From: Greg Ungerer <gerg@kernel.org>
To: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>,
Sascha Hauer <s.hauer@pengutronix.de>,
Boris Brezillon <boris.brezillon@collabora.com>,
linux-mtd@lists.infradead.org,
Boris Brezillon <bbrezillon@kernel.org>
Subject: Re: GPMI iMX6ull timeout on DMA
Date: Fri, 29 Jan 2021 22:43:06 +1000 [thread overview]
Message-ID: <2e9e1f1c-ee57-425d-1791-70c66de52637@kernel.org> (raw)
In-Reply-To: <CAOf5uwmPzCU8WFRQ1tQBdN7OVGZZ9SvdAG0YqVAyxmA1zwtUhg@mail.gmail.com>
Hi Michael,
On 28/1/21 7:45 pm, Michael Nazzareno Trimarchi wrote:
> Hi Greg
>
> On Tue, Aug 13, 2019 at 2:50 AM Greg Ungerer <gerg@kernel.org> wrote:
>>
>> Hi Boris,
>>
>> On 12/8/19 5:31 pm, Boris Brezillon wrote:
>>> On Mon, 12 Aug 2019 12:50:36 +1000
>> [snip]
>>> Hm, CTRL1 is identical. Can you dump all regs at the beginning and at
>>> the end of those funcs?
>>
>> Here is a more complete dump of registers. Trace points are at
>> entry and exit of the respective functions in the different
>> kernel versions. Register dumping code is identical for both.
>>
>>
>> Linux version 4.16.0 (gerg@goober) (gcc version 4.8.3 (GCC)) #10 Tue Aug 13 10:24:28 AEST 2019
>> ...
>
> I ran an overnight reboot process on linux-4.19.y tag: v4.19.169 and
> I'm not able to reproduce up to now.
>
> Do you have an update from your side?
I haven't seen the problem for a while now.
I pretty much only run modern kernels, I am currently using 5.10.
So I am guessing it was resolved somewhere at some point, but I
don't know exactly what change resolved it.
Regards
Greg
>> drivers/mtd/nand/gpmi-nand/gpmi-lib.c(1073): gpmi_begin(): ENTRY
>> HW_GPMI_CTRL0=0x00000000
>> HW_GPMI_CTRL1=0x01c4000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000400
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00010203
>> HW_GPMI_TIMING1=0x00000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x00000000
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000000
>> r->clock[0]=22000000
>> nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
>> nand: Micron MT29F2G08ABAEAWP
>> nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
>> gpmi-nand 1806000.gpmi-nand: enable the asynchronous EDO mode 5
>> drivers/mtd/nand/gpmi-nand/gpmi-lib.c(1073): gpmi_begin(): ENTRY
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x0104000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00010203
>> HW_GPMI_TIMING1=0x05000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x00000000
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000101
>> r->clock[0]=99000000
>> drivers/mtd/nand/gpmi-nand/gpmi-lib.c(1136): gpmi_begin(): EXIT
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x01c6800c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00010101
>> HW_GPMI_TIMING1=0x90000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x00000000
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000101
>> r->clock[0]=99000000
>> Scanning device for bad blocks
>> 5 ofpart partitions found on MTD device gpmi-nand
>> Creating 5 MTD partitions on "gpmi-nand":
>> 0x000000000000-0x000000500000 : "u-boot"
>> 0x000000500000-0x000000600000 : "u-boot-env"
>> 0x000000600000-0x000000800000 : "log"
>> 0x000000800000-0x000010000000 : "flash"
>> 0x000000000000-0x000010000000 : "all"
>> gpmi-nand 1806000.gpmi-nand: driver registered.
>> ...
>>
>> Note that the first ENTRY dump has no matching EXIT dump. From the
>> code I assume it is returning from gpmi_begin() at the
>> "if (!hw.sample_delay_factor)" check.
>>
>>
>> And for the 5.1.14 kernel:
>>
>> Linux version 5.1.14 (gerg@goober) (gcc version 4.8.3 (GCC)) #27 Tue Aug 13 10:20:32 AEST 2019
>> ...
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(512): gpmi_nfc_apply_timings(): ENTRY
>> HW_GPMI_CTRL0=0x00000000
>> HW_GPMI_CTRL1=0x01c4000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000400
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00010203
>> HW_GPMI_TIMING1=0x00000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x00000000
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000000
>> r->clock[0]=22000000
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(536): gpmi_nfc_apply_timings(): EXIT
>> HW_GPMI_CTRL0=0x00000000
>> HW_GPMI_CTRL1=0x0104000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000400
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00020101
>> HW_GPMI_TIMING1=0x60000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x00000000
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000000
>> r->clock[0]=22000000
>> random: fast init done
>> nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
>> nand: Micron MT29F2G08ABAEAWP
>> nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(512): gpmi_nfc_apply_timings(): ENTRY
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x0104000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00020101
>> HW_GPMI_TIMING1=0x60000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x0000003f
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000101
>> r->clock[0]=22000000
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(536): gpmi_nfc_apply_timings(): EXIT
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x0104000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00020101
>> HW_GPMI_TIMING1=0xb0000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x0000003f
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000101
>> r->clock[0]=22000000
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(512): gpmi_nfc_apply_timings(): ENTRY
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x0104000c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00020101
>> HW_GPMI_TIMING1=0xb0000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x000000e0
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000000
>> r->clock[0]=22000000
>> drivers/mtd/nand/raw/gpmi-nand/gpmi-lib.c(536): gpmi_nfc_apply_timings(): EXIT
>> HW_GPMI_CTRL0=0x01800001
>> HW_GPMI_CTRL1=0x01c6800c
>> HW_GPMI_COMPARE=0x00000000
>> HW_GPMI_ECCCTRL=0x00000000
>> HW_GPMI_ECCCOUNT=0x00000000
>> HW_GPMI_PAYLOAD=0x00000000
>> HW_GPMI_AUXILIARY=0x00000000
>> HW_GPMI_TIMING0=0x00010101
>> HW_GPMI_TIMING1=0xe0000000
>> HW_GPMI_TIMING2=0x23023336
>> HW_GPMI_DATA=0x000000e0
>> HW_GPMI_STAT=0xff000005
>> HW_GPMI_DEBUG=0x00000000
>> r->clock[0]=99000000
>> Scanning device for bad blocks
>> 5 fixed-partitions partitions found on MTD device gpmi-nand
>> Creating 5 MTD partitions on "gpmi-nand":
>> 0x000000000000-0x000000500000 : "u-boot"
>> 0x000000500000-0x000000600000 : "u-boot-env"
>> 0x000000600000-0x000000800000 : "log"
>> 0x000000800000-0x000010000000 : "flash"
>> 0x000000000000-0x000010000000 : "all"
>> gpmi-nand 1806000.gpmi-nand: driver registered.
>> ...
>>
>>
>> Regards
>> Greg
>>
>>
>
>
______________________________________________________
Linux MTD discussion mailing list
http://lists.infradead.org/mailman/listinfo/linux-mtd/
next prev parent reply other threads:[~2021-01-29 12:44 UTC|newest]
Thread overview: 85+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-07-29 6:41 GPMI iMX6ull timeout on DMA Greg Ungerer
2019-07-29 8:36 ` Miquel Raynal
2019-07-29 8:42 ` Michael Nazzareno Trimarchi
2019-07-29 12:18 ` Greg Ungerer
2019-07-29 12:20 ` Michael Nazzareno Trimarchi
2019-07-29 12:33 ` Greg Ungerer
2019-07-29 12:47 ` Miquel Raynal
2019-07-29 12:49 ` Michael Nazzareno Trimarchi
2019-07-29 12:55 ` Miquel Raynal
2019-07-29 13:00 ` Michael Nazzareno Trimarchi
2019-07-29 13:22 ` Miquel Raynal
2019-07-29 20:00 ` Michael Nazzareno Trimarchi
2019-07-29 21:02 ` Miquel Raynal
2019-07-30 0:28 ` Greg Ungerer
2019-07-30 0:41 ` Greg Ungerer
2019-07-30 6:06 ` Greg Ungerer
2019-07-30 8:38 ` Miquel Raynal
2019-07-30 8:58 ` Boris Brezillon
2019-07-31 2:05 ` Greg Ungerer
2019-07-31 6:28 ` Boris Brezillon
2019-08-02 7:19 ` Greg Ungerer
2019-08-02 12:34 ` Greg Ungerer
2019-08-02 12:51 ` Boris Brezillon
2019-08-05 5:51 ` Greg Ungerer
2019-08-07 16:05 ` Miquel Raynal
2019-08-08 0:43 ` Greg Ungerer
2019-08-08 16:36 ` Boris Brezillon
2019-08-09 5:20 ` Greg Ungerer
2019-08-09 6:23 ` Boris Brezillon
2019-08-09 6:55 ` Greg Ungerer
2019-08-09 7:32 ` Boris Brezillon
2019-08-09 13:57 ` Greg Ungerer
2019-08-09 13:59 ` Boris Brezillon
2019-08-12 2:50 ` Greg Ungerer
2019-08-12 4:04 ` Greg Ungerer
2019-08-12 7:31 ` Boris Brezillon
2019-08-13 0:50 ` Greg Ungerer
2021-01-28 9:45 ` Michael Nazzareno Trimarchi
2021-01-28 10:26 ` Miquel Raynal
2021-01-28 10:35 ` Michael Nazzareno Trimarchi
2021-01-28 11:55 ` Michael Nazzareno Trimarchi
2021-01-29 12:43 ` Greg Ungerer [this message]
2021-01-30 9:41 ` Michael Nazzareno Trimarchi
2021-02-01 14:13 ` Miquel Raynal
2021-02-01 14:32 ` Michael Nazzareno Trimarchi
2021-02-01 15:08 ` Michael Nazzareno Trimarchi
2021-02-01 15:14 ` Miquel Raynal
2021-02-01 15:17 ` Michael Nazzareno Trimarchi
2021-10-15 20:05 ` Michael Trimarchi
2021-10-15 20:12 ` Michael Nazzareno Trimarchi
2021-10-18 7:19 ` Miquel Raynal
2021-10-18 7:33 ` Michael Nazzareno Trimarchi
2021-10-18 7:43 ` Miquel Raynal
2021-10-04 5:54 ` Christian Eggers
2021-10-04 6:27 ` Michael Nazzareno Trimarchi
2021-10-04 15:33 ` Miquel Raynal
2021-10-04 16:06 ` Han Xu
2021-10-05 6:02 ` Christian Eggers
2021-10-08 9:55 ` Christian Eggers
2021-10-08 12:08 ` Stefan Riedmüller
2021-10-08 12:27 ` Miquel Raynal
2021-10-08 13:11 ` Christian Eggers
2021-10-08 13:29 ` Miquel Raynal
2021-10-08 13:36 ` Miquel Raynal
2021-10-08 13:49 ` Christian Eggers
2021-10-08 16:07 ` Miquel Raynal
2021-10-09 5:53 ` Michael Nazzareno Trimarchi
2021-10-11 6:46 ` Miquel Raynal
2021-10-12 9:02 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Stefan Riedmueller
2021-10-12 9:02 ` [RFC PATCH 2/2] gpmi-nand: Add ERR007117 protection for nfc_apply_timings Stefan Riedmueller
2021-10-13 5:01 ` Han Xu
2021-10-22 8:45 ` Stefan Riedmüller
2021-10-22 14:35 ` han.xu
2021-10-25 9:39 ` Stefan Riedmüller
2021-10-28 9:28 ` Stefan Riedmüller
2021-11-01 4:01 ` han.xu
2021-10-13 6:10 ` Christian Eggers
2021-10-13 6:00 ` [RFC PATCH 1/2] mtd: rawnand: gpmi: Remove explicit default gpmi clock setting for i.MX6 Christian Eggers
2021-10-09 6:26 ` GPMI iMX6ull timeout on DMA Christian Eggers
2021-10-13 6:15 ` Christian Eggers
2021-10-08 13:13 ` Christian Eggers
2021-10-08 13:30 ` Miquel Raynal
2021-10-09 6:33 ` Christian Eggers
-- strict thread matches above, loose matches on Subject: below --
2018-10-02 13:22 GPMI IMX6ull timeout on dma Michael Nazzareno Trimarchi
2018-10-04 14:36 ` Michael Nazzareno Trimarchi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2e9e1f1c-ee57-425d-1791-70c66de52637@kernel.org \
--to=gerg@kernel.org \
--cc=bbrezillon@kernel.org \
--cc=boris.brezillon@collabora.com \
--cc=linux-mtd@lists.infradead.org \
--cc=michael@amarulasolutions.com \
--cc=miquel.raynal@bootlin.com \
--cc=s.hauer@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).