[U-Boot] [PULL] : Please pull u-boot-imx

[Albert ARIBAUD <albert.u.boot@aribaud.net>]

Hi Stefano,

On Wed, 19 Feb 2014 11:04:53 +0100, Stefano Babic <sbabic@denx.de>
wrote:

> Hi Albert,
> 
> please pull from u-boot-imx, thanks !
> 
> 
> The following changes since commit e97f9d817e600cd6f43d1d0da76f5787e33a5c56:
> 
>   Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' (2014-01-29
> 14:07:50 +0100)
> 
> are available in the git repository at:
> 
> 
>   git://www.denx.de/git/u-boot-imx.git master
> 
> for you to fetch changes up to da781c60e5d55904d77931fcb63f25e65e2228be:
> 
>   imx6 SION bit has to be on for the pins that are used as ENET_REF_CLK
> (2014-02-19 10:57:25 +0100)
> 
> ----------------------------------------------------------------
> Andy Ng (1):
>       imx6 SION bit has to be on for the pins that are used as ENET_REF_CLK
> 
> Anson Huang (2):
>       imx6: ensure AHB clock is 132MHz in low freq boot mode
>       imx6: make sure MMDC_CHx_MASK is clear to avoid warm reset failure
> 
> Eric Nelson (1):
>       i.MX6: nitrogen6x: pedantic: BOOT_FROM==spi, not sd
> 
> Fabio Estevam (8):
>       nitrogen6x: README: Only calling 'make' is enough
>       nitrogen6x: README: Do not refer to MAINTAINERS file
>       mx6sl: Adjust fdt_addr to avoid address overlapping
>       hummingboard: Return from cpu_eth_init() directly
>       imx: Introduce a header for the imx cpu versions
>       mx6: Distinguish mx6dual from mx6quad
>       mx6qsabreauto: Update imximage.cfg
>       mx6: Enable L2 cache support
> 
> Marek Vasut (7):
>       ARM: armv7: Make indirect vector addresses globl
>       ARM: mx6: Add PCI express clock configuration
>       ARM: mx6: Add PCI express driver
>       ARM: mx6: Enable PCIe on Sabrelite
>       ARM: m53evk: Rename mxc-nand to mxc_nand
>       ARM: m53evk: Enable CONFIG_REGEX
>       pci: mx6: Implement reset callback
> 
> Markus Niebel (2):
>       ARM: imx6: fix wrong fec clk
>       NET: fec_mxc: fix MDIO clock prescaler calculation
> 
> Otavio Salvador (11):
>       cgtqmx6eval: Set default environment to use zImage
>       hummingboard: Set default environment to use zImage
>       mx23evk: Set default environment to use zImage
>       mx28evk: Set default environment to use zImage
>       mx51evk: Set default environment to use zImage
>       mx53loco: Set default environment to use zImage
>       mx6qarm2: Set default environment to use zImage
>       mx6sabre_common: Set default environment to use zImage
>       mx6slevk: Set default environment to use zImage
>       udoo: Set default environment to use zImage
>       vf610twr: Set default environment to use zImage
> 
> Stefano Babic (2):
>       Merge branch 'master' of git://git.denx.de/u-boot-arm
>       Merge branch 'master' of git://git.denx.de/u-boot-arm
> 
>  arch/arm/cpu/armv7/mx6/clock.c              |   77 +++-
>  arch/arm/cpu/armv7/mx6/soc.c                |  103 ++++-
>  arch/arm/cpu/armv7/start.S                  |    7 +
>  arch/arm/imx-common/cpu.c                   |    2 +
>  arch/arm/include/asm/arch-imx/cpu.h         |   13 +
>  arch/arm/include/asm/arch-mx5/sys_proto.h   |    7 +-
>  arch/arm/include/asm/arch-mx6/clock.h       |    1 +
>  arch/arm/include/asm/arch-mx6/imx-regs.h    |    1 +
>  arch/arm/include/asm/arch-mx6/iomux.h       |   27 ++
>  arch/arm/include/asm/arch-mx6/mx6dl_pins.h  |    6 +-
>  arch/arm/include/asm/arch-mx6/mx6q_pins.h   |    6 +-
>  arch/arm/include/asm/arch-mx6/sys_proto.h   |    8 +-
>  arch/arm/include/asm/pl310.h                |   21 +
>  board/boundary/nitrogen6x/README            |    4 +-
>  board/boundary/nitrogen6x/nitrogen6dl.cfg   |    2 +-
>  board/boundary/nitrogen6x/nitrogen6dl2g.cfg |    2 +-
>  board/boundary/nitrogen6x/nitrogen6q.cfg    |    2 +-
>  board/boundary/nitrogen6x/nitrogen6q2g.cfg  |    2 +-
>  board/boundary/nitrogen6x/nitrogen6s.cfg    |    2 +-
>  board/boundary/nitrogen6x/nitrogen6s1g.cfg  |    2 +-
>  board/freescale/mx6qsabreauto/imximage.cfg  |  136 +++---
>  board/solidrun/hummingboard/hummingboard.c  |    6 +-
>  drivers/net/fec_mxc.c                       |    8 +-
>  drivers/pci/Makefile                        |    1 +
>  drivers/pci/pcie_imx.c                      |  606
> +++++++++++++++++++++++++++
>  include/configs/cgtqmx6eval.h               |   14 +-
>  include/configs/hummingboard.h              |   20 +-
>  include/configs/m53evk.h                    |    6 +-
>  include/configs/mx23evk.h                   |   12 +-
>  include/configs/mx28evk.h                   |   26 +-
>  include/configs/mx51evk.h                   |   20 +-
>  include/configs/mx53loco.h                  |   20 +-
>  include/configs/mx6_common.h                |    5 +
>  include/configs/mx6qarm2.h                  |   10 +-
>  include/configs/mx6sabre_common.h           |   20 +-
>  include/configs/mx6slevk.h                  |   22 +-
>  include/configs/nitrogen6x.h                |   11 +
>  include/configs/udoo.h                      |   20 +-
>  include/configs/vf610twr.h                  |   20 +-
>  39 files changed, 1049 insertions(+), 229 deletions(-)
>  create mode 100644 arch/arm/include/asm/arch-imx/cpu.h
>  create mode 100644 drivers/pci/pcie_imx.c
> 
> 
> 

Applied to u-boot-arm/master, thanks!

Amicalement,
-- 
Albert.