[PATCH 0/7] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings

[PATCH 0/7] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings

[Nishanth Menon]

Hi,

This is one part of cleanups meant for make W=2 dtbs for 5.10 on TI
dtbs. Hopefully we dont see node_name_chars_strict warnings anymore.

As part of this cleanup, I ran a cross check of nodes that are
part of K3 as of right now, Vs what is "generic" definition as per 0.3
dt specification:
https://pastebin.ubuntu.com/p/kp3g4ktBYp/

I dont think the remaining have a good reference, at least in my
subjective view.

In possibly some cases, bootloaders may need to sync before doing DT
fixup etc.

Nishanth Menon (7):
  arm64: dts: ti: k3-am65*: Use generic gpio for node names
  arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name
  arm64: dts: ti: k3-*: Use generic pinctrl for node names
  arm64: dts: ti: k3-am65-base-board Use generic camera for node name
    instead of ov5640
  arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
    node name
  arm64: dts: ti: k3-*: Use generic adc for node names
  arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  8 ++++----
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi     |  6 +++---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 18 +++++++++---------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  8 ++++----
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 9 files changed, 49 insertions(+), 49 deletions(-)

-- 
2.17.1

[PATCH 0/7] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings

[Nishanth Menon]

Hi,

This is one part of cleanups meant for make W=2 dtbs for 5.10 on TI
dtbs. Hopefully we dont see node_name_chars_strict warnings anymore.

As part of this cleanup, I ran a cross check of nodes that are
part of K3 as of right now, Vs what is "generic" definition as per 0.3
dt specification:
https://pastebin.ubuntu.com/p/kp3g4ktBYp/

I dont think the remaining have a good reference, at least in my
subjective view.

In possibly some cases, bootloaders may need to sync before doing DT
fixup etc.

Nishanth Menon (7):
  arm64: dts: ti: k3-am65*: Use generic gpio for node names
  arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name
  arm64: dts: ti: k3-*: Use generic pinctrl for node names
  arm64: dts: ti: k3-am65-base-board Use generic camera for node name
    instead of ov5640
  arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
    node name
  arm64: dts: ti: k3-*: Use generic adc for node names
  arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  8 ++++----
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi     |  6 +++---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 18 +++++++++---------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  8 ++++----
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  8 ++++----
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 9 files changed, 49 insertions(+), 49 deletions(-)

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/7] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Nishanth Menon]

Use gpio@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 76e0edc4ad5c..336d09d6fec7 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -661,7 +661,7 @@
 		};
 	};
 
-	main_gpio0:  main_gpio0@600000 {
+	main_gpio0: gpio@600000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x600000 0x0 0x100>;
 		gpio-controller;
@@ -676,7 +676,7 @@
 		clock-names = "gpio";
 	};
 
-	main_gpio1:  main_gpio1@601000 {
+	main_gpio1: gpio@601000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x601000 0x0 0x100>;
 		gpio-controller;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index a1ffe88d9664..0765700a8ba8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -80,7 +80,7 @@
 		ti,interrupt-ranges = <0 712 16>;
 	};
 
-	wkup_gpio0: wkup_gpio0@42110000 {
+	wkup_gpio0: gpio@42110000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x42110000 0x100>;
 		gpio-controller;
-- 
2.17.1

[PATCH 1/7] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Nishanth Menon]

Use gpio@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 76e0edc4ad5c..336d09d6fec7 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -661,7 +661,7 @@
 		};
 	};
 
-	main_gpio0:  main_gpio0@600000 {
+	main_gpio0: gpio@600000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x600000 0x0 0x100>;
 		gpio-controller;
@@ -676,7 +676,7 @@
 		clock-names = "gpio";
 	};
 
-	main_gpio1:  main_gpio1@601000 {
+	main_gpio1: gpio@601000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x601000 0x0 0x100>;
 		gpio-controller;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index a1ffe88d9664..0765700a8ba8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -80,7 +80,7 @@
 		ti,interrupt-ranges = <0 712 16>;
 	};
 
-	wkup_gpio0: wkup_gpio0@42110000 {
+	wkup_gpio0: gpio@42110000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x42110000 0x100>;
 		gpio-controller;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 1/7] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use gpio@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  2 files changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 76e0edc4ad5c..336d09d6fec7 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -661,7 +661,7 @@
>  		};
>  	};
>  
> -	main_gpio0:  main_gpio0@600000 {
> +	main_gpio0: gpio@600000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x0 0x600000 0x0 0x100>;
>  		gpio-controller;
> @@ -676,7 +676,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	main_gpio1:  main_gpio1@601000 {
> +	main_gpio1: gpio@601000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x0 0x601000 0x0 0x100>;
>  		gpio-controller;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index a1ffe88d9664..0765700a8ba8 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -80,7 +80,7 @@
>  		ti,interrupt-ranges = <0 712 16>;
>  	};
>  
> -	wkup_gpio0: wkup_gpio0@42110000 {
> +	wkup_gpio0: gpio@42110000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x42110000 0x100>;
>  		gpio-controller;
> 

Re: [PATCH 1/7] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use gpio@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  2 files changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 76e0edc4ad5c..336d09d6fec7 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -661,7 +661,7 @@
>  		};
>  	};
>  
> -	main_gpio0:  main_gpio0@600000 {
> +	main_gpio0: gpio@600000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x0 0x600000 0x0 0x100>;
>  		gpio-controller;
> @@ -676,7 +676,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	main_gpio1:  main_gpio1@601000 {
> +	main_gpio1: gpio@601000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x0 0x601000 0x0 0x100>;
>  		gpio-controller;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index a1ffe88d9664..0765700a8ba8 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -80,7 +80,7 @@
>  		ti,interrupt-ranges = <0 712 16>;
>  	};
>  
> -	wkup_gpio0: wkup_gpio0@42110000 {
> +	wkup_gpio0: gpio@42110000 {
>  		compatible = "ti,am654-gpio", "ti,keystone-gpio";
>  		reg = <0x42110000 0x100>;
>  		gpio-controller;
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Nishanth Menon]

Use clock@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 336d09d6fec7..03e28fc256de 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -327,12 +327,12 @@
 			reg = <0x00000210 0x4>;
 		};
 
-		serdes0_clk: serdes_clk@4080 {
+		serdes0_clk: clock@4080 {
 			compatible = "syscon";
 			reg = <0x00004080 0x4>;
 		};
 
-		serdes1_clk: serdes_clk@4090 {
+		serdes1_clk: clock@4090 {
 			compatible = "syscon";
 			reg = <0x00004090 0x4>;
 		};
-- 
2.17.1

[PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Nishanth Menon]

Use clock@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 336d09d6fec7..03e28fc256de 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -327,12 +327,12 @@
 			reg = <0x00000210 0x4>;
 		};
 
-		serdes0_clk: serdes_clk@4080 {
+		serdes0_clk: clock@4080 {
 			compatible = "syscon";
 			reg = <0x00004080 0x4>;
 		};
 
-		serdes1_clk: serdes_clk@4090 {
+		serdes1_clk: clock@4090 {
 			compatible = "syscon";
 			reg = <0x00004090 0x4>;
 		};
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use clock@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 336d09d6fec7..03e28fc256de 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -327,12 +327,12 @@
>  			reg = <0x00000210 0x4>;
>  		};
>  
> -		serdes0_clk: serdes_clk@4080 {
> +		serdes0_clk: clock@4080 {
>  			compatible = "syscon";
>  			reg = <0x00004080 0x4>;
>  		};
>  
> -		serdes1_clk: serdes_clk@4090 {
> +		serdes1_clk: clock@4090 {
>  			compatible = "syscon";
>  			reg = <0x00004090 0x4>;
>  		};
> 

Btw, there is also ehrpwm_tbclk alongside these nodes which is currently defined
as a syscon, but is actually a clock.

regards
Suman

Re: [PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use clock@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 336d09d6fec7..03e28fc256de 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -327,12 +327,12 @@
>  			reg = <0x00000210 0x4>;
>  		};
>  
> -		serdes0_clk: serdes_clk@4080 {
> +		serdes0_clk: clock@4080 {
>  			compatible = "syscon";
>  			reg = <0x00004080 0x4>;
>  		};
>  
> -		serdes1_clk: serdes_clk@4090 {
> +		serdes1_clk: clock@4090 {
>  			compatible = "syscon";
>  			reg = <0x00004090 0x4>;
>  		};
> 

Btw, there is also ehrpwm_tbclk alongside these nodes which is currently defined
as a syscon, but is actually a clock.

regards
Suman


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Nishanth Menon]

On 12:45-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use clock@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> 
> Acked-by: Suman Anna <s-anna@ti.com>
> 
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
> >  1 file changed, 2 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > index 336d09d6fec7..03e28fc256de 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > @@ -327,12 +327,12 @@
> >  			reg = <0x00000210 0x4>;
> >  		};
> >  
> > -		serdes0_clk: serdes_clk@4080 {
> > +		serdes0_clk: clock@4080 {
> >  			compatible = "syscon";
> >  			reg = <0x00004080 0x4>;
> >  		};
> >  
> > -		serdes1_clk: serdes_clk@4090 {
> > +		serdes1_clk: clock@4090 {
> >  			compatible = "syscon";
> >  			reg = <0x00004090 0x4>;
> >  		};
> > 
> 
> Btw, there is also ehrpwm_tbclk alongside these nodes which is currently defined
> as a syscon, but is actually a clock.

aah, good catch.. I can fix that in the follow on V2.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 2/7] arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name

[Nishanth Menon]

On 12:45-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use clock@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> 
> Acked-by: Suman Anna <s-anna@ti.com>
> 
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
> >  1 file changed, 2 insertions(+), 2 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > index 336d09d6fec7..03e28fc256de 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > @@ -327,12 +327,12 @@
> >  			reg = <0x00000210 0x4>;
> >  		};
> >  
> > -		serdes0_clk: serdes_clk@4080 {
> > +		serdes0_clk: clock@4080 {
> >  			compatible = "syscon";
> >  			reg = <0x00004080 0x4>;
> >  		};
> >  
> > -		serdes1_clk: serdes_clk@4090 {
> > +		serdes1_clk: clock@4090 {
> >  			compatible = "syscon";
> >  			reg = <0x00004090 0x4>;
> >  		};
> > 
> 
> Btw, there is also ehrpwm_tbclk alongside these nodes which is currently defined
> as a syscon, but is actually a clock.

aah, good catch.. I can fix that in the follow on V2.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/7] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Nishanth Menon]

Use pinctrl@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 03e28fc256de..9c96e3f58c86 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -134,7 +134,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c000 0x0 0x2e4>;
 		#pinctrl-cells = <1>;
@@ -142,7 +142,7 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
-	main_pmx1: pinmux@11c2e8 {
+	main_pmx1: pinctrl@11c2e8 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c2e8 0x0 0x24>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 0765700a8ba8..bb498be2f0a4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -39,7 +39,7 @@
 		reg = <0x43000014 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		reg = <0x4301c000 0x118>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 00a36a14efe7..1d2a7c05b6f3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -327,7 +327,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x0 0x11c000 0x0 0x2b4>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index c4a48e8d420a..9ad0266598ad 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -53,7 +53,7 @@
 		reg = <0x0 0x43000014 0x0 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x178>;
-- 
2.17.1

[PATCH 3/7] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Nishanth Menon]

Use pinctrl@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 03e28fc256de..9c96e3f58c86 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -134,7 +134,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c000 0x0 0x2e4>;
 		#pinctrl-cells = <1>;
@@ -142,7 +142,7 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
-	main_pmx1: pinmux@11c2e8 {
+	main_pmx1: pinctrl@11c2e8 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c2e8 0x0 0x24>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 0765700a8ba8..bb498be2f0a4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -39,7 +39,7 @@
 		reg = <0x43000014 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		reg = <0x4301c000 0x118>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 00a36a14efe7..1d2a7c05b6f3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -327,7 +327,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x0 0x11c000 0x0 0x2b4>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index c4a48e8d420a..9ad0266598ad 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -53,7 +53,7 @@
 		reg = <0x0 0x43000014 0x0 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x178>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 3/7] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use pinctrl@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
>  4 files changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 03e28fc256de..9c96e3f58c86 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -134,7 +134,7 @@
>  		};
>  	};
>  
> -	main_pmx0: pinmux@11c000 {
> +	main_pmx0: pinctrl@11c000 {
>  		compatible = "pinctrl-single";
>  		reg = <0x0 0x11c000 0x0 0x2e4>;
>  		#pinctrl-cells = <1>;
> @@ -142,7 +142,7 @@
>  		pinctrl-single,function-mask = <0xffffffff>;
>  	};
>  
> -	main_pmx1: pinmux@11c2e8 {
> +	main_pmx1: pinctrl@11c2e8 {
>  		compatible = "pinctrl-single";
>  		reg = <0x0 0x11c2e8 0x0 0x24>;
>  		#pinctrl-cells = <1>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index 0765700a8ba8..bb498be2f0a4 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -39,7 +39,7 @@
>  		reg = <0x43000014 0x4>;
>  	};
>  
> -	wkup_pmx0: pinmux@4301c000 {
> +	wkup_pmx0: pinctrl@4301c000 {
>  		compatible = "pinctrl-single";
>  		reg = <0x4301c000 0x118>;
>  		#pinctrl-cells = <1>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 00a36a14efe7..1d2a7c05b6f3 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -327,7 +327,7 @@
>  		};
>  	};
>  
> -	main_pmx0: pinmux@11c000 {
> +	main_pmx0: pinctrl@11c000 {
>  		compatible = "pinctrl-single";
>  		/* Proxy 0 addressing */
>  		reg = <0x0 0x11c000 0x0 0x2b4>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index c4a48e8d420a..9ad0266598ad 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -53,7 +53,7 @@
>  		reg = <0x0 0x43000014 0x0 0x4>;
>  	};
>  
> -	wkup_pmx0: pinmux@4301c000 {
> +	wkup_pmx0: pinctrl@4301c000 {
>  		compatible = "pinctrl-single";
>  		/* Proxy 0 addressing */
>  		reg = <0x00 0x4301c000 0x00 0x178>;
> 

Re: [PATCH 3/7] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use pinctrl@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
>  4 files changed, 5 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 03e28fc256de..9c96e3f58c86 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -134,7 +134,7 @@
>  		};
>  	};
>  
> -	main_pmx0: pinmux@11c000 {
> +	main_pmx0: pinctrl@11c000 {
>  		compatible = "pinctrl-single";
>  		reg = <0x0 0x11c000 0x0 0x2e4>;
>  		#pinctrl-cells = <1>;
> @@ -142,7 +142,7 @@
>  		pinctrl-single,function-mask = <0xffffffff>;
>  	};
>  
> -	main_pmx1: pinmux@11c2e8 {
> +	main_pmx1: pinctrl@11c2e8 {
>  		compatible = "pinctrl-single";
>  		reg = <0x0 0x11c2e8 0x0 0x24>;
>  		#pinctrl-cells = <1>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index 0765700a8ba8..bb498be2f0a4 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -39,7 +39,7 @@
>  		reg = <0x43000014 0x4>;
>  	};
>  
> -	wkup_pmx0: pinmux@4301c000 {
> +	wkup_pmx0: pinctrl@4301c000 {
>  		compatible = "pinctrl-single";
>  		reg = <0x4301c000 0x118>;
>  		#pinctrl-cells = <1>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 00a36a14efe7..1d2a7c05b6f3 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -327,7 +327,7 @@
>  		};
>  	};
>  
> -	main_pmx0: pinmux@11c000 {
> +	main_pmx0: pinctrl@11c000 {
>  		compatible = "pinctrl-single";
>  		/* Proxy 0 addressing */
>  		reg = <0x0 0x11c000 0x0 0x2b4>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index c4a48e8d420a..9ad0266598ad 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -53,7 +53,7 @@
>  		reg = <0x0 0x43000014 0x0 0x4>;
>  	};
>  
> -	wkup_pmx0: pinmux@4301c000 {
> +	wkup_pmx0: pinctrl@4301c000 {
>  		compatible = "pinctrl-single";
>  		/* Proxy 0 addressing */
>  		reg = <0x00 0x4301c000 0x00 0x178>;
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/7] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Nishanth Menon]

Use camera@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index b8a8a0fcb8af..86c9074cb070 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -257,7 +257,7 @@
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
 
-	ov5640@3c {
+	ov5640: camera@3c {
 		compatible = "ovti,ov5640";
 		reg = <0x3c>;
 
-- 
2.17.1

[PATCH 4/7] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Nishanth Menon]

Use camera@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index b8a8a0fcb8af..86c9074cb070 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -257,7 +257,7 @@
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
 
-	ov5640@3c {
+	ov5640: camera@3c {
 		compatible = "ovti,ov5640";
 		reg = <0x3c>;
 
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 4/7] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use camera@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index b8a8a0fcb8af..86c9074cb070 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -257,7 +257,7 @@
>  	pinctrl-0 = <&main_i2c1_pins_default>;
>  	clock-frequency = <400000>;
>  
> -	ov5640@3c {
> +	ov5640: camera@3c {
>  		compatible = "ovti,ov5640";
>  		reg = <0x3c>;
>  
> 

Re: [PATCH 4/7] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use camera@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index b8a8a0fcb8af..86c9074cb070 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -257,7 +257,7 @@
>  	pinctrl-0 = <&main_i2c1_pins_default>;
>  	clock-frequency = <400000>;
>  
> -	ov5640@3c {
> +	ov5640: camera@3c {
>  		compatible = "ovti,ov5640";
>  		reg = <0x3c>;
>  
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

Use temperature-sensor@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index bb498be2f0a4..ed42f13e7663 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -95,7 +95,7 @@
 		clock-names = "gpio";
 	};
 
-	wkup_vtm0: thermal@42050000 {
+	wkup_vtm0: temperature-sensor@42050000 {
 		compatible = "ti,am654-vtm";
 		reg = <0x42050000 0x25c>;
 		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
-- 
2.17.1

[PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

Use temperature-sensor@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index bb498be2f0a4..ed42f13e7663 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -95,7 +95,7 @@
 		clock-names = "gpio";
 	};
 
-	wkup_vtm0: thermal@42050000 {
+	wkup_vtm0: temperature-sensor@42050000 {
 		compatible = "ti,am654-vtm";
 		reg = <0x42050000 0x25c>;
 		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use temperature-sensor@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index bb498be2f0a4..ed42f13e7663 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -95,7 +95,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	wkup_vtm0: thermal@42050000 {
> +	wkup_vtm0: temperature-sensor@42050000 {

There has been a suggestion to use something like thermal-sensor during the
bindings review, but it is better to use this standard node name.

Reviewed-by: Suman Anna <s-anna@ti.com>

regards
Suman

>  		compatible = "ti,am654-vtm";
>  		reg = <0x42050000 0x25c>;
>  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> 

Re: [PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use temperature-sensor@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index bb498be2f0a4..ed42f13e7663 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -95,7 +95,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	wkup_vtm0: thermal@42050000 {
> +	wkup_vtm0: temperature-sensor@42050000 {

There has been a suggestion to use something like thermal-sensor during the
bindings review, but it is better to use this standard node name.

Reviewed-by: Suman Anna <s-anna@ti.com>

regards
Suman

>  		compatible = "ti,am654-vtm";
>  		reg = <0x42050000 0x25c>;
>  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

On 11:55-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use temperature-sensor@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > index bb498be2f0a4..ed42f13e7663 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > @@ -95,7 +95,7 @@
> >  		clock-names = "gpio";
> >  	};
> >  
> > -	wkup_vtm0: thermal@42050000 {
> > +	wkup_vtm0: temperature-sensor@42050000 {
> 
> There has been a suggestion to use something like thermal-sensor during the
> bindings review, but it is better to use this standard node name.

Yes - I did notice it as well, and then picked up the recommendation
straight from 0.3 spec itself.
> 
> Reviewed-by: Suman Anna <s-anna@ti.com>
> 
> regards
> Suman
> 
> >  		compatible = "ti,am654-vtm";
> >  		reg = <0x42050000 0x25c>;
> >  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> > 
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 5/7] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

On 11:55-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use temperature-sensor@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
> >  1 file changed, 1 insertion(+), 1 deletion(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > index bb498be2f0a4..ed42f13e7663 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> > @@ -95,7 +95,7 @@
> >  		clock-names = "gpio";
> >  	};
> >  
> > -	wkup_vtm0: thermal@42050000 {
> > +	wkup_vtm0: temperature-sensor@42050000 {
> 
> There has been a suggestion to use something like thermal-sensor during the
> bindings review, but it is better to use this standard node name.

Yes - I did notice it as well, and then picked up the recommendation
straight from 0.3 spec itself.
> 
> Reviewed-by: Suman Anna <s-anna@ti.com>
> 
> regards
> Suman
> 
> >  		compatible = "ti,am654-vtm";
> >  		reg = <0x42050000 0x25c>;
> >  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> > 
> 

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

Use adc@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 51ca4b4d4c21..6dfec68ac865 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -80,7 +80,7 @@
 		#size-cells = <0>;
 	};
 
-	tscadc0: tscadc@40200000 {
+	tscadc0: adc@40200000 {
 		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
 		reg = <0x0 0x40200000 0x0 0x1000>;
 		interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
@@ -98,7 +98,7 @@
 		};
 	};
 
-	tscadc1: tscadc@40210000 {
+	tscadc1: adc@40210000 {
 		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
 		reg = <0x0 0x40210000 0x0 0x1000>;
 		interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 9ad0266598ad..81801f519a61 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -211,7 +211,7 @@
 		};
 	};
 
-	tscadc0: tscadc@40200000 {
+	tscadc0: adc@40200000 {
 		compatible = "ti,am3359-tscadc";
 		reg = <0x0 0x40200000 0x0 0x1000>;
 		interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
@@ -230,7 +230,7 @@
 		};
 	};
 
-	tscadc1: tscadc@40210000 {
+	tscadc1: adc@40210000 {
 		compatible = "ti,am3359-tscadc";
 		reg = <0x0 0x40210000 0x0 0x1000>;
 		interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.17.1

[PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

Use adc@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 51ca4b4d4c21..6dfec68ac865 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -80,7 +80,7 @@
 		#size-cells = <0>;
 	};
 
-	tscadc0: tscadc@40200000 {
+	tscadc0: adc@40200000 {
 		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
 		reg = <0x0 0x40200000 0x0 0x1000>;
 		interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
@@ -98,7 +98,7 @@
 		};
 	};
 
-	tscadc1: tscadc@40210000 {
+	tscadc1: adc@40210000 {
 		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
 		reg = <0x0 0x40210000 0x0 0x1000>;
 		interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 9ad0266598ad..81801f519a61 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -211,7 +211,7 @@
 		};
 	};
 
-	tscadc0: tscadc@40200000 {
+	tscadc0: adc@40200000 {
 		compatible = "ti,am3359-tscadc";
 		reg = <0x0 0x40200000 0x0 0x1000>;
 		interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
@@ -230,7 +230,7 @@
 		};
 	};
 
-	tscadc1: tscadc@40210000 {
+	tscadc1: adc@40210000 {
 		compatible = "ti,am3359-tscadc";
 		reg = <0x0 0x40210000 0x0 0x1000>;
 		interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use adc@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
>  2 files changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> index 51ca4b4d4c21..6dfec68ac865 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> @@ -80,7 +80,7 @@
>  		#size-cells = <0>;
>  	};
>  
> -	tscadc0: tscadc@40200000 {
> +	tscadc0: adc@40200000 {

OK with these changes, since these seem to be only have the adc child nodes.
This node is essentially a parent node for touchscreen and adc child nodes. The
driver is currently looking for "tsc" on touchscreen child nodes, but none of
the K3 SoCs have them atm.

regards
Suman

>  		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
>  		reg = <0x0 0x40200000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
> @@ -98,7 +98,7 @@
>  		};
>  	};
>  
> -	tscadc1: tscadc@40210000 {
> +	tscadc1: adc@40210000 {
>  		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
>  		reg = <0x0 0x40210000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 9ad0266598ad..81801f519a61 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -211,7 +211,7 @@
>  		};
>  	};
>  
> -	tscadc0: tscadc@40200000 {
> +	tscadc0: adc@40200000 {
>  		compatible = "ti,am3359-tscadc";
>  		reg = <0x0 0x40200000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
> @@ -230,7 +230,7 @@
>  		};
>  	};
>  
> -	tscadc1: tscadc@40210000 {
> +	tscadc1: adc@40210000 {
>  		compatible = "ti,am3359-tscadc";
>  		reg = <0x0 0x40210000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
> 

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Use adc@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
>  2 files changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> index 51ca4b4d4c21..6dfec68ac865 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> @@ -80,7 +80,7 @@
>  		#size-cells = <0>;
>  	};
>  
> -	tscadc0: tscadc@40200000 {
> +	tscadc0: adc@40200000 {

OK with these changes, since these seem to be only have the adc child nodes.
This node is essentially a parent node for touchscreen and adc child nodes. The
driver is currently looking for "tsc" on touchscreen child nodes, but none of
the K3 SoCs have them atm.

regards
Suman

>  		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
>  		reg = <0x0 0x40200000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
> @@ -98,7 +98,7 @@
>  		};
>  	};
>  
> -	tscadc1: tscadc@40210000 {
> +	tscadc1: adc@40210000 {
>  		compatible = "ti,am654-tscadc", "ti,am3359-tscadc";
>  		reg = <0x0 0x40210000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 9ad0266598ad..81801f519a61 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -211,7 +211,7 @@
>  		};
>  	};
>  
> -	tscadc0: tscadc@40200000 {
> +	tscadc0: adc@40200000 {
>  		compatible = "ti,am3359-tscadc";
>  		reg = <0x0 0x40200000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
> @@ -230,7 +230,7 @@
>  		};
>  	};
>  
> -	tscadc1: tscadc@40210000 {
> +	tscadc1: adc@40210000 {
>  		compatible = "ti,am3359-tscadc";
>  		reg = <0x0 0x40210000 0x0 0x1000>;
>  		interrupts = <GIC_SPI 861 IRQ_TYPE_LEVEL_HIGH>;
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

On 11:51-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use adc@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
> >  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
> >  2 files changed, 4 insertions(+), 4 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > index 51ca4b4d4c21..6dfec68ac865 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > @@ -80,7 +80,7 @@
> >  		#size-cells = <0>;
> >  	};
> >  
> > -	tscadc0: tscadc@40200000 {
> > +	tscadc0: adc@40200000 {
> 
> OK with these changes, since these seem to be only have the adc child nodes.
> This node is essentially a parent node for touchscreen and adc child nodes. The
> driver is currently looking for "tsc" on touchscreen child nodes, but none of
> the K3 SoCs have them atm.
> 


Vignesh: are you ok with this, care to comment?

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

On 11:51-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Use adc@ naming for nodes following standard conventions of device
> > tree (section 2.2.2 Generic Names recommendation in [1]).
> > 
> > [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> > 
> > Suggested-by: Suman Anna <s-anna@ti.com>
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
> >  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
> >  2 files changed, 4 insertions(+), 4 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > index 51ca4b4d4c21..6dfec68ac865 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> > @@ -80,7 +80,7 @@
> >  		#size-cells = <0>;
> >  	};
> >  
> > -	tscadc0: tscadc@40200000 {
> > +	tscadc0: adc@40200000 {
> 
> OK with these changes, since these seem to be only have the adc child nodes.
> This node is essentially a parent node for touchscreen and adc child nodes. The
> driver is currently looking for "tsc" on touchscreen child nodes, but none of
> the K3 SoCs have them atm.
> 


Vignesh: are you ok with this, care to comment?

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Vignesh Raghavendra]

Hi Nishanth,

On 9/2/20 11:48 PM, Nishanth Menon wrote:
> On 11:51-20200902, Suman Anna wrote:
>> On 9/1/20 5:30 PM, Nishanth Menon wrote:
>>> Use adc@ naming for nodes following standard conventions of device
>>> tree (section 2.2.2 Generic Names recommendation in [1]).
>>>
>>> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
>>>
>>> Suggested-by: Suman Anna <s-anna@ti.com>
>>> Signed-off-by: Nishanth Menon <nm@ti.com>
>>> ---
>>>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
>>>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
>>>  2 files changed, 4 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> index 51ca4b4d4c21..6dfec68ac865 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> @@ -80,7 +80,7 @@
>>>  		#size-cells = <0>;
>>>  	};
>>>  
>>> -	tscadc0: tscadc@40200000 {
>>> +	tscadc0: adc@40200000 {
>>
>> OK with these changes, since these seem to be only have the adc child nodes.
>> This node is essentially a parent node for touchscreen and adc child nodes. The
>> driver is currently looking for "tsc" on touchscreen child nodes, but none of
>> the K3 SoCs have them atm.
>>
> 
> 
> Vignesh: are you ok with this, care to comment?
> 

On K3 SoCs, ADC IP is reuse from AM335x but just lacks resistive
touchscreen interfaces. So, existing AM335x ADC driver is being reused
for K3 devices as well. Unfortunately, ADC driver cannot be used as
standalone and is dependent on MFD parent to be present...
Above node represents the MFD parent and ADC itself is the child node
(see arch/arm64/boot/dts/ti/k3-am654-base-board.dts). So, I recommend
that we keep this node's name as tscadc in order to avoid having same
name for parent and child node which will be quite confusing.

Regards
Vignesh

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Vignesh Raghavendra]

Hi Nishanth,

On 9/2/20 11:48 PM, Nishanth Menon wrote:
> On 11:51-20200902, Suman Anna wrote:
>> On 9/1/20 5:30 PM, Nishanth Menon wrote:
>>> Use adc@ naming for nodes following standard conventions of device
>>> tree (section 2.2.2 Generic Names recommendation in [1]).
>>>
>>> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
>>>
>>> Suggested-by: Suman Anna <s-anna@ti.com>
>>> Signed-off-by: Nishanth Menon <nm@ti.com>
>>> ---
>>>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
>>>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
>>>  2 files changed, 4 insertions(+), 4 deletions(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> index 51ca4b4d4c21..6dfec68ac865 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
>>> @@ -80,7 +80,7 @@
>>>  		#size-cells = <0>;
>>>  	};
>>>  
>>> -	tscadc0: tscadc@40200000 {
>>> +	tscadc0: adc@40200000 {
>>
>> OK with these changes, since these seem to be only have the adc child nodes.
>> This node is essentially a parent node for touchscreen and adc child nodes. The
>> driver is currently looking for "tsc" on touchscreen child nodes, but none of
>> the K3 SoCs have them atm.
>>
> 
> 
> Vignesh: are you ok with this, care to comment?
> 

On K3 SoCs, ADC IP is reuse from AM335x but just lacks resistive
touchscreen interfaces. So, existing AM335x ADC driver is being reused
for K3 devices as well. Unfortunately, ADC driver cannot be used as
standalone and is dependent on MFD parent to be present...
Above node represents the MFD parent and ADC itself is the child node
(see arch/arm64/boot/dts/ti/k3-am654-base-board.dts). So, I recommend
that we keep this node's name as tscadc in order to avoid having same
name for parent and child node which will be quite confusing.

Regards
Vignesh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

On 10:55-20200903, Vignesh Raghavendra wrote:
> Hi Nishanth,
> 
> On 9/2/20 11:48 PM, Nishanth Menon wrote:
> > On 11:51-20200902, Suman Anna wrote:
> >> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> >>> Use adc@ naming for nodes following standard conventions of device
> >>> tree (section 2.2.2 Generic Names recommendation in [1]).
> >>>
> >>> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> >>>
> >>> Suggested-by: Suman Anna <s-anna@ti.com>
> >>> Signed-off-by: Nishanth Menon <nm@ti.com>
> >>> ---
> >>>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
> >>>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
> >>>  2 files changed, 4 insertions(+), 4 deletions(-)
> >>>
> >>> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> index 51ca4b4d4c21..6dfec68ac865 100644
> >>> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> @@ -80,7 +80,7 @@
> >>>  		#size-cells = <0>;
> >>>  	};
> >>>  
> >>> -	tscadc0: tscadc@40200000 {
> >>> +	tscadc0: adc@40200000 {
> >>
> >> OK with these changes, since these seem to be only have the adc child nodes.
> >> This node is essentially a parent node for touchscreen and adc child nodes. The
> >> driver is currently looking for "tsc" on touchscreen child nodes, but none of
> >> the K3 SoCs have them atm.
> >>
> > 
> > 
> > Vignesh: are you ok with this, care to comment?
> > 
> 
> On K3 SoCs, ADC IP is reuse from AM335x but just lacks resistive
> touchscreen interfaces. So, existing AM335x ADC driver is being reused
> for K3 devices as well. Unfortunately, ADC driver cannot be used as
> standalone and is dependent on MFD parent to be present...
> Above node represents the MFD parent and ADC itself is the child node
> (see arch/arm64/boot/dts/ti/k3-am654-base-board.dts). So, I recommend
> that we keep this node's name as tscadc in order to avoid having same
> name for parent and child node which will be quite confusing.


Thanks for your feedback. I will drop this patch.
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 6/7] arm64: dts: ti: k3-*: Use generic adc for node names

[Nishanth Menon]

On 10:55-20200903, Vignesh Raghavendra wrote:
> Hi Nishanth,
> 
> On 9/2/20 11:48 PM, Nishanth Menon wrote:
> > On 11:51-20200902, Suman Anna wrote:
> >> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> >>> Use adc@ naming for nodes following standard conventions of device
> >>> tree (section 2.2.2 Generic Names recommendation in [1]).
> >>>
> >>> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> >>>
> >>> Suggested-by: Suman Anna <s-anna@ti.com>
> >>> Signed-off-by: Nishanth Menon <nm@ti.com>
> >>> ---
> >>>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi         | 4 ++--
> >>>  arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 4 ++--
> >>>  2 files changed, 4 insertions(+), 4 deletions(-)
> >>>
> >>> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> index 51ca4b4d4c21..6dfec68ac865 100644
> >>> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> >>> @@ -80,7 +80,7 @@
> >>>  		#size-cells = <0>;
> >>>  	};
> >>>  
> >>> -	tscadc0: tscadc@40200000 {
> >>> +	tscadc0: adc@40200000 {
> >>
> >> OK with these changes, since these seem to be only have the adc child nodes.
> >> This node is essentially a parent node for touchscreen and adc child nodes. The
> >> driver is currently looking for "tsc" on touchscreen child nodes, but none of
> >> the K3 SoCs have them atm.
> >>
> > 
> > 
> > Vignesh: are you ok with this, care to comment?
> > 
> 
> On K3 SoCs, ADC IP is reuse from AM335x but just lacks resistive
> touchscreen interfaces. So, existing AM335x ADC driver is being reused
> for K3 devices as well. Unfortunately, ADC driver cannot be used as
> standalone and is dependent on MFD parent to be present...
> Above node represents the MFD parent and ADC itself is the child node
> (see arch/arm64/boot/dts/ti/k3-am654-base-board.dts). So, I recommend
> that we keep this node's name as tscadc in order to avoid having same
> name for parent and child node which will be quite confusing.


Thanks for your feedback. I will drop this patch.
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Nishanth Menon]

Building with W=2 throws up a bunch of easy to fixup errors..
node_name_chars_strict is one of them.. Knock those out.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 8 files changed, 33 insertions(+), 33 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 9c96e3f58c86..ff3e38408dbc 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -305,7 +305,7 @@
 		no-1-8-v;
 	};
 
-	scm_conf: scm_conf@100000 {
+	scm_conf: scm-conf@100000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0 0x00100000 0 0x1c000>;
 		#address-cells = <1>;
@@ -344,7 +344,7 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
+		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
 			compatible = "syscon";
 			reg = <0x0000041E0 0x14>;
 		};
@@ -445,7 +445,7 @@
 		ti,interrupt-ranges = <0 392 32>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 6dfec68ac865..435e51019287 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -6,7 +6,7 @@
  */
 
 &cbass_mcu {
-	mcu_conf: scm_conf@40f00000 {
+	mcu_conf: scm-conf@40f00000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0x0 0x40f00000 0x0 0x20000>;
 		#address-cells = <1>;
@@ -116,7 +116,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 86c9074cb070..d12dd89f3405 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -29,7 +29,7 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		secure_ddr: secure_ddr@9e800000 {
+		secure_ddr: secure-ddr@9e800000 {
 			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
 			alignment = <0x1000>;
 			no-map;
@@ -70,14 +70,14 @@
 		>;
 	};
 
-	push_button_pins_default: push_button__pins_default {
+	push_button_pins_default: push-button-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
 			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
 		>;
 	};
 
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
 			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
@@ -93,13 +93,13 @@
 		>;
 	};
 
-	wkup_pca554_default: wkup_pca554_default {
+	wkup_pca554_default: wkup-pca554-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
 			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
@@ -116,7 +116,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
 			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
 			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
@@ -180,7 +180,7 @@
 		>;
 	};
 
-	usb1_pins_default: usb1_pins_default {
+	usb1_pins_default: usb1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
 		>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
index cdc3d40c3f60..9021c738056b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
@@ -2,13 +2,13 @@
 
 #include <dt-bindings/thermal/thermal.h>
 
-mpu0_thermal: mpu0_thermal {
+mpu0_thermal: mpu0-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 0>;
 
 	trips {
-		mpu0_crit: mpu0_crit {
+		mpu0_crit: mpu0-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
 	};
 };
 
-mpu1_thermal: mpu1_thermal {
+mpu1_thermal: mpu1-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 1>;
 
 	trips {
-		mpu1_crit: mpu1_crit {
+		mpu1_crit: mpu1-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
 	};
 };
 
-mcu_thermal: mcu_thermal {
+mcu_thermal: mcu-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 2>;
 
 	trips {
-		mcu_crit: mcu_crit {
+		mcu_crit: mcu-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index c355692796a9..648267284582 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -86,13 +86,13 @@
 };
 
 &main_pmx0 {
-	sw10_button_pins_default: sw10_button_pins_default {
+	sw10_button_pins_default: sw10-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
 			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
@@ -106,14 +106,14 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main_usbss0_pins_default {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
 			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
-	main_usbss1_pins_default: main_usbss1_pins_default {
+	main_usbss1_pins_default: main-usbss1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
 		>;
@@ -153,7 +153,7 @@
 		>;
 	};
 
-	mcasp10_pins_default: mcasp10_pins_default {
+	mcasp10_pins_default: mcasp10-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
 			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
 		>;
@@ -175,7 +175,7 @@
 };
 
 &wkup_pmx0 {
-	sw11_button_pins_default: sw11_button_pins_default {
+	sw11_button_pins_default: sw11-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
 		>;
@@ -194,7 +194,7 @@
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
 			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
@@ -211,7 +211,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
 			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 1d2a7c05b6f3..ea57d07777ba 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -86,7 +86,7 @@
 		ti,interrupt-ranges = <8 392 56>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -888,7 +888,7 @@
 		no-1-8-v;
 	};
 
-	usbss0: cdns_usb@4104000 {
+	usbss0: cdns-usb@4104000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4104000 0x00 0x100>;
 		dma-coherent;
@@ -918,7 +918,7 @@
 		};
 	};
 
-	usbss1: cdns_usb@4114000 {
+	usbss1: cdns-usb@4114000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4114000 0x00 0x100>;
 		dma-coherent;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 81801f519a61..03fa69c0a038 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -249,7 +249,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index d69d90c8b5e3..5dc3ba739131 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -71,7 +71,7 @@
 };
 
 &wkup_pmx0 {
-	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
 			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
-- 
2.17.1

[PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Nishanth Menon]

Building with W=2 throws up a bunch of easy to fixup errors..
node_name_chars_strict is one of them.. Knock those out.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 8 files changed, 33 insertions(+), 33 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 9c96e3f58c86..ff3e38408dbc 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -305,7 +305,7 @@
 		no-1-8-v;
 	};
 
-	scm_conf: scm_conf@100000 {
+	scm_conf: scm-conf@100000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0 0x00100000 0 0x1c000>;
 		#address-cells = <1>;
@@ -344,7 +344,7 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
+		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
 			compatible = "syscon";
 			reg = <0x0000041E0 0x14>;
 		};
@@ -445,7 +445,7 @@
 		ti,interrupt-ranges = <0 392 32>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 6dfec68ac865..435e51019287 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -6,7 +6,7 @@
  */
 
 &cbass_mcu {
-	mcu_conf: scm_conf@40f00000 {
+	mcu_conf: scm-conf@40f00000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0x0 0x40f00000 0x0 0x20000>;
 		#address-cells = <1>;
@@ -116,7 +116,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 86c9074cb070..d12dd89f3405 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -29,7 +29,7 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		secure_ddr: secure_ddr@9e800000 {
+		secure_ddr: secure-ddr@9e800000 {
 			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
 			alignment = <0x1000>;
 			no-map;
@@ -70,14 +70,14 @@
 		>;
 	};
 
-	push_button_pins_default: push_button__pins_default {
+	push_button_pins_default: push-button-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
 			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
 		>;
 	};
 
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
 			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
@@ -93,13 +93,13 @@
 		>;
 	};
 
-	wkup_pca554_default: wkup_pca554_default {
+	wkup_pca554_default: wkup-pca554-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
 			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
@@ -116,7 +116,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
 			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
 			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
@@ -180,7 +180,7 @@
 		>;
 	};
 
-	usb1_pins_default: usb1_pins_default {
+	usb1_pins_default: usb1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
 		>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
index cdc3d40c3f60..9021c738056b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
@@ -2,13 +2,13 @@
 
 #include <dt-bindings/thermal/thermal.h>
 
-mpu0_thermal: mpu0_thermal {
+mpu0_thermal: mpu0-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 0>;
 
 	trips {
-		mpu0_crit: mpu0_crit {
+		mpu0_crit: mpu0-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
 	};
 };
 
-mpu1_thermal: mpu1_thermal {
+mpu1_thermal: mpu1-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 1>;
 
 	trips {
-		mpu1_crit: mpu1_crit {
+		mpu1_crit: mpu1-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
 	};
 };
 
-mcu_thermal: mcu_thermal {
+mcu_thermal: mcu-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 2>;
 
 	trips {
-		mcu_crit: mcu_crit {
+		mcu_crit: mcu-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index c355692796a9..648267284582 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -86,13 +86,13 @@
 };
 
 &main_pmx0 {
-	sw10_button_pins_default: sw10_button_pins_default {
+	sw10_button_pins_default: sw10-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
 			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
@@ -106,14 +106,14 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main_usbss0_pins_default {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
 			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
-	main_usbss1_pins_default: main_usbss1_pins_default {
+	main_usbss1_pins_default: main-usbss1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
 		>;
@@ -153,7 +153,7 @@
 		>;
 	};
 
-	mcasp10_pins_default: mcasp10_pins_default {
+	mcasp10_pins_default: mcasp10-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
 			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
 		>;
@@ -175,7 +175,7 @@
 };
 
 &wkup_pmx0 {
-	sw11_button_pins_default: sw11_button_pins_default {
+	sw11_button_pins_default: sw11-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
 		>;
@@ -194,7 +194,7 @@
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
 			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
@@ -211,7 +211,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
 			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 1d2a7c05b6f3..ea57d07777ba 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -86,7 +86,7 @@
 		ti,interrupt-ranges = <8 392 56>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -888,7 +888,7 @@
 		no-1-8-v;
 	};
 
-	usbss0: cdns_usb@4104000 {
+	usbss0: cdns-usb@4104000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4104000 0x00 0x100>;
 		dma-coherent;
@@ -918,7 +918,7 @@
 		};
 	};
 
-	usbss1: cdns_usb@4114000 {
+	usbss1: cdns-usb@4114000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4114000 0x00 0x100>;
 		dma-coherent;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 81801f519a61..03fa69c0a038 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -249,7 +249,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index d69d90c8b5e3..5dc3ba739131 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -71,7 +71,7 @@
 };
 
 &wkup_pmx0 {
-	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
 			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Building with W=2 throws up a bunch of easy to fixup errors..
> node_name_chars_strict is one of them.. Knock those out.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
>  .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
>  .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
>  .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
>  8 files changed, 33 insertions(+), 33 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 9c96e3f58c86..ff3e38408dbc 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -305,7 +305,7 @@
>  		no-1-8-v;
>  	};
>  
> -	scm_conf: scm_conf@100000 {
> +	scm_conf: scm-conf@100000 {
>  		compatible = "syscon", "simple-mfd";
>  		reg = <0 0x00100000 0 0x1c000>;
>  		#address-cells = <1>;
> @@ -344,7 +344,7 @@
>  					<0x4090 0x3>; /* SERDES1 lane select */
>  		};
>  
> -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> +		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
>  			compatible = "syscon";
>  			reg = <0x0000041E0 0x14>;

We should %s/41E0/41e0/, but that change is not directly associated with the
patch subject line. Perhaps, an additional patch? Remember seeing similar
warning on some downstream crypto nodes, but strangely I am not seeing on these
upstream nodes.

Otherwise,
Reviewed-by: Suman Anna <s-anna@ti.com>

regards
Suman

>  		};
> @@ -445,7 +445,7 @@
>  		ti,interrupt-ranges = <0 392 32>;
>  	};
>  
> -	main_navss {
> +	main-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> index 6dfec68ac865..435e51019287 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> @@ -6,7 +6,7 @@
>   */
>  
>  &cbass_mcu {
> -	mcu_conf: scm_conf@40f00000 {
> +	mcu_conf: scm-conf@40f00000 {
>  		compatible = "syscon", "simple-mfd";
>  		reg = <0x0 0x40f00000 0x0 0x20000>;
>  		#address-cells = <1>;
> @@ -116,7 +116,7 @@
>  		};
>  	};
>  
> -	mcu_navss {
> +	mcu-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index 86c9074cb070..d12dd89f3405 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -29,7 +29,7 @@
>  		#address-cells = <2>;
>  		#size-cells = <2>;
>  		ranges;
> -		secure_ddr: secure_ddr@9e800000 {
> +		secure_ddr: secure-ddr@9e800000 {
>  			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
>  			alignment = <0x1000>;
>  			no-map;
> @@ -70,14 +70,14 @@
>  		>;
>  	};
>  
> -	push_button_pins_default: push_button__pins_default {
> +	push_button_pins_default: push-button-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
>  			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
>  		>;
>  	};
>  
> -	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
> +	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
>  			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
> @@ -93,13 +93,13 @@
>  		>;
>  	};
>  
> -	wkup_pca554_default: wkup_pca554_default {
> +	wkup_pca554_default: wkup-pca554-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
>  		>;
>  	};
>  
> -	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
>  			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
> @@ -116,7 +116,7 @@
>  		>;
>  	};
>  
> -	mcu_mdio_pins_default: mcu_mdio1_pins_default {
> +	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>  			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
> @@ -167,7 +167,7 @@
>  		>;
>  	};
>  
> -	main_mmc1_pins_default: main_mmc1_pins_default {
> +	main_mmc1_pins_default: main-mmc1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
>  			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
> @@ -180,7 +180,7 @@
>  		>;
>  	};
>  
> -	usb1_pins_default: usb1_pins_default {
> +	usb1_pins_default: usb1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
>  		>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> index cdc3d40c3f60..9021c738056b 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> @@ -2,13 +2,13 @@
>  
>  #include <dt-bindings/thermal/thermal.h>
>  
> -mpu0_thermal: mpu0_thermal {
> +mpu0_thermal: mpu0-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 0>;
>  
>  	trips {
> -		mpu0_crit: mpu0_crit {
> +		mpu0_crit: mpu0-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> @@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
>  	};
>  };
>  
> -mpu1_thermal: mpu1_thermal {
> +mpu1_thermal: mpu1-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 1>;
>  
>  	trips {
> -		mpu1_crit: mpu1_crit {
> +		mpu1_crit: mpu1-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> @@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
>  	};
>  };
>  
> -mcu_thermal: mcu_thermal {
> +mcu_thermal: mcu-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 2>;
>  
>  	trips {
> -		mcu_crit: mcu_crit {
> +		mcu_crit: mcu-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> index c355692796a9..648267284582 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> @@ -86,13 +86,13 @@
>  };
>  
>  &main_pmx0 {
> -	sw10_button_pins_default: sw10_button_pins_default {
> +	sw10_button_pins_default: sw10-button-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
>  		>;
>  	};
>  
> -	main_mmc1_pins_default: main_mmc1_pins_default {
> +	main_mmc1_pins_default: main-mmc1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
>  			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> @@ -106,14 +106,14 @@
>  		>;
>  	};
>  
> -	main_usbss0_pins_default: main_usbss0_pins_default {
> +	main_usbss0_pins_default: main-usbss0-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
>  			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>  		>;
>  	};
>  
> -	main_usbss1_pins_default: main_usbss1_pins_default {
> +	main_usbss1_pins_default: main-usbss1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
>  		>;
> @@ -153,7 +153,7 @@
>  		>;
>  	};
>  
> -	mcasp10_pins_default: mcasp10_pins_default {
> +	mcasp10_pins_default: mcasp10-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
>  			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
> @@ -167,7 +167,7 @@
>  		>;
>  	};
>  
> -	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
> +	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
>  		>;
> @@ -175,7 +175,7 @@
>  };
>  
>  &wkup_pmx0 {
> -	sw11_button_pins_default: sw11_button_pins_default {
> +	sw11_button_pins_default: sw11-button-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
>  		>;
> @@ -194,7 +194,7 @@
>  		>;
>  	};
>  
> -	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>  			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> @@ -211,7 +211,7 @@
>  		>;
>  	};
>  
> -	mcu_mdio_pins_default: mcu_mdio1_pins_default {
> +	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
>  			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 1d2a7c05b6f3..ea57d07777ba 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -86,7 +86,7 @@
>  		ti,interrupt-ranges = <8 392 56>;
>  	};
>  
> -	main_navss {
> +	main-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> @@ -888,7 +888,7 @@
>  		no-1-8-v;
>  	};
>  
> -	usbss0: cdns_usb@4104000 {
> +	usbss0: cdns-usb@4104000 {
>  		compatible = "ti,j721e-usb";
>  		reg = <0x00 0x4104000 0x00 0x100>;
>  		dma-coherent;
> @@ -918,7 +918,7 @@
>  		};
>  	};
>  
> -	usbss1: cdns_usb@4114000 {
> +	usbss1: cdns-usb@4114000 {
>  		compatible = "ti,j721e-usb";
>  		reg = <0x00 0x4114000 0x00 0x100>;
>  		dma-coherent;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 81801f519a61..03fa69c0a038 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -249,7 +249,7 @@
>  		};
>  	};
>  
> -	mcu_navss {
> +	mcu-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> index d69d90c8b5e3..5dc3ba739131 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> @@ -71,7 +71,7 @@
>  };
>  
>  &wkup_pmx0 {
> -	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
> +	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
>  			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> 

Re: [PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Suman Anna]

On 9/1/20 5:30 PM, Nishanth Menon wrote:
> Building with W=2 throws up a bunch of easy to fixup errors..
> node_name_chars_strict is one of them.. Knock those out.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
>  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
>  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
>  .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
>  .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
>  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
>  .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
>  arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
>  8 files changed, 33 insertions(+), 33 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 9c96e3f58c86..ff3e38408dbc 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -305,7 +305,7 @@
>  		no-1-8-v;
>  	};
>  
> -	scm_conf: scm_conf@100000 {
> +	scm_conf: scm-conf@100000 {
>  		compatible = "syscon", "simple-mfd";
>  		reg = <0 0x00100000 0 0x1c000>;
>  		#address-cells = <1>;
> @@ -344,7 +344,7 @@
>  					<0x4090 0x3>; /* SERDES1 lane select */
>  		};
>  
> -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> +		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
>  			compatible = "syscon";
>  			reg = <0x0000041E0 0x14>;

We should %s/41E0/41e0/, but that change is not directly associated with the
patch subject line. Perhaps, an additional patch? Remember seeing similar
warning on some downstream crypto nodes, but strangely I am not seeing on these
upstream nodes.

Otherwise,
Reviewed-by: Suman Anna <s-anna@ti.com>

regards
Suman

>  		};
> @@ -445,7 +445,7 @@
>  		ti,interrupt-ranges = <0 392 32>;
>  	};
>  
> -	main_navss {
> +	main-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> index 6dfec68ac865..435e51019287 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
> @@ -6,7 +6,7 @@
>   */
>  
>  &cbass_mcu {
> -	mcu_conf: scm_conf@40f00000 {
> +	mcu_conf: scm-conf@40f00000 {
>  		compatible = "syscon", "simple-mfd";
>  		reg = <0x0 0x40f00000 0x0 0x20000>;
>  		#address-cells = <1>;
> @@ -116,7 +116,7 @@
>  		};
>  	};
>  
> -	mcu_navss {
> +	mcu-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> index 86c9074cb070..d12dd89f3405 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
> @@ -29,7 +29,7 @@
>  		#address-cells = <2>;
>  		#size-cells = <2>;
>  		ranges;
> -		secure_ddr: secure_ddr@9e800000 {
> +		secure_ddr: secure-ddr@9e800000 {
>  			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
>  			alignment = <0x1000>;
>  			no-map;
> @@ -70,14 +70,14 @@
>  		>;
>  	};
>  
> -	push_button_pins_default: push_button__pins_default {
> +	push_button_pins_default: push-button-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
>  			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
>  		>;
>  	};
>  
> -	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
> +	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
>  			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
> @@ -93,13 +93,13 @@
>  		>;
>  	};
>  
> -	wkup_pca554_default: wkup_pca554_default {
> +	wkup_pca554_default: wkup-pca554-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
>  		>;
>  	};
>  
> -	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
>  			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
> @@ -116,7 +116,7 @@
>  		>;
>  	};
>  
> -	mcu_mdio_pins_default: mcu_mdio1_pins_default {
> +	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>  			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
> @@ -167,7 +167,7 @@
>  		>;
>  	};
>  
> -	main_mmc1_pins_default: main_mmc1_pins_default {
> +	main_mmc1_pins_default: main-mmc1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
>  			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
> @@ -180,7 +180,7 @@
>  		>;
>  	};
>  
> -	usb1_pins_default: usb1_pins_default {
> +	usb1_pins_default: usb1-pins-default {
>  		pinctrl-single,pins = <
>  			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
>  		>;
> diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> index cdc3d40c3f60..9021c738056b 100644
> --- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
> @@ -2,13 +2,13 @@
>  
>  #include <dt-bindings/thermal/thermal.h>
>  
> -mpu0_thermal: mpu0_thermal {
> +mpu0_thermal: mpu0-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 0>;
>  
>  	trips {
> -		mpu0_crit: mpu0_crit {
> +		mpu0_crit: mpu0-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> @@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
>  	};
>  };
>  
> -mpu1_thermal: mpu1_thermal {
> +mpu1_thermal: mpu1-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 1>;
>  
>  	trips {
> -		mpu1_crit: mpu1_crit {
> +		mpu1_crit: mpu1-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> @@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
>  	};
>  };
>  
> -mcu_thermal: mcu_thermal {
> +mcu_thermal: mcu-thermal {
>  	polling-delay-passive = <250>; /* milliseconds */
>  	polling-delay = <500>; /* milliseconds */
>  	thermal-sensors = <&wkup_vtm0 2>;
>  
>  	trips {
> -		mcu_crit: mcu_crit {
> +		mcu_crit: mcu-crit {
>  			temperature = <125000>; /* milliCelsius */
>  			hysteresis = <2000>; /* milliCelsius */
>  			type = "critical";
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> index c355692796a9..648267284582 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
> @@ -86,13 +86,13 @@
>  };
>  
>  &main_pmx0 {
> -	sw10_button_pins_default: sw10_button_pins_default {
> +	sw10_button_pins_default: sw10-button-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
>  		>;
>  	};
>  
> -	main_mmc1_pins_default: main_mmc1_pins_default {
> +	main_mmc1_pins_default: main-mmc1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
>  			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
> @@ -106,14 +106,14 @@
>  		>;
>  	};
>  
> -	main_usbss0_pins_default: main_usbss0_pins_default {
> +	main_usbss0_pins_default: main-usbss0-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
>  			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
>  		>;
>  	};
>  
> -	main_usbss1_pins_default: main_usbss1_pins_default {
> +	main_usbss1_pins_default: main-usbss1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
>  		>;
> @@ -153,7 +153,7 @@
>  		>;
>  	};
>  
> -	mcasp10_pins_default: mcasp10_pins_default {
> +	mcasp10_pins_default: mcasp10-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
>  			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
> @@ -167,7 +167,7 @@
>  		>;
>  	};
>  
> -	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
> +	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
>  		>;
> @@ -175,7 +175,7 @@
>  };
>  
>  &wkup_pmx0 {
> -	sw11_button_pins_default: sw11_button_pins_default {
> +	sw11_button_pins_default: sw11-button-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
>  		>;
> @@ -194,7 +194,7 @@
>  		>;
>  	};
>  
> -	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
> +	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>  			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
> @@ -211,7 +211,7 @@
>  		>;
>  	};
>  
> -	mcu_mdio_pins_default: mcu_mdio1_pins_default {
> +	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
>  			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> index 1d2a7c05b6f3..ea57d07777ba 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
> @@ -86,7 +86,7 @@
>  		ti,interrupt-ranges = <8 392 56>;
>  	};
>  
> -	main_navss {
> +	main-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> @@ -888,7 +888,7 @@
>  		no-1-8-v;
>  	};
>  
> -	usbss0: cdns_usb@4104000 {
> +	usbss0: cdns-usb@4104000 {
>  		compatible = "ti,j721e-usb";
>  		reg = <0x00 0x4104000 0x00 0x100>;
>  		dma-coherent;
> @@ -918,7 +918,7 @@
>  		};
>  	};
>  
> -	usbss1: cdns_usb@4114000 {
> +	usbss1: cdns-usb@4114000 {
>  		compatible = "ti,j721e-usb";
>  		reg = <0x00 0x4114000 0x00 0x100>;
>  		dma-coherent;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> index 81801f519a61..03fa69c0a038 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
> @@ -249,7 +249,7 @@
>  		};
>  	};
>  
> -	mcu_navss {
> +	mcu-navss {
>  		compatible = "simple-mfd";
>  		#address-cells = <2>;
>  		#size-cells = <2>;
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> index d69d90c8b5e3..5dc3ba739131 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
> @@ -71,7 +71,7 @@
>  };
>  
>  &wkup_pmx0 {
> -	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
> +	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
>  		pinctrl-single,pins = <
>  			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
>  			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Nishanth Menon]

On 11:54-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Building with W=2 throws up a bunch of easy to fixup errors..
> > node_name_chars_strict is one of them.. Knock those out.
> > 
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
> >  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
> >  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
> >  .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
> >  .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
> >  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
> >  .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
> >  arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
> >  8 files changed, 33 insertions(+), 33 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > index 9c96e3f58c86..ff3e38408dbc 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > @@ -305,7 +305,7 @@
> >  		no-1-8-v;
> >  	};
> >  
> > -	scm_conf: scm_conf@100000 {
> > +	scm_conf: scm-conf@100000 {
> >  		compatible = "syscon", "simple-mfd";
> >  		reg = <0 0x00100000 0 0x1c000>;
> >  		#address-cells = <1>;
> > @@ -344,7 +344,7 @@
> >  					<0x4090 0x3>; /* SERDES1 lane select */
> >  		};
> >  
> > -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> > +		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
> >  			compatible = "syscon";
> >  			reg = <0x0000041E0 0x14>;
> 
> We should %s/41E0/41e0/, but that change is not directly associated with the
> patch subject line. Perhaps, an additional patch? Remember seeing similar
> warning on some downstream crypto nodes, but strangely I am not seeing on these
> upstream nodes.

yeah - probably a separate patch, but thanks, i can fix it as well(will
check if there are similar ones around as well).

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH 7/7] arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

[Nishanth Menon]

On 11:54-20200902, Suman Anna wrote:
> On 9/1/20 5:30 PM, Nishanth Menon wrote:
> > Building with W=2 throws up a bunch of easy to fixup errors..
> > node_name_chars_strict is one of them.. Knock those out.
> > 
> > Signed-off-by: Nishanth Menon <nm@ti.com>
> > ---
> >  arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
> >  arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
> >  arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
> >  .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
> >  .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
> >  arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
> >  .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
> >  arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
> >  8 files changed, 33 insertions(+), 33 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > index 9c96e3f58c86..ff3e38408dbc 100644
> > --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> > @@ -305,7 +305,7 @@
> >  		no-1-8-v;
> >  	};
> >  
> > -	scm_conf: scm_conf@100000 {
> > +	scm_conf: scm-conf@100000 {
> >  		compatible = "syscon", "simple-mfd";
> >  		reg = <0 0x00100000 0 0x1c000>;
> >  		#address-cells = <1>;
> > @@ -344,7 +344,7 @@
> >  					<0x4090 0x3>; /* SERDES1 lane select */
> >  		};
> >  
> > -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> > +		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41E0 {
> >  			compatible = "syscon";
> >  			reg = <0x0000041E0 0x14>;
> 
> We should %s/41E0/41e0/, but that change is not directly associated with the
> patch subject line. Perhaps, an additional patch? Remember seeing similar
> warning on some downstream crypto nodes, but strangely I am not seeing on these
> upstream nodes.

yeah - probably a separate patch, but thanks, i can fix it as well(will
check if there are similar ones around as well).

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/7] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings

[Lokesh Vutla]

On 02/09/20 4:00 am, Nishanth Menon wrote:
> Hi,
> 
> This is one part of cleanups meant for make W=2 dtbs for 5.10 on TI
> dtbs. Hopefully we dont see node_name_chars_strict warnings anymore.
> 
> As part of this cleanup, I ran a cross check of nodes that are
> part of K3 as of right now, Vs what is "generic" definition as per 0.3
> dt specification:
> https://pastebin.ubuntu.com/p/kp3g4ktBYp/
> 
> I dont think the remaining have a good reference, at least in my
> subjective view.
> 
> In possibly some cases, bootloaders may need to sync before doing DT
> fixup etc.
> 
> Nishanth Menon (7):
>   arm64: dts: ti: k3-am65*: Use generic gpio for node names
>   arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name
>   arm64: dts: ti: k3-*: Use generic pinctrl for node names
>   arm64: dts: ti: k3-am65-base-board Use generic camera for node name
>     instead of ov5640
>   arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
>     node name
>   arm64: dts: ti: k3-*: Use generic adc for node names
>   arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

Series looks good to me,

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh

Re: [PATCH 0/7] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings

[Lokesh Vutla]

On 02/09/20 4:00 am, Nishanth Menon wrote:
> Hi,
> 
> This is one part of cleanups meant for make W=2 dtbs for 5.10 on TI
> dtbs. Hopefully we dont see node_name_chars_strict warnings anymore.
> 
> As part of this cleanup, I ran a cross check of nodes that are
> part of K3 as of right now, Vs what is "generic" definition as per 0.3
> dt specification:
> https://pastebin.ubuntu.com/p/kp3g4ktBYp/
> 
> I dont think the remaining have a good reference, at least in my
> subjective view.
> 
> In possibly some cases, bootloaders may need to sync before doing DT
> fixup etc.
> 
> Nishanth Menon (7):
>   arm64: dts: ti: k3-am65*: Use generic gpio for node names
>   arm64: dts: ti: k3-am65*: Use generic clock for serdes clock name
>   arm64: dts: ti: k3-*: Use generic pinctrl for node names
>   arm64: dts: ti: k3-am65-base-board Use generic camera for node name
>     instead of ov5640
>   arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
>     node name
>   arm64: dts: ti: k3-*: Use generic adc for node names
>   arm64: dts: ti: k3-*: Fix up node_name_chars_strict errors

Series looks good to me,

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 0/8] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings + hex usage

[Nishanth Menon]

Hi,

This is a respin of v2 of the series posted as [1].

As part of this cleanup, I ran a cross check of nodes that are
part of K3 as of right now, Vs what is "generic" definition as per 0.3
dt specification [2].

Changes in v2:
- Based off 20200903
- Picked up Acks and reviewed-by from previous versions (please comment
  if you disagree).
- Dropped tsadc rename [3] based on review
- Added 2 patches to fixup hexadecimal usage caught as part of review
- few additional fixups.


Nishanth Menon (8):
  arm64: dts: ti: k3-j721e: Use lower case hexadecimal
  arm64: dts: ti: k3-am65-main: Use lower case hexadecimal
  arm64: dts: ti: k3-am65*: Use generic gpio for node names
  arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names
  arm64: dts: ti: k3-*: Use generic pinctrl for node names
  arm64: dts: ti: k3-am65-base-board Use generic camera for node name
    instead of ov5640
  arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
    node name
  arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi      | 22 +++++++++----------
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi       |  4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi    |  6 ++---
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 18 +++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi   | 12 +++++-----
 .../dts/ti/k3-j721e-common-proc-board.dts     | 18 +++++++--------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     |  8 +++----
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |  4 ++--
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi   |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e.dtsi          |  2 +-
 10 files changed, 48 insertions(+), 48 deletions(-)

[1] v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-1-nm@ti.com/
[2] https://pastebin.ubuntu.com/p/Z5zGQydH3G/
[3] https://lore.kernel.org/linux-arm-kernel/9fb2f8f4-5eeb-6190-9cbf-b28084c58a8f@ti.com/

-- 
2.17.1

[PATCH V2 0/8] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings + hex usage

[Nishanth Menon]

Hi,

This is a respin of v2 of the series posted as [1].

As part of this cleanup, I ran a cross check of nodes that are
part of K3 as of right now, Vs what is "generic" definition as per 0.3
dt specification [2].

Changes in v2:
- Based off 20200903
- Picked up Acks and reviewed-by from previous versions (please comment
  if you disagree).
- Dropped tsadc rename [3] based on review
- Added 2 patches to fixup hexadecimal usage caught as part of review
- few additional fixups.


Nishanth Menon (8):
  arm64: dts: ti: k3-j721e: Use lower case hexadecimal
  arm64: dts: ti: k3-am65-main: Use lower case hexadecimal
  arm64: dts: ti: k3-am65*: Use generic gpio for node names
  arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names
  arm64: dts: ti: k3-*: Use generic pinctrl for node names
  arm64: dts: ti: k3-am65-base-board Use generic camera for node name
    instead of ov5640
  arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for
    node name
  arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi      | 22 +++++++++----------
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi       |  4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi    |  6 ++---
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 18 +++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi   | 12 +++++-----
 .../dts/ti/k3-j721e-common-proc-board.dts     | 18 +++++++--------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi     |  8 +++----
 .../boot/dts/ti/k3-j721e-mcu-wakeup.dtsi      |  4 ++--
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi   |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e.dtsi          |  2 +-
 10 files changed, 48 insertions(+), 48 deletions(-)

[1] v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-1-nm@ti.com/
[2] https://pastebin.ubuntu.com/p/Z5zGQydH3G/
[3] https://lore.kernel.org/linux-arm-kernel/9fb2f8f4-5eeb-6190-9cbf-b28084c58a8f@ti.com/

-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 0/8] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings + hex usage

[Nishanth Menon]

On 08:00-20200903, Nishanth Menon wrote:
> Hi,
> 
> This is a respin of v2 of the series posted as [1].
> 
> As part of this cleanup, I ran a cross check of nodes that are
> part of K3 as of right now, Vs what is "generic" definition as per 0.3
> dt specification [2].
> 
> Changes in v2:
> - Based off 20200903
> - Picked up Acks and reviewed-by from previous versions (please comment
>   if you disagree).
> - Dropped tsadc rename [3] based on review
> - Added 2 patches to fixup hexadecimal usage caught as part of review
> - few additional fixups.
I have applied the following to branch ti-k3-next on [1].

[1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal
      commit: 1aedefe13ba263d0d7d1cfbb38aadebbd5bab34e
[2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal
      commit: 05e393c596c4495d79f0cbeacb0f0a0e0b6f89d5
[3/8] arm64: dts: ti: k3-am65*: Use generic gpio for node names
      commit: 91e5f404e42bc189bb0e447d30041de737ad24bf
[4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names
      commit: 86e67b591e6d993d98567143451883a5618c196e
[5/8] arm64: dts: ti: k3-*: Use generic pinctrl for node names
      commit: dcccf77067e4274953e8944d9730bb7ae2964c28
[6/8] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640
      commit: 4c19fb9ce266561ab122880a02e873ee8c3668e4
[7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name
      commit: 9a8ecd414322ceb377cecb4795e3f3d7d7020952
[8/8] arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings
      commit: e5c956c4f36cdd59e775f2285af9a1683374c5a5

[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH V2 0/8] arm64: dts: ti: k3-*: Squash up node_name_chars_strict warnings + hex usage

[Nishanth Menon]

On 08:00-20200903, Nishanth Menon wrote:
> Hi,
> 
> This is a respin of v2 of the series posted as [1].
> 
> As part of this cleanup, I ran a cross check of nodes that are
> part of K3 as of right now, Vs what is "generic" definition as per 0.3
> dt specification [2].
> 
> Changes in v2:
> - Based off 20200903
> - Picked up Acks and reviewed-by from previous versions (please comment
>   if you disagree).
> - Dropped tsadc rename [3] based on review
> - Added 2 patches to fixup hexadecimal usage caught as part of review
> - few additional fixups.
I have applied the following to branch ti-k3-next on [1].

[1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal
      commit: 1aedefe13ba263d0d7d1cfbb38aadebbd5bab34e
[2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal
      commit: 05e393c596c4495d79f0cbeacb0f0a0e0b6f89d5
[3/8] arm64: dts: ti: k3-am65*: Use generic gpio for node names
      commit: 91e5f404e42bc189bb0e447d30041de737ad24bf
[4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names
      commit: 86e67b591e6d993d98567143451883a5618c196e
[5/8] arm64: dts: ti: k3-*: Use generic pinctrl for node names
      commit: dcccf77067e4274953e8944d9730bb7ae2964c28
[6/8] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640
      commit: 4c19fb9ce266561ab122880a02e873ee8c3668e4
[7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name
      commit: 9a8ecd414322ceb377cecb4795e3f3d7d7020952
[8/8] arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings
      commit: e5c956c4f36cdd59e775f2285af9a1683374c5a5

[1] git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux.git
-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Nishanth Menon]

Device tree convention uses lower case a-f for hexadecimals. Fix the
same.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
Change:
v2: - new

 arch/arm64/boot/dts/ti/k3-j721e.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index f787aa73aaae..1bb8235d9ffb 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -127,7 +127,7 @@
 		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
 			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
 			 <0x00 0x00900000 0x00 0x00900000 0x00 0x00012000>, /* serdes */
-			 <0x00 0x00A40000 0x00 0x00A40000 0x00 0x00000800>, /* timesync router */
+			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
 			 <0x00 0x06000000 0x00 0x06000000 0x00 0x00400000>, /* USBSS0 */
 			 <0x00 0x06400000 0x00 0x06400000 0x00 0x00400000>, /* USBSS1 */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0af02400>, /* Most peripherals */
-- 
2.17.1

[PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Nishanth Menon]

Device tree convention uses lower case a-f for hexadecimals. Fix the
same.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
Change:
v2: - new

 arch/arm64/boot/dts/ti/k3-j721e.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index f787aa73aaae..1bb8235d9ffb 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -127,7 +127,7 @@
 		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
 			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
 			 <0x00 0x00900000 0x00 0x00900000 0x00 0x00012000>, /* serdes */
-			 <0x00 0x00A40000 0x00 0x00A40000 0x00 0x00000800>, /* timesync router */
+			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
 			 <0x00 0x06000000 0x00 0x06000000 0x00 0x00400000>, /* USBSS0 */
 			 <0x00 0x06400000 0x00 0x06400000 0x00 0x00400000>, /* USBSS1 */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0af02400>, /* Most peripherals */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Suman Anna]

<<< No Message Collected >>>

Re: [PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Suman Anna]

On 9/3/20 8:00 AM, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
> Change:
> v2: - new
> 
>  arch/arm64/boot/dts/ti/k3-j721e.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> index f787aa73aaae..1bb8235d9ffb 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> @@ -127,7 +127,7 @@
>  		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
>  			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
>  			 <0x00 0x00900000 0x00 0x00900000 0x00 0x00012000>, /* serdes */
> -			 <0x00 0x00A40000 0x00 0x00A40000 0x00 0x00000800>, /* timesync router */
> +			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
>  			 <0x00 0x06000000 0x00 0x06000000 0x00 0x00400000>, /* USBSS0 */
>  			 <0x00 0x06400000 0x00 0x06400000 0x00 0x00400000>, /* USBSS1 */
>  			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0af02400>, /* Most peripherals */
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Suman Anna]

On 9/3/20 8:00 AM, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
> Change:
> v2: - new
> 
>  arch/arm64/boot/dts/ti/k3-j721e.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> index f787aa73aaae..1bb8235d9ffb 100644
> --- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
> @@ -127,7 +127,7 @@
>  		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
>  			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
>  			 <0x00 0x00900000 0x00 0x00900000 0x00 0x00012000>, /* serdes */
> -			 <0x00 0x00A40000 0x00 0x00A40000 0x00 0x00000800>, /* timesync router */
> +			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
>  			 <0x00 0x06000000 0x00 0x06000000 0x00 0x00400000>, /* USBSS0 */
>  			 <0x00 0x06400000 0x00 0x06400000 0x00 0x00400000>, /* USBSS1 */
>  			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0af02400>, /* Most peripherals */
> 

Re: [PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Lokesh Vutla]

On 03/09/20 6:30 pm, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh

Re: [PATCH V2 1/8] arm64: dts: ti: k3-j721e: Use lower case hexadecimal

[Lokesh Vutla]

On 03/09/20 6:30 pm, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Nishanth Menon]

Device tree convention uses lower case a-f for hexadecimals. Fix the
same.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
Change:
v2: - new

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 76e0edc4ad5c..d53d1ead4bb6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -344,9 +344,9 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
+		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
 			compatible = "syscon";
-			reg = <0x0000041E0 0x14>;
+			reg = <0x0000041e0 0x14>;
 		};
 
 		ehrpwm_tbclk: syscon@4140 {
-- 
2.17.1

[PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Nishanth Menon]

Device tree convention uses lower case a-f for hexadecimals. Fix the
same.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
Change:
v2: - new

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 76e0edc4ad5c..d53d1ead4bb6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -344,9 +344,9 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
+		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
 			compatible = "syscon";
-			reg = <0x0000041E0 0x14>;
+			reg = <0x0000041e0 0x14>;
 		};
 
 		ehrpwm_tbclk: syscon@4140 {
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Suman Anna]

On 9/3/20 8:00 AM, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
> Change:
> v2: - new
> 
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 76e0edc4ad5c..d53d1ead4bb6 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -344,9 +344,9 @@
>  					<0x4090 0x3>; /* SERDES1 lane select */
>  		};
>  
> -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> +		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
>  			compatible = "syscon";
> -			reg = <0x0000041E0 0x14>;
> +			reg = <0x0000041e0 0x14>;
>  		};
>  
>  		ehrpwm_tbclk: syscon@4140 {
> 

Re: [PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Suman Anna]

On 9/3/20 8:00 AM, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Acked-by: Suman Anna <s-anna@ti.com>

> ---
> Change:
> v2: - new
> 
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index 76e0edc4ad5c..d53d1ead4bb6 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -344,9 +344,9 @@
>  					<0x4090 0x3>; /* SERDES1 lane select */
>  		};
>  
> -		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41E0 {
> +		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
>  			compatible = "syscon";
> -			reg = <0x0000041E0 0x14>;
> +			reg = <0x0000041e0 0x14>;
>  		};
>  
>  		ehrpwm_tbclk: syscon@4140 {
> 


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Lokesh Vutla]

On 03/09/20 6:30 pm, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh

Re: [PATCH V2 2/8] arm64: dts: ti: k3-am65-main: Use lower case hexadecimal

[Lokesh Vutla]

On 03/09/20 6:30 pm, Nishanth Menon wrote:
> Device tree convention uses lower case a-f for hexadecimals. Fix the
> same.
> 
> Signed-off-by: Nishanth Menon <nm@ti.com>

Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>

Thanks and regards,
Lokesh


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 3/8] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Nishanth Menon]

Use gpio@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Change:
v2: No functional change, picked reviews and acks
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-2-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index d53d1ead4bb6..a2fc508e59a6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -661,7 +661,7 @@
 		};
 	};
 
-	main_gpio0:  main_gpio0@600000 {
+	main_gpio0: gpio@600000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x600000 0x0 0x100>;
 		gpio-controller;
@@ -676,7 +676,7 @@
 		clock-names = "gpio";
 	};
 
-	main_gpio1:  main_gpio1@601000 {
+	main_gpio1: gpio@601000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x601000 0x0 0x100>;
 		gpio-controller;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index a1ffe88d9664..0765700a8ba8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -80,7 +80,7 @@
 		ti,interrupt-ranges = <0 712 16>;
 	};
 
-	wkup_gpio0: wkup_gpio0@42110000 {
+	wkup_gpio0: gpio@42110000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x42110000 0x100>;
 		gpio-controller;
-- 
2.17.1

[PATCH V2 3/8] arm64: dts: ti: k3-am65*: Use generic gpio for node names

[Nishanth Menon]

Use gpio@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Change:
v2: No functional change, picked reviews and acks
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-2-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi   | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index d53d1ead4bb6..a2fc508e59a6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -661,7 +661,7 @@
 		};
 	};
 
-	main_gpio0:  main_gpio0@600000 {
+	main_gpio0: gpio@600000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x600000 0x0 0x100>;
 		gpio-controller;
@@ -676,7 +676,7 @@
 		clock-names = "gpio";
 	};
 
-	main_gpio1:  main_gpio1@601000 {
+	main_gpio1: gpio@601000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x0 0x601000 0x0 0x100>;
 		gpio-controller;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index a1ffe88d9664..0765700a8ba8 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -80,7 +80,7 @@
 		ti,interrupt-ranges = <0 712 16>;
 	};
 
-	wkup_gpio0: wkup_gpio0@42110000 {
+	wkup_gpio0: gpio@42110000 {
 		compatible = "ti,am654-gpio", "ti,keystone-gpio";
 		reg = <0x42110000 0x100>;
 		gpio-controller;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names

[Nishanth Menon]

serdes and ehrpwm_tbclk nodes should be using clock@ naming for nodes
following standard conventions of device tree (section 2.2.2 Generic
Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Change:
v2:  added ehrpwm_tbclk based on review comments.
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-3-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index a2fc508e59a6..63a1299cb0b2 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -327,12 +327,12 @@
 			reg = <0x00000210 0x4>;
 		};
 
-		serdes0_clk: serdes_clk@4080 {
+		serdes0_clk: clock@4080 {
 			compatible = "syscon";
 			reg = <0x00004080 0x4>;
 		};
 
-		serdes1_clk: serdes_clk@4090 {
+		serdes1_clk: clock@4090 {
 			compatible = "syscon";
 			reg = <0x00004090 0x4>;
 		};
@@ -349,7 +349,7 @@
 			reg = <0x0000041e0 0x14>;
 		};
 
-		ehrpwm_tbclk: syscon@4140 {
+		ehrpwm_tbclk: clock@4140 {
 			compatible = "ti,am654-ehrpwm-tbclk", "syscon";
 			reg = <0x4140 0x18>;
 			#clock-cells = <1>;
-- 
2.17.1

[PATCH V2 4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names

[Nishanth Menon]

serdes and ehrpwm_tbclk nodes should be using clock@ naming for nodes
following standard conventions of device tree (section 2.2.2 Generic
Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Change:
v2:  added ehrpwm_tbclk based on review comments.
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-3-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index a2fc508e59a6..63a1299cb0b2 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -327,12 +327,12 @@
 			reg = <0x00000210 0x4>;
 		};
 
-		serdes0_clk: serdes_clk@4080 {
+		serdes0_clk: clock@4080 {
 			compatible = "syscon";
 			reg = <0x00004080 0x4>;
 		};
 
-		serdes1_clk: serdes_clk@4090 {
+		serdes1_clk: clock@4090 {
 			compatible = "syscon";
 			reg = <0x00004090 0x4>;
 		};
@@ -349,7 +349,7 @@
 			reg = <0x0000041e0 0x14>;
 		};
 
-		ehrpwm_tbclk: syscon@4140 {
+		ehrpwm_tbclk: clock@4140 {
 			compatible = "ti,am654-ehrpwm-tbclk", "syscon";
 			reg = <0x4140 0x18>;
 			#clock-cells = <1>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names

[Vignesh Raghavendra]

On 9/3/20 6:30 PM, Nishanth Menon wrote:
> serdes and ehrpwm_tbclk nodes should be using clock@ naming for nodes
> following standard conventions of device tree (section 2.2.2 Generic
> Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
> Acked-by: Suman Anna <s-anna@ti.com>
> ---
> Change:
> v2:  added ehrpwm_tbclk based on review comments.
> v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-3-nm@ti.com/
> 
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index a2fc508e59a6..63a1299cb0b2 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -327,12 +327,12 @@
>  			reg = <0x00000210 0x4>;
>  		};
>  
> -		serdes0_clk: serdes_clk@4080 {
> +		serdes0_clk: clock@4080 {
>  			compatible = "syscon";
>  			reg = <0x00004080 0x4>;
>  		};
>  
> -		serdes1_clk: serdes_clk@4090 {
> +		serdes1_clk: clock@4090 {
>  			compatible = "syscon";
>  			reg = <0x00004090 0x4>;
>  		};
> @@ -349,7 +349,7 @@
>  			reg = <0x0000041e0 0x14>;
>  		};
>  
> -		ehrpwm_tbclk: syscon@4140 {
> +		ehrpwm_tbclk: clock@4140 {
>  			compatible = "ti,am654-ehrpwm-tbclk", "syscon";
>  			reg = <0x4140 0x18>;
>  			#clock-cells = <1>;
> 

Acked-by: Vignesh Raghavendra <vigneshr@ti.com>

Re: [PATCH V2 4/8] arm64: dts: ti: k3-am65*: Use generic clock for syscon clock names

[Vignesh Raghavendra]

On 9/3/20 6:30 PM, Nishanth Menon wrote:
> serdes and ehrpwm_tbclk nodes should be using clock@ naming for nodes
> following standard conventions of device tree (section 2.2.2 Generic
> Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
> Acked-by: Suman Anna <s-anna@ti.com>
> ---
> Change:
> v2:  added ehrpwm_tbclk based on review comments.
> v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-3-nm@ti.com/
> 
>  arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 6 +++---
>  1 file changed, 3 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> index a2fc508e59a6..63a1299cb0b2 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
> @@ -327,12 +327,12 @@
>  			reg = <0x00000210 0x4>;
>  		};
>  
> -		serdes0_clk: serdes_clk@4080 {
> +		serdes0_clk: clock@4080 {
>  			compatible = "syscon";
>  			reg = <0x00004080 0x4>;
>  		};
>  
> -		serdes1_clk: serdes_clk@4090 {
> +		serdes1_clk: clock@4090 {
>  			compatible = "syscon";
>  			reg = <0x00004090 0x4>;
>  		};
> @@ -349,7 +349,7 @@
>  			reg = <0x0000041e0 0x14>;
>  		};
>  
> -		ehrpwm_tbclk: syscon@4140 {
> +		ehrpwm_tbclk: clock@4140 {
>  			compatible = "ti,am654-ehrpwm-tbclk", "syscon";
>  			reg = <0x4140 0x18>;
>  			#clock-cells = <1>;
> 

Acked-by: Vignesh Raghavendra <vigneshr@ti.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 5/8] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Nishanth Menon]

Use pinctrl@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-4-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 63a1299cb0b2..1dd488cb15c6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -134,7 +134,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c000 0x0 0x2e4>;
 		#pinctrl-cells = <1>;
@@ -142,7 +142,7 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
-	main_pmx1: pinmux@11c2e8 {
+	main_pmx1: pinctrl@11c2e8 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c2e8 0x0 0x24>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 0765700a8ba8..bb498be2f0a4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -39,7 +39,7 @@
 		reg = <0x43000014 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		reg = <0x4301c000 0x118>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 00a36a14efe7..1d2a7c05b6f3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -327,7 +327,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x0 0x11c000 0x0 0x2b4>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index c4a48e8d420a..9ad0266598ad 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -53,7 +53,7 @@
 		reg = <0x0 0x43000014 0x0 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x178>;
-- 
2.17.1

[PATCH V2 5/8] arm64: dts: ti: k3-*: Use generic pinctrl for node names

[Nishanth Menon]

Use pinctrl@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-4-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi        | 4 ++--
 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi      | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi       | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi | 2 +-
 4 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 63a1299cb0b2..1dd488cb15c6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -134,7 +134,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c000 0x0 0x2e4>;
 		#pinctrl-cells = <1>;
@@ -142,7 +142,7 @@
 		pinctrl-single,function-mask = <0xffffffff>;
 	};
 
-	main_pmx1: pinmux@11c2e8 {
+	main_pmx1: pinctrl@11c2e8 {
 		compatible = "pinctrl-single";
 		reg = <0x0 0x11c2e8 0x0 0x24>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 0765700a8ba8..bb498be2f0a4 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -39,7 +39,7 @@
 		reg = <0x43000014 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		reg = <0x4301c000 0x118>;
 		#pinctrl-cells = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 00a36a14efe7..1d2a7c05b6f3 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -327,7 +327,7 @@
 		};
 	};
 
-	main_pmx0: pinmux@11c000 {
+	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x0 0x11c000 0x0 0x2b4>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index c4a48e8d420a..9ad0266598ad 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -53,7 +53,7 @@
 		reg = <0x0 0x43000014 0x0 0x4>;
 	};
 
-	wkup_pmx0: pinmux@4301c000 {
+	wkup_pmx0: pinctrl@4301c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
 		reg = <0x00 0x4301c000 0x00 0x178>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 6/8] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Nishanth Menon]

Use camera@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-5-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index b8a8a0fcb8af..86c9074cb070 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -257,7 +257,7 @@
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
 
-	ov5640@3c {
+	ov5640: camera@3c {
 		compatible = "ovti,ov5640";
 		reg = <0x3c>;
 
-- 
2.17.1

[PATCH V2 6/8] arm64: dts: ti: k3-am65-base-board Use generic camera for node name instead of ov5640

[Nishanth Menon]

Use camera@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-5-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index b8a8a0fcb8af..86c9074cb070 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -257,7 +257,7 @@
 	pinctrl-0 = <&main_i2c1_pins_default>;
 	clock-frequency = <400000>;
 
-	ov5640@3c {
+	ov5640: camera@3c {
 		compatible = "ovti,ov5640";
 		reg = <0x3c>;
 
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

Use temperature-sensor@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-6-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index bb498be2f0a4..ed42f13e7663 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -95,7 +95,7 @@
 		clock-names = "gpio";
 	};
 
-	wkup_vtm0: thermal@42050000 {
+	wkup_vtm0: temperature-sensor@42050000 {
 		compatible = "ti,am654-vtm";
 		reg = <0x42050000 0x25c>;
 		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
-- 
2.17.1

[PATCH V2 7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Nishanth Menon]

Use temperature-sensor@ naming for nodes following standard conventions of device
tree (section 2.2.2 Generic Names recommendation in [1]).

[1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3

Suggested-by: Suman Anna <s-anna@ti.com>
Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (picked acks/reviews)
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-6-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index bb498be2f0a4..ed42f13e7663 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -95,7 +95,7 @@
 		clock-names = "gpio";
 	};
 
-	wkup_vtm0: thermal@42050000 {
+	wkup_vtm0: temperature-sensor@42050000 {
 		compatible = "ti,am654-vtm";
 		reg = <0x42050000 0x25c>;
 		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH V2 7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Vignesh Raghavendra]

On 9/3/20 6:30 PM, Nishanth Menon wrote:
> Use temperature-sensor@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
> Reviewed-by: Suman Anna <s-anna@ti.com>

Acked-by: Vignesh Raghavendra <vigneshr@ti.com>

> ---
> Changes:
> v2: None (picked acks/reviews)
> v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-6-nm@ti.com/
> 
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index bb498be2f0a4..ed42f13e7663 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -95,7 +95,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	wkup_vtm0: thermal@42050000 {
> +	wkup_vtm0: temperature-sensor@42050000 {
>  		compatible = "ti,am654-vtm";
>  		reg = <0x42050000 0x25c>;
>  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> 

Re: [PATCH V2 7/8] arm64: dts: ti: k3-am65-wakeup: Use generic temperature-sensor for node name

[Vignesh Raghavendra]

On 9/3/20 6:30 PM, Nishanth Menon wrote:
> Use temperature-sensor@ naming for nodes following standard conventions of device
> tree (section 2.2.2 Generic Names recommendation in [1]).
> 
> [1] https://github.com/devicetree-org/devicetree-specification/tree/v0.3
> 
> Suggested-by: Suman Anna <s-anna@ti.com>
> Suggested-by: Vignesh Raghavendra <vigneshr@ti.com>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
> Reviewed-by: Suman Anna <s-anna@ti.com>

Acked-by: Vignesh Raghavendra <vigneshr@ti.com>

> ---
> Changes:
> v2: None (picked acks/reviews)
> v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-6-nm@ti.com/
> 
>  arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi | 2 +-
>  1 file changed, 1 insertion(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> index bb498be2f0a4..ed42f13e7663 100644
> --- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
> @@ -95,7 +95,7 @@
>  		clock-names = "gpio";
>  	};
>  
> -	wkup_vtm0: thermal@42050000 {
> +	wkup_vtm0: temperature-sensor@42050000 {
>  		compatible = "ti,am654-vtm";
>  		reg = <0x42050000 0x25c>;
>  		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 8/8] arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings

[Nishanth Menon]

Building with W=2 throws up a bunch of easy to fixup warnings..
node_name_chars_strict is one of them.. Knock those out.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (rebase) (picked acks/reviews) - comment on hex usage split as
  seperate patch
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-8-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 8 files changed, 33 insertions(+), 33 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 1dd488cb15c6..533525229a8d 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -305,7 +305,7 @@
 		no-1-8-v;
 	};
 
-	scm_conf: scm_conf@100000 {
+	scm_conf: scm-conf@100000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0 0x00100000 0 0x1c000>;
 		#address-cells = <1>;
@@ -344,7 +344,7 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
+		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41e0 {
 			compatible = "syscon";
 			reg = <0x0000041e0 0x14>;
 		};
@@ -445,7 +445,7 @@
 		ti,interrupt-ranges = <0 392 32>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 51ca4b4d4c21..29aaf8dca6f6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -6,7 +6,7 @@
  */
 
 &cbass_mcu {
-	mcu_conf: scm_conf@40f00000 {
+	mcu_conf: scm-conf@40f00000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0x0 0x40f00000 0x0 0x20000>;
 		#address-cells = <1>;
@@ -116,7 +116,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 86c9074cb070..d12dd89f3405 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -29,7 +29,7 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		secure_ddr: secure_ddr@9e800000 {
+		secure_ddr: secure-ddr@9e800000 {
 			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
 			alignment = <0x1000>;
 			no-map;
@@ -70,14 +70,14 @@
 		>;
 	};
 
-	push_button_pins_default: push_button__pins_default {
+	push_button_pins_default: push-button-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
 			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
 		>;
 	};
 
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
 			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
@@ -93,13 +93,13 @@
 		>;
 	};
 
-	wkup_pca554_default: wkup_pca554_default {
+	wkup_pca554_default: wkup-pca554-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
 			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
@@ -116,7 +116,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
 			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
 			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
@@ -180,7 +180,7 @@
 		>;
 	};
 
-	usb1_pins_default: usb1_pins_default {
+	usb1_pins_default: usb1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
 		>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
index cdc3d40c3f60..9021c738056b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
@@ -2,13 +2,13 @@
 
 #include <dt-bindings/thermal/thermal.h>
 
-mpu0_thermal: mpu0_thermal {
+mpu0_thermal: mpu0-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 0>;
 
 	trips {
-		mpu0_crit: mpu0_crit {
+		mpu0_crit: mpu0-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
 	};
 };
 
-mpu1_thermal: mpu1_thermal {
+mpu1_thermal: mpu1-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 1>;
 
 	trips {
-		mpu1_crit: mpu1_crit {
+		mpu1_crit: mpu1-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
 	};
 };
 
-mcu_thermal: mcu_thermal {
+mcu_thermal: mcu-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 2>;
 
 	trips {
-		mcu_crit: mcu_crit {
+		mcu_crit: mcu-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index c355692796a9..648267284582 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -86,13 +86,13 @@
 };
 
 &main_pmx0 {
-	sw10_button_pins_default: sw10_button_pins_default {
+	sw10_button_pins_default: sw10-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
 			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
@@ -106,14 +106,14 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main_usbss0_pins_default {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
 			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
-	main_usbss1_pins_default: main_usbss1_pins_default {
+	main_usbss1_pins_default: main-usbss1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
 		>;
@@ -153,7 +153,7 @@
 		>;
 	};
 
-	mcasp10_pins_default: mcasp10_pins_default {
+	mcasp10_pins_default: mcasp10-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
 			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
 		>;
@@ -175,7 +175,7 @@
 };
 
 &wkup_pmx0 {
-	sw11_button_pins_default: sw11_button_pins_default {
+	sw11_button_pins_default: sw11-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
 		>;
@@ -194,7 +194,7 @@
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
 			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
@@ -211,7 +211,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
 			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 1d2a7c05b6f3..ea57d07777ba 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -86,7 +86,7 @@
 		ti,interrupt-ranges = <8 392 56>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -888,7 +888,7 @@
 		no-1-8-v;
 	};
 
-	usbss0: cdns_usb@4104000 {
+	usbss0: cdns-usb@4104000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4104000 0x00 0x100>;
 		dma-coherent;
@@ -918,7 +918,7 @@
 		};
 	};
 
-	usbss1: cdns_usb@4114000 {
+	usbss1: cdns-usb@4114000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4114000 0x00 0x100>;
 		dma-coherent;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 9ad0266598ad..e581cb1d87ee 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -249,7 +249,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index d69d90c8b5e3..5dc3ba739131 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -71,7 +71,7 @@
 };
 
 &wkup_pmx0 {
-	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
 			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
-- 
2.17.1

[PATCH V2 8/8] arm64: dts: ti: k3-*: Fix up node_name_chars_strict warnings

[Nishanth Menon]

Building with W=2 throws up a bunch of easy to fixup warnings..
node_name_chars_strict is one of them.. Knock those out.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
---
Changes:
v2: None (rebase) (picked acks/reviews) - comment on hex usage split as
  seperate patch
v1: https://lore.kernel.org/linux-arm-kernel/20200901223059.14801-8-nm@ti.com/

 arch/arm64/boot/dts/ti/k3-am65-main.dtsi       |  6 +++---
 arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi        |  4 ++--
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 16 ++++++++--------
 .../dts/ti/k3-am654-industrial-thermal.dtsi    | 12 ++++++------
 .../boot/dts/ti/k3-j721e-common-proc-board.dts | 18 +++++++++---------
 arch/arm64/boot/dts/ti/k3-j721e-main.dtsi      |  6 +++---
 .../arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi |  2 +-
 arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi    |  2 +-
 8 files changed, 33 insertions(+), 33 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index 1dd488cb15c6..533525229a8d 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -305,7 +305,7 @@
 		no-1-8-v;
 	};
 
-	scm_conf: scm_conf@100000 {
+	scm_conf: scm-conf@100000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0 0x00100000 0 0x1c000>;
 		#address-cells = <1>;
@@ -344,7 +344,7 @@
 					<0x4090 0x3>; /* SERDES1 lane select */
 		};
 
-		dss_oldi_io_ctrl: dss_oldi_io_ctrl@41e0 {
+		dss_oldi_io_ctrl: dss-oldi-io-ctrl@41e0 {
 			compatible = "syscon";
 			reg = <0x0000041e0 0x14>;
 		};
@@ -445,7 +445,7 @@
 		ti,interrupt-ranges = <0 392 32>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index 51ca4b4d4c21..29aaf8dca6f6 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -6,7 +6,7 @@
  */
 
 &cbass_mcu {
-	mcu_conf: scm_conf@40f00000 {
+	mcu_conf: scm-conf@40f00000 {
 		compatible = "syscon", "simple-mfd";
 		reg = <0x0 0x40f00000 0x0 0x20000>;
 		#address-cells = <1>;
@@ -116,7 +116,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 86c9074cb070..d12dd89f3405 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -29,7 +29,7 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		secure_ddr: secure_ddr@9e800000 {
+		secure_ddr: secure-ddr@9e800000 {
 			reg = <0 0x9e800000 0 0x01800000>; /* for OP-TEE */
 			alignment = <0x1000>;
 			no-map;
@@ -70,14 +70,14 @@
 		>;
 	};
 
-	push_button_pins_default: push_button__pins_default {
+	push_button_pins_default: push-button-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0030, PIN_INPUT, 7) /* (R5) WKUP_GPIO0_24 */
 			AM65X_WKUP_IOPAD(0x003c, PIN_INPUT, 7) /* (P2) WKUP_GPIO0_27 */
 		>;
 	};
 
-	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins_default {
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* (V1) MCU_OSPI0_CLK */
 			AM65X_WKUP_IOPAD(0x0008, PIN_INPUT, 0)	 /* (U2) MCU_OSPI0_DQS */
@@ -93,13 +93,13 @@
 		>;
 	};
 
-	wkup_pca554_default: wkup_pca554_default {
+	wkup_pca554_default: wkup-pca554-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
 			AM65X_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* (N5) MCU_RGMII1_RX_CTL */
@@ -116,7 +116,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
 			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02d4, PIN_INPUT_PULLDOWN, 0) /* (C27) MMC1_CLK */
 			AM65X_IOPAD(0x02d8, PIN_INPUT_PULLUP, 0) /* (C28) MMC1_CMD */
@@ -180,7 +180,7 @@
 		>;
 	};
 
-	usb1_pins_default: usb1_pins_default {
+	usb1_pins_default: usb1-pins-default {
 		pinctrl-single,pins = <
 			AM65X_IOPAD(0x02c0, PIN_OUTPUT, 0) /* (AC8) USB1_DRVVBUS */
 		>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
index cdc3d40c3f60..9021c738056b 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am654-industrial-thermal.dtsi
@@ -2,13 +2,13 @@
 
 #include <dt-bindings/thermal/thermal.h>
 
-mpu0_thermal: mpu0_thermal {
+mpu0_thermal: mpu0-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 0>;
 
 	trips {
-		mpu0_crit: mpu0_crit {
+		mpu0_crit: mpu0-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -16,13 +16,13 @@ mpu0_thermal: mpu0_thermal {
 	};
 };
 
-mpu1_thermal: mpu1_thermal {
+mpu1_thermal: mpu1-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 1>;
 
 	trips {
-		mpu1_crit: mpu1_crit {
+		mpu1_crit: mpu1-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
@@ -30,13 +30,13 @@ mpu1_thermal: mpu1_thermal {
 	};
 };
 
-mcu_thermal: mcu_thermal {
+mcu_thermal: mcu-thermal {
 	polling-delay-passive = <250>; /* milliseconds */
 	polling-delay = <500>; /* milliseconds */
 	thermal-sensors = <&wkup_vtm0 2>;
 
 	trips {
-		mcu_crit: mcu_crit {
+		mcu_crit: mcu-crit {
 			temperature = <125000>; /* milliCelsius */
 			hysteresis = <2000>; /* milliCelsius */
 			type = "critical";
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index c355692796a9..648267284582 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -86,13 +86,13 @@
 };
 
 &main_pmx0 {
-	sw10_button_pins_default: sw10_button_pins_default {
+	sw10_button_pins_default: sw10-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x0, PIN_INPUT, 7) /* (AC18) EXTINTn.GPIO0_0 */
 		>;
 	};
 
-	main_mmc1_pins_default: main_mmc1_pins_default {
+	main_mmc1_pins_default: main-mmc1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x254, PIN_INPUT, 0) /* (R29) MMC1_CMD */
 			J721E_IOPAD(0x250, PIN_INPUT, 0) /* (P25) MMC1_CLK */
@@ -106,14 +106,14 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main_usbss0_pins_default {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x290, PIN_OUTPUT, 0) /* (U6) USB0_DRVVBUS */
 			J721E_IOPAD(0x210, PIN_INPUT, 7) /* (W3) MCAN1_RX.GPIO1_3 */
 		>;
 	};
 
-	main_usbss1_pins_default: main_usbss1_pins_default {
+	main_usbss1_pins_default: main-usbss1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x214, PIN_OUTPUT, 4) /* (V4) MCAN1_TX.USB1_DRVVBUS */
 		>;
@@ -153,7 +153,7 @@
 		>;
 	};
 
-	mcasp10_pins_default: mcasp10_pins_default {
+	mcasp10_pins_default: mcasp10-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x158, PIN_OUTPUT_PULLDOWN, 12) /* (U23) RGMII5_TX_CTL.MCASP10_ACLKX */
 			J721E_IOPAD(0x15c, PIN_OUTPUT_PULLDOWN, 12) /* (U26) RGMII5_RX_CTL.MCASP10_AFSX */
@@ -167,7 +167,7 @@
 		>;
 	};
 
-	audi_ext_refclk2_pins_default: audi_ext_refclk2_pins_default {
+	audi_ext_refclk2_pins_default: audi-ext-refclk2-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
 		>;
@@ -175,7 +175,7 @@
 };
 
 &wkup_pmx0 {
-	sw11_button_pins_default: sw11_button_pins_default {
+	sw11_button_pins_default: sw11-button-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xcc, PIN_INPUT, 7) /* (G28) WKUP_GPIO0_7 */
 		>;
@@ -194,7 +194,7 @@
 		>;
 	};
 
-	mcu_cpsw_pins_default: mcu_cpsw_pins_default {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
 			J721E_WKUP_IOPAD(0x005c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
@@ -211,7 +211,7 @@
 		>;
 	};
 
-	mcu_mdio_pins_default: mcu_mdio1_pins_default {
+	mcu_mdio_pins_default: mcu-mdio1-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* MCU_MDIO0_MDC */
 			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 1d2a7c05b6f3..ea57d07777ba 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -86,7 +86,7 @@
 		ti,interrupt-ranges = <8 392 56>;
 	};
 
-	main_navss {
+	main-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -888,7 +888,7 @@
 		no-1-8-v;
 	};
 
-	usbss0: cdns_usb@4104000 {
+	usbss0: cdns-usb@4104000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4104000 0x00 0x100>;
 		dma-coherent;
@@ -918,7 +918,7 @@
 		};
 	};
 
-	usbss1: cdns_usb@4114000 {
+	usbss1: cdns-usb@4114000 {
 		compatible = "ti,j721e-usb";
 		reg = <0x00 0x4114000 0x00 0x100>;
 		dma-coherent;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index 9ad0266598ad..e581cb1d87ee 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -249,7 +249,7 @@
 		};
 	};
 
-	mcu_navss {
+	mcu-navss {
 		compatible = "simple-mfd";
 		#address-cells = <2>;
 		#size-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index d69d90c8b5e3..5dc3ba739131 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -71,7 +71,7 @@
 };
 
 &wkup_pmx0 {
-	wkup_i2c0_pins_default: wkup_i2c0_pins_default {
+	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			J721E_WKUP_IOPAD(0xf8, PIN_INPUT_PULLUP, 0) /* (J25) WKUP_I2C0_SCL */
 			J721E_WKUP_IOPAD(0xfc, PIN_INPUT_PULLUP, 0) /* (H24) WKUP_I2C0_SDA */
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel