14", "PI15",
+ "PI16";
+ function = "emac0";
+ drive-strength = <40>;
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PI6", "PI7";
+ function = "i2c0";
+ };
+
+ i2c3_ph_pins: i2c3-ph-pins {
+ pins = "PH4", "PH5";
+ function = "i2c3";
+ };
+
+ ir_rx_pin: ir_rx_pin {
+ pins = "PH10";
+ function = "ir_rx";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_pins: mmc2-pins {
+ pins = "PC0", "PC1", "PC5", "PC6",
+ "PC8", "PC9", "PC10", "PC11",
+ "PC13", "PC14", "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0-pins {
+ pins = "PC0", "PC2", "PC3", "PC4";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1-pins {
+ pins = "PH6", "PH7", "PH8";
+ function = "spi1";
+ };
+
+ spi1_cs_pin: spi1-cs-pin {
+ pins = "PH5";
+ function = "spi1";
+ };
+
+ uart0_ph_pins: uart0-ph-pins {
+ pins = "PH0", "PH1";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+ };
+
+ gic: interrupt-controller@3021000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>,
+ <0x03022000 0x2000>,
+ <0x03024000 0x2000>,
+ <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ mmc0: mmc@4020000 {
+ compatible = "allwinner,sun50i-h616-mmc",
+ "allwinner,sun50i-a100-mmc";
+ reg = <0x04020000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@4021000 {
+ compatible = "allwinner,sun50i-h616-mmc",
+ "allwinner,sun50i-a100-mmc";
+ reg = <0x04021000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@4022000 {
+ compatible = "allwinner,sun50i-h616-emmc",
+ "allwinner,sun50i-a100-emmc";
+ reg = <0x04022000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: serial@5000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@5000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@5000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@5000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@5001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ uart5: serial@5001400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001400 0x400>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@5002000 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002000 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@5002400 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002400 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@5002800 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002800 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@5002c00 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002c00 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c@5003000 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05003000 0x400>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C4>;
+ resets = <&ccu RST_BUS_I2C4>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@5010000 {
+ compatible = "allwinner,sun50i-h616-spi",
+ "allwinner,sun8i-h3-spi";
+ reg = <0x05010000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_SPI0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@5011000 {
+ compatible = "allwinner,sun50i-h616-spi",
+ "allwinner,sun8i-h3-spi";
+ reg = <0x05011000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_SPI1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac0: ethernet@5020000 {
+ compatible = "allwinner,sun50i-h616-emac",
+ "allwinner,sun50i-a64-emac";
+ syscon = <&syscon>;
+ reg = <0x05020000 0x10000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC0>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC0>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ mdio0: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ emac1: ethernet@5030000 {
+ compatible = "allwinner,sun50i-h616-emac";
+ syscon = <&syscon 1>;
+ reg = <0x05030000 0x10000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC1>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC1>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ mdio1: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ usbotg: usb@5100000 {
+ compatible = "allwinner,sun50i-h616-musb",
+ "allwinner,sun8i-h3-musb";
+ reg = <0x05100000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy@5100400 {
+ compatible = "allwinner,sun50i-h616-usb-phy";
+ reg = <0x05100400 0x24>,
+ <0x05101800 0x14>,
+ <0x05200800 0x14>,
+ <0x05310800 0x14>,
+ <0x05311800 0x14>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@5101000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05101000 0x100>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@5101400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05101400 0x100>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@5200000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05200000 0x100>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_BUS_EHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>,
+ <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@5200400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05200400 0x100>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@5310000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05310000 0x100>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_BUS_EHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_OHCI2>,
+ <&ccu RST_BUS_EHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@5310400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05310400 0x100>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb@5311000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05311000 0x100>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_BUS_EHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>,
+ <&ccu RST_BUS_EHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@5311400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05311400 0x100>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ rtc: rtc@7000000 {
+ compatible = "allwinner,sun50i-h616-rtc",
+ "allwinner,sun50i-h6-rtc";
+ reg = <0x07000000 0x400>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "osc32k", "osc32k-out", "iosc";
+ #clock-cells = <1>;
+ };
+
+ r_ccu: clock@7010000 {
+ compatible = "allwinner,sun50i-h616-r-ccu";
+ reg = <0x07010000 0x400>;
+ clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+ <&ccu CLK_PLL_PERIPH0>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ r_pio: pinctrl@7022000 {
+ compatible = "allwinner,sun50i-h616-r-pinctrl";
+ reg = <0x07022000 0x400>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_i2c_pins: r-i2c-pins {
+ pins = "PL0", "PL1";
+ function = "s_i2c";
+ };
+ };
+
+ ir: ir@7040000 {
+ compatible = "allwinner,sun50i-h616-ir",
+ "allwinner,sun6i-a31-ir";
+ reg = <0x07040000 0x400>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1_IR>,
+ <&r_ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ resets = <&r_ccu RST_R_APB1_IR>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_rx_pin>;
+ status = "disabled";
+ };
+
+ r_i2c: i2c@7081400 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081400 0x400>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C>;
+ resets = <&r_ccu RST_R_APB2_I2C>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
There does not seem to be an extra interrupt controller anymore, also
it lacks the corresponding NMI pin, so no interrupts for the PMIC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
.../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++++++++++
1 file changed, 715 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..7202632b061b
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,715 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+// Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu2: cpu@2 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+
+ cpu3: cpu@3 {
+ compatible = "arm,cortex-a53";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ clocks = <&ccu CLK_CPUX>;
+ };
+ };
+
+ reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* 512KiB reserved for ARM Trusted Firmware (BL31) */
+ secmon_reserved: secmon@40000000 {
+ reg = <0x0 0x40000000 0x0 0x80000>;
+ no-map;
+ };
+ };
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ pmu {
+ compatible = "arm,cortex-a53-pmu";
+ interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ arm,no-tick-in-suspend;
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x0 0x0 0x40000000>;
+
+ syscon: syscon@3000000 {
+ compatible = "allwinner,sun50i-h616-system-control";
+ reg = <0x03000000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ sram_c: sram@28000 {
+ compatible = "mmio-sram";
+ reg = <0x00028000 0x30000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x00028000 0x30000>;
+ };
+ };
+
+ ccu: clock@3001000 {
+ compatible = "allwinner,sun50i-h616-ccu";
+ reg = <0x03001000 0x1000>;
+ clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+ clock-names = "hosc", "losc", "iosc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ watchdog: watchdog@30090a0 {
+ compatible = "allwinner,sun50i-h616-wdt",
+ "allwinner,sun6i-a31-wdt";
+ reg = <0x030090a0 0x20>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ status = "disabled";
+ };
+
+ pio: pinctrl@300b000 {
+ compatible = "allwinner,sun50i-h616-pinctrl";
+ reg = <0x0300b000 0x400>;
+ interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ext_rgmii_pins: rgmii-pins {
+ pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+ "PI5", "PI7", "PI8", "PI9", "PI10",
+ "PI11", "PI12", "PI13", "PI14", "PI15",
+ "PI16";
+ function = "emac0";
+ drive-strength = <40>;
+ };
+
+ i2c0_pins: i2c0-pins {
+ pins = "PI6", "PI7";
+ function = "i2c0";
+ };
+
+ i2c3_ph_pins: i2c3-ph-pins {
+ pins = "PH4", "PH5";
+ function = "i2c3";
+ };
+
+ ir_rx_pin: ir_rx_pin {
+ pins = "PH10";
+ function = "ir_rx";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pins: mmc1-pins {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_pins: mmc2-pins {
+ pins = "PC0", "PC1", "PC5", "PC6",
+ "PC8", "PC9", "PC10", "PC11",
+ "PC13", "PC14", "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0-pins {
+ pins = "PC0", "PC2", "PC3", "PC4";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1-pins {
+ pins = "PH6", "PH7", "PH8";
+ function = "spi1";
+ };
+
+ spi1_cs_pin: spi1-cs-pin {
+ pins = "PH5";
+ function = "spi1";
+ };
+
+ uart0_ph_pins: uart0-ph-pins {
+ pins = "PH0", "PH1";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1-pins {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1-rts-cts-pins {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+ };
+
+ gic: interrupt-controller@3021000 {
+ compatible = "arm,gic-400";
+ reg = <0x03021000 0x1000>,
+ <0x03022000 0x2000>,
+ <0x03024000 0x2000>,
+ <0x03026000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+
+ mmc0: mmc@4020000 {
+ compatible = "allwinner,sun50i-h616-mmc",
+ "allwinner,sun50i-a100-mmc";
+ reg = <0x04020000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc@4021000 {
+ compatible = "allwinner,sun50i-h616-mmc",
+ "allwinner,sun50i-a100-mmc";
+ reg = <0x04021000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc@4022000 {
+ compatible = "allwinner,sun50i-h616-emmc",
+ "allwinner,sun50i-a100-emmc";
+ reg = <0x04022000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ uart0: serial@5000000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial@5000400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial@5000800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial@5000c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05000c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial@5001000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001000 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ uart5: serial@5001400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x05001400 0x400>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ status = "disabled";
+ };
+
+ i2c0: i2c@5002000 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002000 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c@5002400 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002400 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c@5002800 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002800 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c@5002c00 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05002c00 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c@5003000 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x05003000 0x400>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C4>;
+ resets = <&ccu RST_BUS_I2C4>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi0: spi@5010000 {
+ compatible = "allwinner,sun50i-h616-spi",
+ "allwinner,sun8i-h3-spi";
+ reg = <0x05010000 0x1000>;
+ interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_SPI0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi@5011000 {
+ compatible = "allwinner,sun50i-h616-spi",
+ "allwinner,sun8i-h3-spi";
+ reg = <0x05011000 0x1000>;
+ interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ resets = <&ccu RST_BUS_SPI1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ emac0: ethernet@5020000 {
+ compatible = "allwinner,sun50i-h616-emac",
+ "allwinner,sun50i-a64-emac";
+ syscon = <&syscon>;
+ reg = <0x05020000 0x10000>;
+ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC0>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC0>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ mdio0: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ emac1: ethernet@5030000 {
+ compatible = "allwinner,sun50i-h616-emac";
+ syscon = <&syscon 1>;
+ reg = <0x05030000 0x10000>;
+ interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ resets = <&ccu RST_BUS_EMAC1>;
+ reset-names = "stmmaceth";
+ clocks = <&ccu CLK_BUS_EMAC1>;
+ clock-names = "stmmaceth";
+ status = "disabled";
+
+ mdio1: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ usbotg: usb@5100000 {
+ compatible = "allwinner,sun50i-h616-musb",
+ "allwinner,sun8i-h3-musb";
+ reg = <0x05100000 0x0400>;
+ clocks = <&ccu CLK_BUS_OTG>;
+ resets = <&ccu RST_BUS_OTG>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "mc";
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ extcon = <&usbphy 0>;
+ status = "disabled";
+ };
+
+ usbphy: phy@5100400 {
+ compatible = "allwinner,sun50i-h616-usb-phy";
+ reg = <0x05100400 0x24>,
+ <0x05101800 0x14>,
+ <0x05200800 0x14>,
+ <0x05310800 0x14>,
+ <0x05311800 0x14>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci0: usb@5101000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05101000 0x100>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_BUS_EHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>,
+ <&ccu RST_BUS_EHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci0: usb@5101400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05101400 0x100>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI0>,
+ <&ccu CLK_USB_OHCI0>;
+ resets = <&ccu RST_BUS_OHCI0>;
+ phys = <&usbphy 0>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci1: usb@5200000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05200000 0x100>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_BUS_EHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>,
+ <&ccu RST_BUS_EHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb@5200400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05200400 0x100>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb@5310000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05310000 0x100>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_BUS_EHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_OHCI2>,
+ <&ccu RST_BUS_EHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb@5310400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05310400 0x100>;
+ interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb@5311000 {
+ compatible = "allwinner,sun50i-h616-ehci",
+ "generic-ehci";
+ reg = <0x05311000 0x100>;
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_BUS_EHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>,
+ <&ccu RST_BUS_EHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb@5311400 {
+ compatible = "allwinner,sun50i-h616-ohci",
+ "generic-ohci";
+ reg = <0x05311400 0x100>;
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ rtc: rtc@7000000 {
+ compatible = "allwinner,sun50i-h616-rtc",
+ "allwinner,sun50i-h6-rtc";
+ reg = <0x07000000 0x400>;
+ interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clock-output-names = "osc32k", "osc32k-out", "iosc";
+ #clock-cells = <1>;
+ };
+
+ r_ccu: clock@7010000 {
+ compatible = "allwinner,sun50i-h616-r-ccu";
+ reg = <0x07010000 0x400>;
+ clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+ <&ccu CLK_PLL_PERIPH0>;
+ clock-names = "hosc", "losc", "iosc", "pll-periph";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ r_pio: pinctrl@7022000 {
+ compatible = "allwinner,sun50i-h616-r-pinctrl";
+ reg = <0x07022000 0x400>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ r_i2c_pins: r-i2c-pins {
+ pins = "PL0", "PL1";
+ function = "s_i2c";
+ };
+ };
+
+ ir: ir@7040000 {
+ compatible = "allwinner,sun50i-h616-ir",
+ "allwinner,sun6i-a31-ir";
+ reg = <0x07040000 0x400>;
+ interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB1_IR>,
+ <&r_ccu CLK_IR>;
+ clock-names = "apb", "ir";
+ resets = <&r_ccu RST_R_APB1_IR>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_rx_pin>;
+ status = "disabled";
+ };
+
+ r_i2c: i2c@7081400 {
+ compatible = "allwinner,sun50i-h616-i2c",
+ "allwinner,sun6i-a31-i2c";
+ reg = <0x07081400 0x400>;
+ interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&r_ccu CLK_R_APB2_I2C>;
+ resets = <&r_ccu RST_R_APB2_I2C>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+};
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 9:58 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:58 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree
[-- Attachment #1: Type: text/plain, Size: 1069 bytes --]
On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */
> + secmon_reserved: secmon@40000000 {
> + reg = <0x0 0x40000000 0x0 0x80000>;
> + no-map;
> + };
> + };
This should still be set by the firmware
> + mmc0: mmc@4020000 {
> + compatible = "allwinner,sun50i-h616-mmc",
> + "allwinner,sun50i-a100-mmc";
> + reg = <0x04020000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC0>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
Somewhat related: we shouldn't set the MMC speed flags in the drivers.
This is biting us on the already supported SoCs, so it would be great to
not repeat the same mistake with the new ones
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-14 9:58 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:58 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1069 bytes --]
On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */
> + secmon_reserved: secmon@40000000 {
> + reg = <0x0 0x40000000 0x0 0x80000>;
> + no-map;
> + };
> + };
This should still be set by the firmware
> + mmc0: mmc@4020000 {
> + compatible = "allwinner,sun50i-h616-mmc",
> + "allwinner,sun50i-a100-mmc";
> + reg = <0x04020000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC0>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
Somewhat related: we shouldn't set the MMC speed flags in the drivers.
This is biting us on the already supported SoCs, so it would be great to
not repeat the same mistake with the new ones
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-14 9:58 ` Maxime Ripard
@ 2020-12-14 12:53 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-14 12:53 UTC (permalink / raw)
To: Maxime Ripard
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree
On Mon, 14 Dec 2020 10:58:31 +0100
Maxime Ripard <maxime@cerno.tech> wrote:
Hi,
> On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > */
> > + secmon_reserved: secmon@40000000 {
> > + reg = <0x0 0x40000000 0x0 0x80000>;
> > + no-map;
> > + };
> > + };
>
> This should still be set by the firmware
>
> > + mmc0: mmc@4020000 {
> > + compatible = "allwinner,sun50i-h616-mmc",
> > + "allwinner,sun50i-a100-mmc";
> > + reg = <0x04020000 0x1000>;
> > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > CLK_MMC0>;
> > + clock-names = "ahb", "mmc";
> > + resets = <&ccu RST_BUS_MMC0>;
> > + reset-names = "ahb";
> > + interrupts = <GIC_SPI 35
> > IRQ_TYPE_LEVEL_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_pins>;
> > + status = "disabled";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
>
> Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> This is biting us on the already supported SoCs, so it would be great
> to not repeat the same mistake with the new ones
Do you mean to list the "sd-uhs-sdr50" and friends properties here in
the DT?
What is the best practice here in terms putting them in the .dts vs.
the .dtsi? Surely the controller has limits, but bad traces on a board
could impose further restrictions, right?
Though that's probably rare, so it sounds like a lot of churn to list
them in every board DT. So can we list everything in here (.dtsi), then
delete in those affected boards only?
Cheers,
Andre
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-14 12:53 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-14 12:53 UTC (permalink / raw)
To: Maxime Ripard
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
On Mon, 14 Dec 2020 10:58:31 +0100
Maxime Ripard <maxime@cerno.tech> wrote:
Hi,
> On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > */
> > + secmon_reserved: secmon@40000000 {
> > + reg = <0x0 0x40000000 0x0 0x80000>;
> > + no-map;
> > + };
> > + };
>
> This should still be set by the firmware
>
> > + mmc0: mmc@4020000 {
> > + compatible = "allwinner,sun50i-h616-mmc",
> > + "allwinner,sun50i-a100-mmc";
> > + reg = <0x04020000 0x1000>;
> > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > CLK_MMC0>;
> > + clock-names = "ahb", "mmc";
> > + resets = <&ccu RST_BUS_MMC0>;
> > + reset-names = "ahb";
> > + interrupts = <GIC_SPI 35
> > IRQ_TYPE_LEVEL_HIGH>;
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&mmc0_pins>;
> > + status = "disabled";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + };
>
> Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> This is biting us on the already supported SoCs, so it would be great
> to not repeat the same mistake with the new ones
Do you mean to list the "sd-uhs-sdr50" and friends properties here in
the DT?
What is the best practice here in terms putting them in the .dts vs.
the .dtsi? Surely the controller has limits, but bad traces on a board
could impose further restrictions, right?
Though that's probably rare, so it sounds like a lot of churn to list
them in every board DT. So can we list everything in here (.dtsi), then
delete in those affected boards only?
Cheers,
Andre
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [linux-sunxi] Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-14 12:53 ` Andre Przywara
@ 2020-12-14 13:28 ` Chen-Yu Tsai
-1 siblings, 0 replies; 98+ messages in thread
From: Chen-Yu Tsai @ 2020-12-14 13:28 UTC (permalink / raw)
To: André Przywara
Cc: Maxime Ripard, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree
On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:
>
> On Mon, 14 Dec 2020 10:58:31 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
>
> Hi,
>
> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > + reserved-memory {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > */
> > > + secmon_reserved: secmon@40000000 {
> > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > + no-map;
> > > + };
> > > + };
> >
> > This should still be set by the firmware
> >
> > > + mmc0: mmc@4020000 {
> > > + compatible = "allwinner,sun50i-h616-mmc",
> > > + "allwinner,sun50i-a100-mmc";
> > > + reg = <0x04020000 0x1000>;
> > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > CLK_MMC0>;
> > > + clock-names = "ahb", "mmc";
> > > + resets = <&ccu RST_BUS_MMC0>;
> > > + reset-names = "ahb";
> > > + interrupts = <GIC_SPI 35
> > > IRQ_TYPE_LEVEL_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc0_pins>;
> > > + status = "disabled";
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + };
> >
> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > This is biting us on the already supported SoCs, so it would be great
> > to not repeat the same mistake with the new ones
>
> Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> the DT?
> What is the best practice here in terms putting them in the .dts vs.
> the .dtsi? Surely the controller has limits, but bad traces on a board
> could impose further restrictions, right?
> Though that's probably rare, so it sounds like a lot of churn to list
> them in every board DT. So can we list everything in here (.dtsi), then
> delete in those affected boards only?
The driver will most certainly already have the basic high speed modes
enabled. Or we can list them in the .dtsi file.
For HS-DDR mode, we probably want to list that in the .dtsi file as well,
as that seems to be the one that is failing most of the time.
All the UHS-1 modes would be listed by board, since it requires a way
to cut power to the card and the ability to change I/O voltage levels.
I wonder if Allwinner still keeps the timing information in the driver,
or have they moved that to their vendor device tree files. We might want
to consider moving it as well.
ChenYu
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [linux-sunxi] Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-14 13:28 ` Chen-Yu Tsai
0 siblings, 0 replies; 98+ messages in thread
From: Chen-Yu Tsai @ 2020-12-14 13:28 UTC (permalink / raw)
To: André Przywara
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-kernel, linux-sunxi,
Clément Péron, Maxime Ripard, Shuosheng Huang,
linux-arm-kernel, Icenowy Zheng
On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:
>
> On Mon, 14 Dec 2020 10:58:31 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
>
> Hi,
>
> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > + reserved-memory {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > */
> > > + secmon_reserved: secmon@40000000 {
> > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > + no-map;
> > > + };
> > > + };
> >
> > This should still be set by the firmware
> >
> > > + mmc0: mmc@4020000 {
> > > + compatible = "allwinner,sun50i-h616-mmc",
> > > + "allwinner,sun50i-a100-mmc";
> > > + reg = <0x04020000 0x1000>;
> > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > CLK_MMC0>;
> > > + clock-names = "ahb", "mmc";
> > > + resets = <&ccu RST_BUS_MMC0>;
> > > + reset-names = "ahb";
> > > + interrupts = <GIC_SPI 35
> > > IRQ_TYPE_LEVEL_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc0_pins>;
> > > + status = "disabled";
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + };
> >
> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > This is biting us on the already supported SoCs, so it would be great
> > to not repeat the same mistake with the new ones
>
> Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> the DT?
> What is the best practice here in terms putting them in the .dts vs.
> the .dtsi? Surely the controller has limits, but bad traces on a board
> could impose further restrictions, right?
> Though that's probably rare, so it sounds like a lot of churn to list
> them in every board DT. So can we list everything in here (.dtsi), then
> delete in those affected boards only?
The driver will most certainly already have the basic high speed modes
enabled. Or we can list them in the .dtsi file.
For HS-DDR mode, we probably want to list that in the .dtsi file as well,
as that seems to be the one that is failing most of the time.
All the UHS-1 modes would be listed by board, since it requires a way
to cut power to the card and the ability to change I/O voltage levels.
I wonder if Allwinner still keeps the timing information in the driver,
or have they moved that to their vendor device tree files. We might want
to consider moving it as well.
ChenYu
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [linux-sunxi] Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-14 13:28 ` Chen-Yu Tsai
@ 2020-12-14 14:14 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 14:14 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: André Przywara, Jernej Skrabec, Icenowy Zheng,
Linus Walleij, Rob Herring, Clément Péron,
Shuosheng Huang, Yangtao Li, linux-arm-kernel, linux-kernel,
linux-sunxi, devicetree
[-- Attachment #1: Type: text/plain, Size: 2771 bytes --]
On Mon, Dec 14, 2020 at 09:28:36PM +0800, Chen-Yu Tsai wrote:
> On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:
> >
> > On Mon, 14 Dec 2020 10:58:31 +0100
> > Maxime Ripard <maxime@cerno.tech> wrote:
> >
> > Hi,
> >
> > > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > > + reserved-memory {
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > + ranges;
> > > > +
> > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > > */
> > > > + secmon_reserved: secmon@40000000 {
> > > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > > + no-map;
> > > > + };
> > > > + };
> > >
> > > This should still be set by the firmware
> > >
> > > > + mmc0: mmc@4020000 {
> > > > + compatible = "allwinner,sun50i-h616-mmc",
> > > > + "allwinner,sun50i-a100-mmc";
> > > > + reg = <0x04020000 0x1000>;
> > > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > > CLK_MMC0>;
> > > > + clock-names = "ahb", "mmc";
> > > > + resets = <&ccu RST_BUS_MMC0>;
> > > > + reset-names = "ahb";
> > > > + interrupts = <GIC_SPI 35
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&mmc0_pins>;
> > > > + status = "disabled";
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > + };
> > >
> > > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > > This is biting us on the already supported SoCs, so it would be great
> > > to not repeat the same mistake with the new ones
> >
> > Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> > the DT?
> > What is the best practice here in terms putting them in the .dts vs.
> > the .dtsi? Surely the controller has limits, but bad traces on a board
> > could impose further restrictions, right?
> > Though that's probably rare, so it sounds like a lot of churn to list
> > them in every board DT. So can we list everything in here (.dtsi), then
> > delete in those affected boards only?
>
> The driver will most certainly already have the basic high speed modes
> enabled. Or we can list them in the .dtsi file.
I'd list them all in the DTSI, trying to be smart has bitten us already
so I'd like to avoid it as much as possible.
And if we find a better way, we can set it in the driver if it's in the
DTSI already. doing the opposite would be harder
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [linux-sunxi] Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-14 14:14 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 14:14 UTC (permalink / raw)
To: Chen-Yu Tsai
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
André Przywara, Linus Walleij, linux-kernel, linux-sunxi,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2771 bytes --]
On Mon, Dec 14, 2020 at 09:28:36PM +0800, Chen-Yu Tsai wrote:
> On Mon, Dec 14, 2020 at 8:53 PM Andre Przywara <andre.przywara@arm.com> wrote:
> >
> > On Mon, 14 Dec 2020 10:58:31 +0100
> > Maxime Ripard <maxime@cerno.tech> wrote:
> >
> > Hi,
> >
> > > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > > + reserved-memory {
> > > > + #address-cells = <2>;
> > > > + #size-cells = <2>;
> > > > + ranges;
> > > > +
> > > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > > */
> > > > + secmon_reserved: secmon@40000000 {
> > > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > > + no-map;
> > > > + };
> > > > + };
> > >
> > > This should still be set by the firmware
> > >
> > > > + mmc0: mmc@4020000 {
> > > > + compatible = "allwinner,sun50i-h616-mmc",
> > > > + "allwinner,sun50i-a100-mmc";
> > > > + reg = <0x04020000 0x1000>;
> > > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > > CLK_MMC0>;
> > > > + clock-names = "ahb", "mmc";
> > > > + resets = <&ccu RST_BUS_MMC0>;
> > > > + reset-names = "ahb";
> > > > + interrupts = <GIC_SPI 35
> > > > IRQ_TYPE_LEVEL_HIGH>;
> > > > + pinctrl-names = "default";
> > > > + pinctrl-0 = <&mmc0_pins>;
> > > > + status = "disabled";
> > > > + #address-cells = <1>;
> > > > + #size-cells = <0>;
> > > > + };
> > >
> > > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > > This is biting us on the already supported SoCs, so it would be great
> > > to not repeat the same mistake with the new ones
> >
> > Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> > the DT?
> > What is the best practice here in terms putting them in the .dts vs.
> > the .dtsi? Surely the controller has limits, but bad traces on a board
> > could impose further restrictions, right?
> > Though that's probably rare, so it sounds like a lot of churn to list
> > them in every board DT. So can we list everything in here (.dtsi), then
> > delete in those affected boards only?
>
> The driver will most certainly already have the basic high speed modes
> enabled. Or we can list them in the .dtsi file.
I'd list them all in the DTSI, trying to be smart has bitten us already
so I'd like to avoid it as much as possible.
And if we find a better way, we can set it in the driver if it's in the
DTSI already. doing the opposite would be harder
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
2020-12-14 12:53 ` Andre Przywara
@ 2020-12-14 14:12 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 14:12 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree
[-- Attachment #1: Type: text/plain, Size: 1915 bytes --]
On Mon, Dec 14, 2020 at 12:53:43PM +0000, Andre Przywara wrote:
> On Mon, 14 Dec 2020 10:58:31 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > + reserved-memory {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > */
> > > + secmon_reserved: secmon@40000000 {
> > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > + no-map;
> > > + };
> > > + };
> >
> > This should still be set by the firmware
> >
> > > + mmc0: mmc@4020000 {
> > > + compatible = "allwinner,sun50i-h616-mmc",
> > > + "allwinner,sun50i-a100-mmc";
> > > + reg = <0x04020000 0x1000>;
> > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > CLK_MMC0>;
> > > + clock-names = "ahb", "mmc";
> > > + resets = <&ccu RST_BUS_MMC0>;
> > > + reset-names = "ahb";
> > > + interrupts = <GIC_SPI 35
> > > IRQ_TYPE_LEVEL_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc0_pins>;
> > > + status = "disabled";
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + };
> >
> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > This is biting us on the already supported SoCs, so it would be great
> > to not repeat the same mistake with the new ones
>
> Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> the DT?
> What is the best practice here in terms putting them in the .dts vs.
> the .dtsi? Surely the controller has limits, but bad traces on a board
> could impose further restrictions, right?
>
> Though that's probably rare, so it sounds like a lot of churn to list
> them in every board DT. So can we list everything in here (.dtsi), then
> delete in those affected boards only?
Yeah, I completely agree :)
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 19/21] arm64: dts: allwinner: Add Allwinner H616 .dtsi file
@ 2020-12-14 14:12 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 14:12 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 1915 bytes --]
On Mon, Dec 14, 2020 at 12:53:43PM +0000, Andre Przywara wrote:
> On Mon, 14 Dec 2020 10:58:31 +0100
> Maxime Ripard <maxime@cerno.tech> wrote:
> > On Fri, Dec 11, 2020 at 01:19:32AM +0000, Andre Przywara wrote:
> > > + reserved-memory {
> > > + #address-cells = <2>;
> > > + #size-cells = <2>;
> > > + ranges;
> > > +
> > > + /* 512KiB reserved for ARM Trusted Firmware (BL31)
> > > */
> > > + secmon_reserved: secmon@40000000 {
> > > + reg = <0x0 0x40000000 0x0 0x80000>;
> > > + no-map;
> > > + };
> > > + };
> >
> > This should still be set by the firmware
> >
> > > + mmc0: mmc@4020000 {
> > > + compatible = "allwinner,sun50i-h616-mmc",
> > > + "allwinner,sun50i-a100-mmc";
> > > + reg = <0x04020000 0x1000>;
> > > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu
> > > CLK_MMC0>;
> > > + clock-names = "ahb", "mmc";
> > > + resets = <&ccu RST_BUS_MMC0>;
> > > + reset-names = "ahb";
> > > + interrupts = <GIC_SPI 35
> > > IRQ_TYPE_LEVEL_HIGH>;
> > > + pinctrl-names = "default";
> > > + pinctrl-0 = <&mmc0_pins>;
> > > + status = "disabled";
> > > + #address-cells = <1>;
> > > + #size-cells = <0>;
> > > + };
> >
> > Somewhat related: we shouldn't set the MMC speed flags in the drivers.
> > This is biting us on the already supported SoCs, so it would be great
> > to not repeat the same mistake with the new ones
>
> Do you mean to list the "sd-uhs-sdr50" and friends properties here in
> the DT?
> What is the best practice here in terms putting them in the .dts vs.
> the .dtsi? Surely the controller has limits, but bad traces on a board
> could impose further restrictions, right?
>
> Though that's probably rare, so it sounds like a lot of churn to list
> them in every board DT. So can we list everything in here (.dtsi), then
> delete in those affected boards only?
Yeah, I completely agree :)
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 20/21] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, devicetree
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index cab8e1b6417b..5f8b5c896e66 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -894,4 +894,9 @@ properties:
- const: xunlong,orangepi-zero-plus2-h3
- const: allwinner,sun8i-h3
+ - description: Xunlong OrangePi Zero 2
+ items:
+ - const: xunlong,orangepi-zero2
+ - const: allwinner,sun50i-h616
+
additionalProperties: true
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 20/21] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml
index cab8e1b6417b..5f8b5c896e66 100644
--- a/Documentation/devicetree/bindings/arm/sunxi.yaml
+++ b/Documentation/devicetree/bindings/arm/sunxi.yaml
@@ -894,4 +894,9 @@ properties:
- const: xunlong,orangepi-zero-plus2-h3
- const: allwinner,sun8i-h3
+ - description: Xunlong OrangePi Zero 2
+ items:
+ - const: xunlong,orangepi-zero2
+ - const: allwinner,sun50i-h616
+
additionalProperties: true
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 20/21] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 22:56 ` Rob Herring
-1 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:56 UTC (permalink / raw)
To: Andre Przywara
Cc: linux-sunxi, linux-arm-kernel, Jernej Skrabec, linux-kernel,
Linus Walleij, Maxime Ripard, devicetree, Shuosheng Huang,
Clément Péron, Yangtao Li, Chen-Yu Tsai, Icenowy Zheng
On Fri, 11 Dec 2020 01:19:33 +0000, Andre Przywara wrote:
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 20/21] dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
@ 2020-12-14 22:56 ` Rob Herring
0 siblings, 0 replies; 98+ messages in thread
From: Rob Herring @ 2020-12-14 22:56 UTC (permalink / raw)
To: Andre Przywara
Cc: devicetree, Jernej Skrabec, Yangtao Li, Linus Walleij,
linux-kernel, Maxime Ripard, linux-sunxi, Shuosheng Huang,
Icenowy Zheng, Clément Péron, Chen-Yu Tsai,
linux-arm-kernel
On Fri, 11 Dec 2020 01:19:33 +0000, Andre Przywara wrote:
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++
> 1 file changed, 5 insertions(+)
>
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* [PATCH v2 21/21] arm64: dts: allwinner: Add OrangePi Zero 2 .dts
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-11 1:19 ` Andre Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, devicetree
The OrangePi Zero 2 is a development board with the new H616 SoC.
It features the usual connectors used on those small boards, and comes
with the AXP305, which seems to be compatible with the AXP805.
For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++++++++++++++++
2 files changed, 241 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 211d1e9d4701..0cf8299b1ce7 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..2afc036059b4
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "OrangePi Zero2";
+ compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ status {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ status = "okay";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdce>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdce>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp305: pmic@36 {
+ compatible = "x-powers,axp305", "x-powers,axp805",
+ "x-powers,axp806";
+ reg = <0x36>;
+
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-sys";
+ };
+
+ reg_aldo2: aldo2 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext";
+ };
+
+ reg_aldo3: aldo3 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext2";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ bldo2 {
+ /* unused */
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ cldo1 {
+ /* reserved */
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-dram";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-eth-mmc";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.17.5
^ permalink raw reply related [flat|nested] 98+ messages in thread* [PATCH v2 21/21] arm64: dts: allwinner: Add OrangePi Zero 2 .dts
@ 2020-12-11 1:19 ` Andre Przywara
0 siblings, 0 replies; 98+ messages in thread
From: Andre Przywara @ 2020-12-11 1:19 UTC (permalink / raw)
To: Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, devicetree, Yangtao Li, Linus Walleij, linux-kernel,
linux-sunxi, Clément Péron, Icenowy Zheng,
Shuosheng Huang, linux-arm-kernel
The OrangePi Zero 2 is a development board with the new H616 SoC.
It features the usual connectors used on those small boards, and comes
with the AXP305, which seems to be compatible with the AXP805.
For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++++++++++++++++
2 files changed, 241 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 211d1e9d4701..0cf8299b1ce7 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..2afc036059b4
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,240 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "OrangePi Zero2";
+ compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+ aliases {
+ ethernet0 = &emac0;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ power {
+ function = LED_FUNCTION_POWER;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+ default-state = "on";
+ };
+
+ status {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+ };
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the USB-C socket */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ reg_usb1_vbus: usb1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <®_vcc5v>;
+ enable-active-high;
+ gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
+ status = "okay";
+ };
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+/* USB 2 & 3 are on headers only. */
+
+&emac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ext_rgmii_pins>;
+ phy-mode = "rgmii";
+ phy-handle = <&ext_rgmii_phy>;
+ phy-supply = <®_dcdce>;
+ allwinner,rx-delay-ps = <3100>;
+ allwinner,tx-delay-ps = <700>;
+ status = "okay";
+};
+
+&mdio0 {
+ ext_rgmii_phy: ethernet-phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <1>;
+ };
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdce>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ bus-width = <4>;
+ status = "okay";
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp305: pmic@36 {
+ compatible = "x-powers,axp305", "x-powers,axp805",
+ "x-powers,axp806";
+ reg = <0x36>;
+
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-sys";
+ };
+
+ reg_aldo2: aldo2 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext";
+ };
+
+ reg_aldo3: aldo3 { /* 3.3V on headers */
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3-ext2";
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ bldo2 {
+ /* unused */
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ cldo1 {
+ /* reserved */
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1080000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ reg_dcdcd: dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vdd-dram";
+ };
+
+ reg_dcdce: dcdce {
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-eth-mmc";
+ };
+
+ sw {
+ /* unused */
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <40000000>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "peripheral";
+ status = "okay";
+};
+
+&usbphy {
+ usb1_vbus-supply = <®_usb1_vbus>;
+ status = "okay";
+};
--
2.17.5
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related [flat|nested] 98+ messages in thread* Re: [PATCH v2 21/21] arm64: dts: allwinner: Add OrangePi Zero 2 .dts
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-14 9:59 ` Maxime Ripard
-1 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:59 UTC (permalink / raw)
To: Andre Przywara
Cc: Chen-Yu Tsai, Jernej Skrabec, Icenowy Zheng, Linus Walleij,
Rob Herring, Clément Péron, Shuosheng Huang,
Yangtao Li, linux-arm-kernel, linux-kernel, linux-sunxi,
devicetree
[-- Attachment #1: Type: text/plain, Size: 2211 bytes --]
On Fri, Dec 11, 2020 at 01:19:34AM +0000, Andre Przywara wrote:
> The OrangePi Zero 2 is a development board with the new H616 SoC.
>
> It features the usual connectors used on those small boards, and comes
> with the AXP305, which seems to be compatible with the AXP805.
>
> For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++++++++++++++++
> 2 files changed, 241 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 211d1e9d4701..0cf8299b1ce7 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> new file mode 100644
> index 000000000000..2afc036059b4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -0,0 +1,240 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2020 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "OrangePi Zero2";
> + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
> +
> + aliases {
> + ethernet0 = &emac0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
This isn't a valid node name
Maxime
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 98+ messages in thread* Re: [PATCH v2 21/21] arm64: dts: allwinner: Add OrangePi Zero 2 .dts
@ 2020-12-14 9:59 ` Maxime Ripard
0 siblings, 0 replies; 98+ messages in thread
From: Maxime Ripard @ 2020-12-14 9:59 UTC (permalink / raw)
To: Andre Przywara
Cc: Rob Herring, Jernej Skrabec, devicetree, Yangtao Li,
Linus Walleij, linux-sunxi, linux-kernel, Chen-Yu Tsai,
Clément Péron, Icenowy Zheng, Shuosheng Huang,
linux-arm-kernel
[-- Attachment #1.1: Type: text/plain, Size: 2211 bytes --]
On Fri, Dec 11, 2020 at 01:19:34AM +0000, Andre Przywara wrote:
> The OrangePi Zero 2 is a development board with the new H616 SoC.
>
> It features the usual connectors used on those small boards, and comes
> with the AXP305, which seems to be compatible with the AXP805.
>
> For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++++++++++++++++
> 2 files changed, 241 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 211d1e9d4701..0cf8299b1ce7 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> new file mode 100644
> index 000000000000..2afc036059b4
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -0,0 +1,240 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2020 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> + model = "OrangePi Zero2";
> + compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
> +
> + aliases {
> + ethernet0 = &emac0;
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + power {
This isn't a valid node name
Maxime
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
2020-12-11 1:19 ` Andre Przywara
@ 2020-12-13 17:47 ` Icenowy Zheng
-1 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-13 17:47 UTC (permalink / raw)
To: Andre Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, Philipp Zabel
在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> Hi,
>
> this is the quite expanded second version of the support series for
> the
> Allwinner H616 SoC.
> Besides many fixes for the bugs discovered by the diligent reviewers
> (many thanks for that!) this version adds some patches to support
> some
> slightly changed devices, like the second EMAC and the AXP not having
> an interrupt.
> Also I added quite some DT binding doc patches.
> USB still does not work, but I include the patches anyway, hoping
> that
> someone can help spotting the issue.
> For a more detailed changelog see below.
>
> Thanks!
> Andre
>
> ==================
> This series gathers patches to support the Allwinner H616 SoC. This
> is
> a rather uninspired SoC (Quad-A53 with the usual peripherals), but
> allows for some cheap development boards and TV boxes, and supports
> up to 4GB of DRAM.
>
> Various DT binding patches are sprinkled throughout the series, to
> add
> the new compatible names right before they are used.
> Patch 1/21 is the usual drive-by fix, discovered while staring at
> the H6 clock code.
> Patch 3 and 4 add pinctrl support, with the "-R" controller now being
> crippled down to two I2C pins only. If we grow tired of repeating
> this
> exercise for every new SoC variant, I am happy to revive my more
> versatile sunxi pinctrl driver effort from a few years back [1].
> Patch 6 and 7 add clock support. For the -R clock this is shared with
> the H6 code, as the clocks are identical, with the H616 just having
> fewer of them. The main clocks are different enough to warrant a
> separate
> file.
> Patch 08/21 is pulling a patch from Yangtao's A100 series, since we
> need
> the same fix for MMC support. This will probably be merged
> separately,
> I just include this here to provide a bootable solution.
> Patch 10 teaches the AXP MFD driver to get along without having an
> interrupt, as the H616 apparently does not have an NMI controller
> anymore.
> Patch 12 and 13 add some tweaks to the syscon and EMAC driver, to
> deal
> with the second EMAC clock used for the second Ethernet controller.
> Patches 14 and 15 *try* to add USB support. The same approach works
> with
> the very similar U-Boot PHY driver, but for some reason still fail in
> Linux. Maybe someone spots the issue and can help fixing it?
There's a judge currently checks for phy type A83T/H6. You may need to
add H616 there.
Or should we have a bool in the data struct to mark it? I think all
chips that need that is 28nm.
>
> The remaining patches add DT bindings, which just add the new
> compatible
> string along with an existing name as a fallback string.
> Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
> the OrangePi Zero2 board[2] in the last patch.
>
> We have U-Boot and Trusted-Firmware support in a working state,
> booting
> via FEL and even TFTPing kernels work already [3][4].
>
> Many thanks to Jernej for his tremendous help on this, also for the
> awesome input and help from the #linux-sunxi Freenode channel.
>
> The whole series can also be found here:
> https://github.com/apritzel/linux/commits/h616-v2
>
> Happy reviewing!
>
> Cheers,
> Andre
>
> [1]
> https://patchwork.ozlabs.org/project/linux-gpio/cover/20171113012523.2328-1-andre.przywara@arm.com/
> [2] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
> [3] https://github.com/jernejsk/u-boot/commits/h616-v1
> [4] https://github.com/apritzel/arm-trusted-firmware/commits/h616-WIP
>
> Changelog v1 .. v2:
> - pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
> - use differing h_i2s0 pin output names
> - r-ccu: fix number of used clocks
> - ccu: remove PLL-PERIPHy(4X)
> - ccu: fix gpu1 divider range
> - ccu: fix usb-phy3 parent
> - ccu: add missing TV clocks
> - ccu: rework to CLK_OF_DECLARE style
> - ccu: enable output bit for PLL clocks
> - ccu: renumber clocks
> - .dtsi: drop sun50i-a64-system-control fallback
> - .dtsi: drop unknown SRAM regions
> - .dtsi: add more (undocumented) GPIO interrupts
> - .dtsi: fix I2C3 pin names
> - .dtsi: use a100-emmc fallback for MMC2
> - .dtsi: add second EMAC controller
> - .dtsi: use H3 MUSB controller fallback
> - .dtsi: fix frame size for USB PHY PMU registers
> - .dtsi: add USB0 PHY references
> - .dtsi: fix IR controller clock source
> - .dts: fix LED naming and swap pins
> - .dts: use 5V supply parent for USB supply
> - .dts: drop dummy IRQ for AXP
> - .dts: enable 3V3 header pin power rail
> - .dts: add SPI flash node
> - .dts: make USB-C port peripheral only
> - add IRQ-less AXP support
> - add two patches to support more than one EMAC clock
> - add patch to rework and extend USB PHY support
> - add DT binding documentation patches
>
> Andre Przywara (18):
> clk: sunxi-ng: h6: Fix clock divider range on some clocks
> dt-bindings: pinctrl: Add Allwinner H616 compatible strings
> pinctrl: sunxi: Add support for the Allwinner H616 pin controller
> pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
> dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner
> H616
> clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
> clk: sunxi-ng: Add support for the Allwinner H616 CCU
> mfd: axp20x: Allow AXP chips without interrupt lines
> dt-bindings: sram: sunxi-sram: Add H616 compatible string
> soc: sunxi: sram: Add support for more than one EMAC clock
> net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
> phy: sun4i-usb: Rework "pmu_unk1" handling
> phy: sun4i-usb: Add support for the H616 USB PHY
> dt-bindings: watchdog: sun4i: Add H616 compatible string
> dt-bindings: allwinner: Add H616 compatible strings
> arm64: dts: allwinner: Add Allwinner H616 .dtsi file
> dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
> arm64: dts: allwinner: Add OrangePi Zero 2 .dts
>
> Yangtao Li (3):
> dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
> mmc: sunxi: add support for A100 mmc controller
> dt-bindings: watchdog: sun4i: Add A100 compatible
>
> .../devicetree/bindings/arm/sunxi.yaml | 5 +
> .../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
> .../media/allwinner,sun4i-a10-ir.yaml | 16 +-
> .../bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 +
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 2 +
> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
> .../allwinner,sun4i-a10-system-control.yaml | 1 +
> .../watchdog/allwinner,sun4i-a10-wdt.yaml | 9 +-
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++
> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++
> drivers/clk/sunxi-ng/Kconfig | 7 +-
> drivers/clk/sunxi-ng/Makefile | 1 +
> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150
> +++++++++++++++++
> drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
> drivers/mfd/axp20x.c | 17 +-
> drivers/mmc/host/sunxi-mmc.c | 28 +-
> .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
> drivers/phy/allwinner/phy-sun4i-usb.c | 39 +-
> drivers/pinctrl/sunxi/Kconfig | 10 +
> drivers/pinctrl/sunxi/Makefile | 2 +
> drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +
> drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++
> drivers/soc/sunxi/sunxi_sram.c | 31 +-
> include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
> include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
> 31 files changed, 3151 insertions(+), 71 deletions(-)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-
> orangepi-zero2.dts
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
> create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
@ 2020-12-13 17:47 ` Icenowy Zheng
0 siblings, 0 replies; 98+ messages in thread
From: Icenowy Zheng @ 2020-12-13 17:47 UTC (permalink / raw)
To: Andre Przywara, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Philipp Zabel, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
> Hi,
>
> this is the quite expanded second version of the support series for
> the
> Allwinner H616 SoC.
> Besides many fixes for the bugs discovered by the diligent reviewers
> (many thanks for that!) this version adds some patches to support
> some
> slightly changed devices, like the second EMAC and the AXP not having
> an interrupt.
> Also I added quite some DT binding doc patches.
> USB still does not work, but I include the patches anyway, hoping
> that
> someone can help spotting the issue.
> For a more detailed changelog see below.
>
> Thanks!
> Andre
>
> ==================
> This series gathers patches to support the Allwinner H616 SoC. This
> is
> a rather uninspired SoC (Quad-A53 with the usual peripherals), but
> allows for some cheap development boards and TV boxes, and supports
> up to 4GB of DRAM.
>
> Various DT binding patches are sprinkled throughout the series, to
> add
> the new compatible names right before they are used.
> Patch 1/21 is the usual drive-by fix, discovered while staring at
> the H6 clock code.
> Patch 3 and 4 add pinctrl support, with the "-R" controller now being
> crippled down to two I2C pins only. If we grow tired of repeating
> this
> exercise for every new SoC variant, I am happy to revive my more
> versatile sunxi pinctrl driver effort from a few years back [1].
> Patch 6 and 7 add clock support. For the -R clock this is shared with
> the H6 code, as the clocks are identical, with the H616 just having
> fewer of them. The main clocks are different enough to warrant a
> separate
> file.
> Patch 08/21 is pulling a patch from Yangtao's A100 series, since we
> need
> the same fix for MMC support. This will probably be merged
> separately,
> I just include this here to provide a bootable solution.
> Patch 10 teaches the AXP MFD driver to get along without having an
> interrupt, as the H616 apparently does not have an NMI controller
> anymore.
> Patch 12 and 13 add some tweaks to the syscon and EMAC driver, to
> deal
> with the second EMAC clock used for the second Ethernet controller.
> Patches 14 and 15 *try* to add USB support. The same approach works
> with
> the very similar U-Boot PHY driver, but for some reason still fail in
> Linux. Maybe someone spots the issue and can help fixing it?
There's a judge currently checks for phy type A83T/H6. You may need to
add H616 there.
Or should we have a bool in the data struct to mark it? I think all
chips that need that is 28nm.
>
> The remaining patches add DT bindings, which just add the new
> compatible
> string along with an existing name as a fallback string.
> Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
> the OrangePi Zero2 board[2] in the last patch.
>
> We have U-Boot and Trusted-Firmware support in a working state,
> booting
> via FEL and even TFTPing kernels work already [3][4].
>
> Many thanks to Jernej for his tremendous help on this, also for the
> awesome input and help from the #linux-sunxi Freenode channel.
>
> The whole series can also be found here:
> https://github.com/apritzel/linux/commits/h616-v2
>
> Happy reviewing!
>
> Cheers,
> Andre
>
> [1]
> https://patchwork.ozlabs.org/project/linux-gpio/cover/20171113012523.2328-1-andre.przywara@arm.com/
> [2] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
> [3] https://github.com/jernejsk/u-boot/commits/h616-v1
> [4] https://github.com/apritzel/arm-trusted-firmware/commits/h616-WIP
>
> Changelog v1 .. v2:
> - pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
> - use differing h_i2s0 pin output names
> - r-ccu: fix number of used clocks
> - ccu: remove PLL-PERIPHy(4X)
> - ccu: fix gpu1 divider range
> - ccu: fix usb-phy3 parent
> - ccu: add missing TV clocks
> - ccu: rework to CLK_OF_DECLARE style
> - ccu: enable output bit for PLL clocks
> - ccu: renumber clocks
> - .dtsi: drop sun50i-a64-system-control fallback
> - .dtsi: drop unknown SRAM regions
> - .dtsi: add more (undocumented) GPIO interrupts
> - .dtsi: fix I2C3 pin names
> - .dtsi: use a100-emmc fallback for MMC2
> - .dtsi: add second EMAC controller
> - .dtsi: use H3 MUSB controller fallback
> - .dtsi: fix frame size for USB PHY PMU registers
> - .dtsi: add USB0 PHY references
> - .dtsi: fix IR controller clock source
> - .dts: fix LED naming and swap pins
> - .dts: use 5V supply parent for USB supply
> - .dts: drop dummy IRQ for AXP
> - .dts: enable 3V3 header pin power rail
> - .dts: add SPI flash node
> - .dts: make USB-C port peripheral only
> - add IRQ-less AXP support
> - add two patches to support more than one EMAC clock
> - add patch to rework and extend USB PHY support
> - add DT binding documentation patches
>
> Andre Przywara (18):
> clk: sunxi-ng: h6: Fix clock divider range on some clocks
> dt-bindings: pinctrl: Add Allwinner H616 compatible strings
> pinctrl: sunxi: Add support for the Allwinner H616 pin controller
> pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
> dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner
> H616
> clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
> clk: sunxi-ng: Add support for the Allwinner H616 CCU
> mfd: axp20x: Allow AXP chips without interrupt lines
> dt-bindings: sram: sunxi-sram: Add H616 compatible string
> soc: sunxi: sram: Add support for more than one EMAC clock
> net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
> phy: sun4i-usb: Rework "pmu_unk1" handling
> phy: sun4i-usb: Add support for the H616 USB PHY
> dt-bindings: watchdog: sun4i: Add H616 compatible string
> dt-bindings: allwinner: Add H616 compatible strings
> arm64: dts: allwinner: Add Allwinner H616 .dtsi file
> dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
> arm64: dts: allwinner: Add OrangePi Zero 2 .dts
>
> Yangtao Li (3):
> dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
> mmc: sunxi: add support for A100 mmc controller
> dt-bindings: watchdog: sun4i: Add A100 compatible
>
> .../devicetree/bindings/arm/sunxi.yaml | 5 +
> .../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
> .../media/allwinner,sun4i-a10-ir.yaml | 16 +-
> .../bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 +
> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 2 +
> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
> .../allwinner,sun4i-a10-system-control.yaml | 1 +
> .../watchdog/allwinner,sun4i-a10-wdt.yaml | 9 +-
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++
> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++
> drivers/clk/sunxi-ng/Kconfig | 7 +-
> drivers/clk/sunxi-ng/Makefile | 1 +
> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 +-
> drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150
> +++++++++++++++++
> drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
> drivers/mfd/axp20x.c | 17 +-
> drivers/mmc/host/sunxi-mmc.c | 28 +-
> .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
> drivers/phy/allwinner/phy-sun4i-usb.c | 39 +-
> drivers/pinctrl/sunxi/Kconfig | 10 +
> drivers/pinctrl/sunxi/Makefile | 2 +
> drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +
> drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++
> drivers/soc/sunxi/sunxi_sram.c | 31 +-
> include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
> include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
> 31 files changed, 3151 insertions(+), 71 deletions(-)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-
> orangepi-zero2.dts
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
> create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
> create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
2020-12-13 17:47 ` Icenowy Zheng
@ 2020-12-14 1:18 ` André Przywara
-1 siblings, 0 replies; 98+ messages in thread
From: André Przywara @ 2020-12-14 1:18 UTC (permalink / raw)
To: Icenowy Zheng, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Icenowy Zheng, Linus Walleij, Rob Herring,
Clément Péron, Shuosheng Huang, Yangtao Li,
linux-arm-kernel, linux-kernel, linux-sunxi, Michael Turquette,
Stephen Boyd, Philipp Zabel
On 13/12/2020 17:47, Icenowy Zheng wrote:
Hi Icenowy,
> 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
>> Hi,
>>
>> this is the quite expanded second version of the support series for
>> the
>> Allwinner H616 SoC.
>> Besides many fixes for the bugs discovered by the diligent reviewers
>> (many thanks for that!) this version adds some patches to support
>> some
>> slightly changed devices, like the second EMAC and the AXP not having
>> an interrupt.
>> Also I added quite some DT binding doc patches.
>> USB still does not work, but I include the patches anyway, hoping
>> that
>> someone can help spotting the issue.
>> For a more detailed changelog see below.
>>
>> Thanks!
>> Andre
>>
>> ==================
>> This series gathers patches to support the Allwinner H616 SoC. This
>> is
>> a rather uninspired SoC (Quad-A53 with the usual peripherals), but
>> allows for some cheap development boards and TV boxes, and supports
>> up to 4GB of DRAM.
>>
>> Various DT binding patches are sprinkled throughout the series, to
>> add
>> the new compatible names right before they are used.
>> Patch 1/21 is the usual drive-by fix, discovered while staring at
>> the H6 clock code.
>> Patch 3 and 4 add pinctrl support, with the "-R" controller now being
>> crippled down to two I2C pins only. If we grow tired of repeating
>> this
>> exercise for every new SoC variant, I am happy to revive my more
>> versatile sunxi pinctrl driver effort from a few years back [1].
>> Patch 6 and 7 add clock support. For the -R clock this is shared with
>> the H6 code, as the clocks are identical, with the H616 just having
>> fewer of them. The main clocks are different enough to warrant a
>> separate
>> file.
>> Patch 08/21 is pulling a patch from Yangtao's A100 series, since we
>> need
>> the same fix for MMC support. This will probably be merged
>> separately,
>> I just include this here to provide a bootable solution.
>> Patch 10 teaches the AXP MFD driver to get along without having an
>> interrupt, as the H616 apparently does not have an NMI controller
>> anymore.
>> Patch 12 and 13 add some tweaks to the syscon and EMAC driver, to
>> deal
>> with the second EMAC clock used for the second Ethernet controller.
>> Patches 14 and 15 *try* to add USB support. The same approach works
>> with
>> the very similar U-Boot PHY driver, but for some reason still fail in
>> Linux. Maybe someone spots the issue and can help fixing it?
>
> There's a judge currently checks for phy type A83T/H6. You may need to
> add H616 there.
You mean for setting PHY_CTL_VBUSVLDEXT and clearing PHY_CTL_SIDDQ? This
is guarded by .type == sun50i_h6_phy, which I also use for the H616.
So this should be covered.
> Or should we have a bool in the data struct to mark it? I think all
> chips that need that is 28nm.
Yeah, the usage of .type seems somewhat arbitrary, at the end of the day
it's just another quirk for a group of SoCs.
Thanks!
Andre
>
>>
>> The remaining patches add DT bindings, which just add the new
>> compatible
>> string along with an existing name as a fallback string.
>> Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
>> the OrangePi Zero2 board[2] in the last patch.
>>
>> We have U-Boot and Trusted-Firmware support in a working state,
>> booting
>> via FEL and even TFTPing kernels work already [3][4].
>>
>> Many thanks to Jernej for his tremendous help on this, also for the
>> awesome input and help from the #linux-sunxi Freenode channel.
>>
>> The whole series can also be found here:
>> https://github.com/apritzel/linux/commits/h616-v2
>>
>> Happy reviewing!
>>
>> Cheers,
>> Andre
>>
>> [1]
>> https://patchwork.ozlabs.org/project/linux-gpio/cover/20171113012523.2328-1-andre.przywara@arm.com/
>> [2] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
>> [3] https://github.com/jernejsk/u-boot/commits/h616-v1
>> [4] https://github.com/apritzel/arm-trusted-firmware/commits/h616-WIP
>>
>> Changelog v1 .. v2:
>> - pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
>> - use differing h_i2s0 pin output names
>> - r-ccu: fix number of used clocks
>> - ccu: remove PLL-PERIPHy(4X)
>> - ccu: fix gpu1 divider range
>> - ccu: fix usb-phy3 parent
>> - ccu: add missing TV clocks
>> - ccu: rework to CLK_OF_DECLARE style
>> - ccu: enable output bit for PLL clocks
>> - ccu: renumber clocks
>> - .dtsi: drop sun50i-a64-system-control fallback
>> - .dtsi: drop unknown SRAM regions
>> - .dtsi: add more (undocumented) GPIO interrupts
>> - .dtsi: fix I2C3 pin names
>> - .dtsi: use a100-emmc fallback for MMC2
>> - .dtsi: add second EMAC controller
>> - .dtsi: use H3 MUSB controller fallback
>> - .dtsi: fix frame size for USB PHY PMU registers
>> - .dtsi: add USB0 PHY references
>> - .dtsi: fix IR controller clock source
>> - .dts: fix LED naming and swap pins
>> - .dts: use 5V supply parent for USB supply
>> - .dts: drop dummy IRQ for AXP
>> - .dts: enable 3V3 header pin power rail
>> - .dts: add SPI flash node
>> - .dts: make USB-C port peripheral only
>> - add IRQ-less AXP support
>> - add two patches to support more than one EMAC clock
>> - add patch to rework and extend USB PHY support
>> - add DT binding documentation patches
>>
>> Andre Przywara (18):
>> clk: sunxi-ng: h6: Fix clock divider range on some clocks
>> dt-bindings: pinctrl: Add Allwinner H616 compatible strings
>> pinctrl: sunxi: Add support for the Allwinner H616 pin controller
>> pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
>> dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner
>> H616
>> clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
>> clk: sunxi-ng: Add support for the Allwinner H616 CCU
>> mfd: axp20x: Allow AXP chips without interrupt lines
>> dt-bindings: sram: sunxi-sram: Add H616 compatible string
>> soc: sunxi: sram: Add support for more than one EMAC clock
>> net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
>> phy: sun4i-usb: Rework "pmu_unk1" handling
>> phy: sun4i-usb: Add support for the H616 USB PHY
>> dt-bindings: watchdog: sun4i: Add H616 compatible string
>> dt-bindings: allwinner: Add H616 compatible strings
>> arm64: dts: allwinner: Add Allwinner H616 .dtsi file
>> dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
>> arm64: dts: allwinner: Add OrangePi Zero 2 .dts
>>
>> Yangtao Li (3):
>> dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
>> mmc: sunxi: add support for A100 mmc controller
>> dt-bindings: watchdog: sun4i: Add A100 compatible
>>
>> .../devicetree/bindings/arm/sunxi.yaml | 5 +
>> .../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
>> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
>> .../media/allwinner,sun4i-a10-ir.yaml | 16 +-
>> .../bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 +
>> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 2 +
>> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
>> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
>> .../allwinner,sun4i-a10-system-control.yaml | 1 +
>> .../watchdog/allwinner,sun4i-a10-wdt.yaml | 9 +-
>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++
>> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++
>> drivers/clk/sunxi-ng/Kconfig | 7 +-
>> drivers/clk/sunxi-ng/Makefile | 1 +
>> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150
>> +++++++++++++++++
>> drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
>> drivers/mfd/axp20x.c | 17 +-
>> drivers/mmc/host/sunxi-mmc.c | 28 +-
>> .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
>> drivers/phy/allwinner/phy-sun4i-usb.c | 39 +-
>> drivers/pinctrl/sunxi/Kconfig | 10 +
>> drivers/pinctrl/sunxi/Makefile | 2 +
>> drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +
>> drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++
>> drivers/soc/sunxi/sunxi_sram.c | 31 +-
>> include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
>> include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
>> 31 files changed, 3151 insertions(+), 71 deletions(-)
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-
>> orangepi-zero2.dts
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
>> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
>> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
>> create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
>> create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
>>
^ permalink raw reply [flat|nested] 98+ messages in thread
* Re: [PATCH v2 00/21] arm64: sunxi: Initial Allwinner H616 SoC support
@ 2020-12-14 1:18 ` André Przywara
0 siblings, 0 replies; 98+ messages in thread
From: André Przywara @ 2020-12-14 1:18 UTC (permalink / raw)
To: Icenowy Zheng, Maxime Ripard, Chen-Yu Tsai, Jernej Skrabec
Cc: Rob Herring, Yangtao Li, Linus Walleij, linux-kernel,
Stephen Boyd, linux-sunxi, Clément Péron,
Icenowy Zheng, Philipp Zabel, Shuosheng Huang, Michael Turquette,
linux-arm-kernel
On 13/12/2020 17:47, Icenowy Zheng wrote:
Hi Icenowy,
> 在 2020-12-11星期五的 01:19 +0000，Andre Przywara写道：
>> Hi,
>>
>> this is the quite expanded second version of the support series for
>> the
>> Allwinner H616 SoC.
>> Besides many fixes for the bugs discovered by the diligent reviewers
>> (many thanks for that!) this version adds some patches to support
>> some
>> slightly changed devices, like the second EMAC and the AXP not having
>> an interrupt.
>> Also I added quite some DT binding doc patches.
>> USB still does not work, but I include the patches anyway, hoping
>> that
>> someone can help spotting the issue.
>> For a more detailed changelog see below.
>>
>> Thanks!
>> Andre
>>
>> ==================
>> This series gathers patches to support the Allwinner H616 SoC. This
>> is
>> a rather uninspired SoC (Quad-A53 with the usual peripherals), but
>> allows for some cheap development boards and TV boxes, and supports
>> up to 4GB of DRAM.
>>
>> Various DT binding patches are sprinkled throughout the series, to
>> add
>> the new compatible names right before they are used.
>> Patch 1/21 is the usual drive-by fix, discovered while staring at
>> the H6 clock code.
>> Patch 3 and 4 add pinctrl support, with the "-R" controller now being
>> crippled down to two I2C pins only. If we grow tired of repeating
>> this
>> exercise for every new SoC variant, I am happy to revive my more
>> versatile sunxi pinctrl driver effort from a few years back [1].
>> Patch 6 and 7 add clock support. For the -R clock this is shared with
>> the H6 code, as the clocks are identical, with the H616 just having
>> fewer of them. The main clocks are different enough to warrant a
>> separate
>> file.
>> Patch 08/21 is pulling a patch from Yangtao's A100 series, since we
>> need
>> the same fix for MMC support. This will probably be merged
>> separately,
>> I just include this here to provide a bootable solution.
>> Patch 10 teaches the AXP MFD driver to get along without having an
>> interrupt, as the H616 apparently does not have an NMI controller
>> anymore.
>> Patch 12 and 13 add some tweaks to the syscon and EMAC driver, to
>> deal
>> with the second EMAC clock used for the second Ethernet controller.
>> Patches 14 and 15 *try* to add USB support. The same approach works
>> with
>> the very similar U-Boot PHY driver, but for some reason still fail in
>> Linux. Maybe someone spots the issue and can help fixing it?
>
> There's a judge currently checks for phy type A83T/H6. You may need to
> add H616 there.
You mean for setting PHY_CTL_VBUSVLDEXT and clearing PHY_CTL_SIDDQ? This
is guarded by .type == sun50i_h6_phy, which I also use for the H616.
So this should be covered.
> Or should we have a bool in the data struct to mark it? I think all
> chips that need that is 28nm.
Yeah, the usage of .type seems somewhat arbitrary, at the end of the day
it's just another quirk for a group of SoCs.
Thanks!
Andre
>
>>
>> The remaining patches add DT bindings, which just add the new
>> compatible
>> string along with an existing name as a fallback string.
>> Eventually we get the .dtsi for the SoC in patch 19, and the .dts for
>> the OrangePi Zero2 board[2] in the last patch.
>>
>> We have U-Boot and Trusted-Firmware support in a working state,
>> booting
>> via FEL and even TFTPing kernels work already [3][4].
>>
>> Many thanks to Jernej for his tremendous help on this, also for the
>> awesome input and help from the #linux-sunxi Freenode channel.
>>
>> The whole series can also be found here:
>> https://github.com/apritzel/linux/commits/h616-v2
>>
>> Happy reviewing!
>>
>> Cheers,
>> Andre
>>
>> [1]
>> https://patchwork.ozlabs.org/project/linux-gpio/cover/20171113012523.2328-1-andre.przywara@arm.com/
>> [2] https://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
>> [3] https://github.com/jernejsk/u-boot/commits/h616-v1
>> [4] https://github.com/apritzel/arm-trusted-firmware/commits/h616-WIP
>>
>> Changelog v1 .. v2:
>> - pinctrl: adjust irq bank map to cover undocumented GPIO bank IRQs
>> - use differing h_i2s0 pin output names
>> - r-ccu: fix number of used clocks
>> - ccu: remove PLL-PERIPHy(4X)
>> - ccu: fix gpu1 divider range
>> - ccu: fix usb-phy3 parent
>> - ccu: add missing TV clocks
>> - ccu: rework to CLK_OF_DECLARE style
>> - ccu: enable output bit for PLL clocks
>> - ccu: renumber clocks
>> - .dtsi: drop sun50i-a64-system-control fallback
>> - .dtsi: drop unknown SRAM regions
>> - .dtsi: add more (undocumented) GPIO interrupts
>> - .dtsi: fix I2C3 pin names
>> - .dtsi: use a100-emmc fallback for MMC2
>> - .dtsi: add second EMAC controller
>> - .dtsi: use H3 MUSB controller fallback
>> - .dtsi: fix frame size for USB PHY PMU registers
>> - .dtsi: add USB0 PHY references
>> - .dtsi: fix IR controller clock source
>> - .dts: fix LED naming and swap pins
>> - .dts: use 5V supply parent for USB supply
>> - .dts: drop dummy IRQ for AXP
>> - .dts: enable 3V3 header pin power rail
>> - .dts: add SPI flash node
>> - .dts: make USB-C port peripheral only
>> - add IRQ-less AXP support
>> - add two patches to support more than one EMAC clock
>> - add patch to rework and extend USB PHY support
>> - add DT binding documentation patches
>>
>> Andre Przywara (18):
>> clk: sunxi-ng: h6: Fix clock divider range on some clocks
>> dt-bindings: pinctrl: Add Allwinner H616 compatible strings
>> pinctrl: sunxi: Add support for the Allwinner H616 pin controller
>> pinctrl: sunxi: Add support for the Allwinner H616-R pin controller
>> dt-bindings: clk: sunxi-ccu: Add compatible string for Allwinner
>> H616
>> clk: sunxi-ng: Add support for the Allwinner H616 R-CCU
>> clk: sunxi-ng: Add support for the Allwinner H616 CCU
>> mfd: axp20x: Allow AXP chips without interrupt lines
>> dt-bindings: sram: sunxi-sram: Add H616 compatible string
>> soc: sunxi: sram: Add support for more than one EMAC clock
>> net: stmmac: dwmac-sun8i: Prepare for second EMAC clock register
>> phy: sun4i-usb: Rework "pmu_unk1" handling
>> phy: sun4i-usb: Add support for the H616 USB PHY
>> dt-bindings: watchdog: sun4i: Add H616 compatible string
>> dt-bindings: allwinner: Add H616 compatible strings
>> arm64: dts: allwinner: Add Allwinner H616 .dtsi file
>> dt-bindings: arm: sunxi: Add OrangePi Zero 2 binding
>> arm64: dts: allwinner: Add OrangePi Zero 2 .dts
>>
>> Yangtao Li (3):
>> dt-bindings: mmc: sunxi: Add Allwinner A100 and H616 compatibles
>> mmc: sunxi: add support for A100 mmc controller
>> dt-bindings: watchdog: sun4i: Add A100 compatible
>>
>> .../devicetree/bindings/arm/sunxi.yaml | 5 +
>> .../clock/allwinner,sun4i-a10-ccu.yaml | 2 +
>> .../bindings/i2c/marvell,mv64xxx-i2c.yaml | 21 +-
>> .../media/allwinner,sun4i-a10-ir.yaml | 16 +-
>> .../bindings/mmc/allwinner,sun4i-a10-mmc.yaml | 8 +
>> .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml | 2 +
>> .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml | 3 +
>> .../bindings/spi/allwinner,sun6i-a31-spi.yaml | 1 +
>> .../allwinner,sun4i-a10-system-control.yaml | 1 +
>> .../watchdog/allwinner,sun4i-a10-wdt.yaml | 9 +-
>> arch/arm64/boot/dts/allwinner/Makefile | 1 +
>> .../allwinner/sun50i-h616-orangepi-zero2.dts | 240 ++++
>> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 715 ++++++++++
>> drivers/clk/sunxi-ng/Kconfig | 7 +-
>> drivers/clk/sunxi-ng/Makefile | 1 +
>> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.c | 47 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h6-r.h | 3 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h6.c | 8 +-
>> drivers/clk/sunxi-ng/ccu-sun50i-h616.c | 1150
>> +++++++++++++++++
>> drivers/clk/sunxi-ng/ccu-sun50i-h616.h | 56 +
>> drivers/mfd/axp20x.c | 17 +-
>> drivers/mmc/host/sunxi-mmc.c | 28 +-
>> .../net/ethernet/stmicro/stmmac/dwmac-sun8i.c | 12 +-
>> drivers/phy/allwinner/phy-sun4i-usb.c | 39 +-
>> drivers/pinctrl/sunxi/Kconfig | 10 +
>> drivers/pinctrl/sunxi/Makefile | 2 +
>> drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c | 54 +
>> drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c | 548 ++++++++
>> drivers/soc/sunxi/sunxi_sram.c | 31 +-
>> include/dt-bindings/clock/sun50i-h616-ccu.h | 115 ++
>> include/dt-bindings/reset/sun50i-h616-ccu.h | 70 +
>> 31 files changed, 3151 insertions(+), 71 deletions(-)
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-
>> orangepi-zero2.dts
>> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.c
>> create mode 100644 drivers/clk/sunxi-ng/ccu-sun50i-h616.h
>> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616-r.c
>> create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun50i-h616.c
>> create mode 100644 include/dt-bindings/clock/sun50i-h616-ccu.h
>> create mode 100644 include/dt-bindings/reset/sun50i-h616-ccu.h
>>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 98+ messages in thread