netdev.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Russell King - ARM Linux admin <linux@armlinux.org.uk>
To: "Pali Rohár" <pali@kernel.org>
Cc: "Andrew Lunn" <andrew@lunn.ch>,
	"Thomas Schreiber" <tschreibe@gmail.com>,
	"Heiner Kallweit" <hkallweit1@gmail.com>,
	"David S. Miller" <davem@davemloft.net>,
	"Jakub Kicinski" <kuba@kernel.org>,
	"Marek Behún" <kabel@kernel.org>,
	netdev@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 1/4] net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips
Date: Wed, 6 Jan 2021 15:21:38 +0000	[thread overview]
Message-ID: <20210106152138.GK1551@shell.armlinux.org.uk> (raw)
In-Reply-To: <20210106145532.xynhoufpfyzmurd5@pali>

On Wed, Jan 06, 2021 at 03:55:32PM +0100, Pali Rohár wrote:
> On my tested CarlitoxxPro module is:
> 
>         Option values                             : 0x00 0x1c
>         Option                                    : RX_LOS implemented, inverted
>         Option                                    : TX_FAULT implemented
>         Option                                    : TX_DISABLE implemented
> 
> When cable is disconnected then in EEPROM at position 0x16e is value
> 0x82. If I call 'ip link set eth1 up' then value changes to 0x02, module
> itself has a link and I can connect to its internal telnet/webserver to
> configure it.

Bit 7 reflects the TX_DISABLE pin state. Bit 1 reflects the RX_LOS pin
state. It isn't specified whether the inverted/non-inverted state is
reflected in bit 1 or not - the definition just says that bit 1 is
"Digital state of the RX_LOS Output Pin."

> I also tested UBNT module and result is:
> 
>         Option values                             : 0x00 0x06
>         Option                                    : RX_LOS implemented
>         Option                                    : RX_LOS implemented, inverted
> 
> Which means that those bits are not implemented.
> 
> Anyway I check position 0x16e and value on its value is randomly either
> 0x79 or 0xff independently of the state of the GPON module.
> 
> So it is really not implemented on UBNT.

There are enhanced options at offset 93 which tell you which of the
offset 110 signals are implemented.

We already have support for these, but only when the corresponding
GPIOs on the host side are not implemented.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 40Mbps down 10Mbps up. Decent connectivity at last!

  reply	other threads:[~2021-01-06 15:22 UTC|newest]

Thread overview: 78+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-12-30 15:47 [PATCH 0/4] net: sfp: add support for GPON RTL8672/RTL9601C and Ubiquiti U-Fiber Pali Rohár
2020-12-30 15:47 ` [PATCH 1/4] net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips Pali Rohár
2020-12-30 16:10   ` Russell King - ARM Linux admin
2020-12-30 16:56     ` Pali Rohár
2020-12-30 17:05       ` Russell King - ARM Linux admin
2020-12-30 17:13         ` Andrew Lunn
2020-12-30 17:43           ` Pali Rohár
2020-12-30 19:09             ` Russell King - ARM Linux admin
2020-12-30 19:49               ` Andrew Lunn
2020-12-31 12:14               ` Pali Rohár
2020-12-31 15:09                 ` Andrew Lunn
2020-12-31 15:40                   ` Pali Rohár
2020-12-31 15:30                 ` Andrew Lunn
2020-12-31 17:00                   ` Pali Rohár
2020-12-31 17:13                     ` Andrew Lunn
2021-01-02  1:49                       ` Pali Rohár
2021-01-03  2:25                         ` Thomas Schreiber
2021-01-03  2:41                           ` Pali Rohár
2021-01-06 14:55                             ` Pali Rohár
2021-01-06 15:21                               ` Russell King - ARM Linux admin [this message]
2021-01-06 15:23                                 ` Russell King - ARM Linux admin
2021-01-06 15:27                                   ` Russell King - ARM Linux admin
2021-01-06 15:35                                     ` Pali Rohár
2020-12-30 19:30             ` Andrew Lunn
2020-12-30 19:39               ` Russell King - ARM Linux admin
2020-12-30 17:31         ` Pali Rohár
2020-12-30 19:18           ` Russell King - ARM Linux admin
2020-12-30 15:47 ` [PATCH 2/4] net: sfp: allow to use also SFP modules which are detected as SFF Pali Rohár
2020-12-30 16:11   ` Russell King - ARM Linux admin
2020-12-30 17:06     ` Pali Rohár
2020-12-30 17:27       ` Marek Behún
2020-12-30 19:12         ` Russell King - ARM Linux admin
2020-12-31 13:52           ` Pali Rohár
2020-12-30 15:47 ` [PATCH 3/4] net: sfp: assume that LOS is not implemented if both LOS normal and inverted is set Pali Rohár
2020-12-30 16:13   ` Russell King - ARM Linux admin
2020-12-30 16:57     ` Pali Rohár
2020-12-30 17:06       ` Russell King - ARM Linux admin
2020-12-30 17:17         ` Andrew Lunn
2020-12-30 17:32           ` Pali Rohár
2020-12-30 15:47 ` [PATCH 4/4] net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant Pali Rohár
2021-01-06 15:37 ` [PATCH v2 0/3] net: sfp: add support for GPON RTL8672/RTL9601C and Ubiquiti U-Fiber Pali Rohár
2021-01-06 15:37   ` [PATCH v2 1/3] net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips Pali Rohár
2021-01-07  2:02     ` Andrew Lunn
2021-01-07  9:08       ` Pali Rohár
2021-01-07 17:19     ` Andrew Lunn
2021-01-07 17:40       ` Russell King - ARM Linux admin
2021-01-07 19:18         ` Pali Rohár
2021-01-07 19:17       ` Pali Rohár
2021-01-07 19:45       ` Russell King - ARM Linux admin
2021-01-07 20:21         ` Marek Behún
2021-01-08  0:49           ` Pali Rohár
2021-01-06 15:37   ` [PATCH v2 2/3] net: sfp: assume that LOS is not implemented if both LOS normal and inverted is set Pali Rohár
2021-01-07 16:54     ` Andrew Lunn
2021-01-09 15:46       ` Russell King - ARM Linux admin
2021-01-09 15:54         ` Andrew Lunn
2021-01-09 16:27           ` Russell King - ARM Linux admin
2021-01-09 19:14         ` Pali Rohár
2021-01-09 23:19           ` Russell King - ARM Linux admin
2021-01-09 23:50             ` Pali Rohár
2021-01-06 15:37   ` [PATCH v2 3/3] net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant Pali Rohár
2021-01-07 16:51     ` Andrew Lunn
2021-01-11 11:39 ` [PATCH v3 0/2] net: sfp: add support for GPON RTL8672/RTL9601C and Ubiquiti U-Fiber Pali Rohár
2021-01-11 11:39   ` [PATCH v3 1/2] net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips Pali Rohár
2021-01-11 15:28     ` Marek Behún
2021-01-11 11:39   ` [PATCH v3 2/2] net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant Pali Rohár
2021-01-11 15:32     ` Marek Behún
2021-01-12 13:33   ` [PATCH v3 0/2] net: sfp: add support for GPON RTL8672/RTL9601C and Ubiquiti U-Fiber Pali Rohár
2021-01-18  9:34   ` Pali Rohár
2021-01-25 14:09     ` Pali Rohár
2021-01-25 14:16       ` Russell King - ARM Linux admin
2021-01-25 14:23         ` Pali Rohár
2021-01-25 14:42           ` Russell King - ARM Linux admin
2021-01-25 14:47             ` Pali Rohár
2021-01-25 15:41               ` Andrew Lunn
2021-01-25 15:02 ` [PATCH v4 " Pali Rohár
2021-01-25 15:02   ` [PATCH v4 1/2] net: sfp: add workaround for Realtek RTL8672 and RTL9601C chips Pali Rohár
2021-01-25 15:02   ` [PATCH v4 2/2] net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant Pali Rohár
2021-01-28 21:50   ` [PATCH v4 0/2] net: sfp: add support for GPON RTL8672/RTL9601C and Ubiquiti U-Fiber patchwork-bot+netdevbpf

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20210106152138.GK1551@shell.armlinux.org.uk \
    --to=linux@armlinux.org.uk \
    --cc=andrew@lunn.ch \
    --cc=davem@davemloft.net \
    --cc=hkallweit1@gmail.com \
    --cc=kabel@kernel.org \
    --cc=kuba@kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=netdev@vger.kernel.org \
    --cc=pali@kernel.org \
    --cc=tschreibe@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).